Home › Drivetrain › P710 (HYBRID TRANSMISSION / TRANSAXLE) › INPUT SHAFT OIL SEAL › from 2021.02
RM33C0E _52 Drivetrain _065428 P710 HYBRID TRANSMISSION / TRANSAXLE _0319555 INPUT SHAFT OIL SEAL A

P710 HYBRID TRANSMISSION / TRANSAXLE  INPUT SHAFT OIL SEAL  REPLACEMENT  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during hybrid vehicle transaxle assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: The vehicle height changes because of suspension or tire replacement.

Auxiliary battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane Tracing Assist System (Click here)
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic View Monitor System (Click here)
Replacement of ECM Vehicle Identification Number (VIN) or frame number registration MIL illuminates (Click here)(w/ Canister Pump Module)
(Click here)(w/o Canister Pump Module)
·

Replacement of engine assembly

·

Replacement of air fuel ratio sensor (sensor 2)

·

Replacement of engine coolant temperature sensor

(w/ Canister Pump Module)

·

Gas leak from exhaust system is repaired


Inspection after repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)(w/ Canister Pump Module)
(Click here)(w/o Canister Pump Module)
Replacement of inverter with converter assembly Resolver learning
·

DTCs are stored

·

Slight vibration at a vehicle speed of 5 km/h (3 mph) or less

·

Shock or vibration during acceleration


(Click here)for Nickel Metal Hydride Battery
(Click here)for Lithium-ion Battery
Front wheel alignment adjustment
1.

Clear zero point calibration data.

2.

Perform yaw rate and acceleration sensor zero point calibration.


·

DTCs are stored

·

ABS warning light illuminates

·

Brake warning light / yellow (minor malfunction) illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)
Suspension, tires, etc.*1 Rear television camera assembly optical axis (Back camera position setting) Parking assist monitor system (Click here)for Initialization
(Click here)for Calibration
Replacement of headlight ECU sub-assembly LH
·

Synchronize the vehicle information

·

Perform headlight ECU sub-assembly LH initialization


Lighting System (EXT) (w/ Automatic Headlight Beam Level Control System) (Click here)
Suspension, tires, etc.*1 Perform headlight ECU sub-assembly LH initialization
Suspension, tires, etc.*1
·

Measure ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking Support Brake System (Click here)
Suspension, tires, etc.*1
·

Television camera controller initialization

·

Adjust steering angle

·

Rear television camera assembly optical axis (Back camera position setting)


Panoramic View Monitor System (Click here)for Initialization
(Click here)for Calibration

CAUTION:
·
A340386

Orange wire harnesses and connectors indicate high-voltage circuits. To prevent electric shock, always follow the procedure described in the repair manual.

for Nickel Metal Hydride Battery: Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for NICKEL METAL HYDRIDE BATTERY)>PRECAUTION

for Lithium-ion Battery: Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for LITHIUM-ION BATTERY)>PRECAUTION

·
A340358

To prevent electric shock, wear insulated gloves when working on wire harnesses and components of the high voltage system.

·
A344784

To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.

·
A344783

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.

·
A346363C01
2.219,0.813 2.646,0.813 false 2.698,0.729 3.01,0.927 0.313,0.198 10 false *a
*a An Object Exceeding Weight Limit of Engine Lifter


The engine assembly with transaxle is very heavy. Be sure to follow the procedure described in the repair manual, or the engine lifter may suddenly drop or the engine assembly with transaxle may fall off the engine lifter.

·
C313282C01
2.573,0.583 2.906,0.583 false 2.948,0.479 3.26,0.677 0.313,0.198 10 false *a
*a Object Exceeding Weight Limit of Transmission Jack


The hybrid vehicle transaxle assembly is very heavy. Be sure to follow the procedure described in the repair manual, or the transmission jack may suddenly drop or a part may fall.



NOTICE:
·

After the power switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the power switch off, make sure to wait at least 85 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal.

·

If the ECM has been struck or dropped, replace it.

·

Perform Vehicle Identification Number (VIN) registration when replacing the ECM.

w/ Canister Pump Module: Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>SFI SYSTEM (w/ Canister Pump Module)>REGISTRATION

w/o Canister Pump Module: Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>SFI SYSTEM (w/o Canister Pump Module)>REGISTRATION



PROCEDURE

Hide 30900 1.REMOVE HYBRID VEHICLE TRANSAXLE ASSEMBLY

Hide 35710A 2.REMOVE INPUT SHAFT TYPE T OIL SEAL

a.
C377405C02
1.188,0.344 1.479,0.344 1.479,0.344 1.844,1 true 1.021,0.25 1.302,0.458 0.281,0.208 10 false *a
*a Protective Tape


Using a screwdriver with its tip wrapped with protective tape, remove the input shaft type T oil seal from the hybrid vehicle transaxle assembly.

NOTICE:

Be careful not to damage the input shaft assembly or hybrid vehicle transaxle assembly.



Hide 35710A 3.INSTALL INPUT SHAFT TYPE T OIL SEAL

a.

Coat the lip of a new input shaft type T oil seal with a small amount of MP grease.


b.
C377942C01
1.99,1.969 2.365,3.021 2.365,3.021 2.521,3.021 true 1.385,0.115 1.667,0.333 0.281,0.219 10 false *a 2.563,2.927 3.021,3.125 0.458,0.198 10 false SST
*a Depth


Using SST and a hammer, install the input shaft type T oil seal to the hybrid vehicle transaxle assembly.

SST
09608-04031  

Standard Depth:

1.9 to 2.7 mm (0.0748 to 0.106 in.)


NOTICE:
·

Do not allow foreign matter to attach to the lip of the input shaft type T oil seal.

·

Do not install the input shaft type T oil seal at an angle.




Hide 30900 4.INSTALL HYBRID VEHICLE TRANSAXLE ASSEMBLY