Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › from 2021.02
RM33C0E _58 Vehicle Interior _065458 METER / GAUGE / DISPLAY _0330016 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Steering Pad Switch Circuit  


DESCRIPTION

The combination meter assembly and steering pad switch assembly are connected via direct line. The multi-information display in the combination meter assembly are operated using the switches of the steering pad switch assembly.

WIRING DIAGRAM

E380804E07
1.406,0.938 1.563,1.135 0.156,0.198 10 false 5 1.406,0.417 1.563,0.615 0.156,0.198 10 false 4 1.375,1.156 1.688,1.354 0.313,0.198 10 false z1 1.365,2.323 1.677,2.521 0.313,0.198 10 false z1 1.365,0.625 1.677,0.823 0.313,0.198 10 false z1 1.365,2.104 1.677,2.302 0.313,0.198 10 false 10 3.292,2.323 3.75,2.521 0.458,0.198 10 false K22 3.292,0.625 3.75,0.823 0.458,0.198 10 false K22 3.292,1.156 3.75,1.354 0.458,0.198 10 false K22 3.344,0.938 3.656,1.135 0.313,0.198 10 false 10 3.344,0.417 3.656,0.615 0.313,0.198 10 false 11 3.375,2.104 3.531,2.302 0.156,0.198 10 false 4 4.531,1.052 4.844,1.25 0.313,0.198 10 false 28 4.542,0.521 4.854,0.719 0.313,0.198 10 false 29 4.792,2.219 5.104,2.417 0.313,0.198 10 false 24 6.281,0.323 6.74,0.521 0.458,0.198 10 false 5 V 4.385,2.219 4.698,2.417 0.313,0.198 10 false *1 4.344,2.625 4.656,2.823 0.313,0.198 10 false *2 6.333,2.208 6.49,2.406 0.156,0.198 10 false 1 4.813,1.052 5.427,1.25 0.615,0.198 10 false MSM+ 4.813,0.521 5.427,0.719 0.615,0.198 10 false MSTI 2.813,1.052 3.427,1.25 0.615,0.198 10 false +DP2 2.875,0.521 3.333,0.719 0.458,0.198 10 false +DP 2.865,2.219 3.323,2.417 0.458,0.198 10 false EAU 5.063,2.323 5.521,2.521 0.458,0.198 10 false SWG 5.854,2.333 6.469,2.531 0.615,0.198 10 false GND1 4.833,1.615 5.292,1.813 0.458,0.198 10 false K21 5.135,1.615 7.156,2.01 2.021,0.396 10 false Combination Meter Assembly 4.813,2.885 6.51,3.427 1.698,0.542 10 false Radio and Display Receiver Assembly*1 4.813,2.729 5.125,2.927 0.313,0.198 10 false K3 1.615,3.219 5.438,3.417 3.823,0.198 10 false Spiral Cable Sub-assembly 3.302,5.927 6.615,6.229 3.313,0.302 10 false Steering Pad Switch Assembly 0.542,6.365 6.813,6.563 6.271,0.198 10 false *1: w/ Radio and Display Receiver Assembly 3.708,6.365 6.771,6.635 3.063,0.271 10 false *2: w/o Radio and Display Receiver Assembly 3.052,4.365 3.667,4.563 0.615,0.198 10 false LEFT 4.083,4.365 4.396,4.563 0.313,0.198 10 false UP 5.094,4.365 5.708,4.563 0.615,0.198 10 false DOWN 6.104,4.365 6.875,4.563 0.771,0.198 10 false RIGHT 3.031,5.125 3.344,5.323 0.313,0.198 10 false OK 4.073,5.125 4.688,5.323 0.615,0.198 10 false BACK

CAUTION / NOTICE / HINT

NOTICE:

When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.


PROCEDURE

1.INSPECT STEERING PAD SWITCH ASSEMBLY
a.

Remove the steering pad switch assembly.

Click hereSteering>STEERING COLUMN>STEERING PAD SWITCH>REMOVAL


b.

Inspect the steering pad switch assembly.

Click hereSteering>STEERING COLUMN>STEERING PAD SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

2.INSPECT SPIRAL CABLE SUB-ASSEMBLY

NG

REPLACE STEERING PAD SWITCH ASSEMBLY

2.INSPECT SPIRAL CABLE SUB-ASSEMBLY
a.

Remove the spiral cable sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>REMOVAL


b.

Inspect the spiral cable sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSPECTION


Result:
Proceed to
OK
NG



OK

3.CONFIRM MODEL

NG

REPLACE SPIRAL CABLE SUB-ASSEMBLY

3.CONFIRM MODEL
a.

Choose the model to be inspected.


Result:
Result Proceed to
w/ Radio and Display Receiver Assembly A
w/o Radio and Display Receiver Assembly B



A

4.CHECK COMBINATION METER ASSEMBLY (OUTPUT VOLTAGE)

B

7.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - COMBINATION METER ASSEMBLY AND BODY GROUND)
4.CHECK COMBINATION METER ASSEMBLY (OUTPUT VOLTAGE)
a.

Connect the K21 combination meter assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
K22-10 (+DP2) - Body ground Power switch on (IG) 4.8 to 5.2 V
K22-11 (+DP) - Body ground Power switch on (IG) 4.8 to 5.2 V



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - RADIO AND DISPLAY RECEIVER ASSEMBLY AND BODY GROUND)

NG

6.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - COMBINATION METER ASSEMBLY)
5.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - RADIO AND DISPLAY RECEIVER ASSEMBLY AND BODY GROUND)
a.

Disconnect the K3 radio and display receiver assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K22-4 (EAU) - K3-24 (SWG) Always Below 1 Ω
K3-1 (GND1) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - COMBINATION METER ASSEMBLY)
a.

Disconnect the K21 combination meter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K22-10 (+DP2) - K21-28 (MSM+) Always Below 1 Ω
K22-11 (+DP) - K21-29 (MSTI) Always Below 1 Ω
K22-10 (+DP2) or K21-28 (MSM+) - Body ground Always 10 kΩ or higher
K22-11 (+DP) or K21-29 (MSTI) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - COMBINATION METER ASSEMBLY AND BODY GROUND)
a.

Disconnect the K21 combination meter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K22-10 (+DP2) - K21-28 (MSM+) Always Below 1 Ω
K22-11 (+DP) - K21-29 (MSTI) Always Below 1 Ω
K22-4 (EAU) - Body ground Always Below 1 Ω
K22-10 (+DP2) or K21-28 (MSM+) - Body ground Always 10 kΩ or higher
K22-11 (+DP) or K21-29 (MSTI) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR