Home › Engine / Hybrid System › 1BZ-FPE (ENGINE CONTROL) › ELECTRONIC CONTROLLED CARBURETOR SYSTEM › 2017.01–2021.01
RM2850E _51 Engine / Hybrid System _073136 1BZ-FPE ENGINE CONTROL _0355837 ELECTRONIC CONTROLLED CARBURETOR SYSTEM C

1BZ-FPE ENGINE CONTROL  ELECTRONIC CONTROLLED CARBURETOR SYSTEM  P0141  Oxygen Sensor Heater Circuit (Bank 1 Sensor 2)  


DESCRIPTION

Refer to DTC P0136 (Click here Engine / Hybrid System>1BZ-FPE (ENGINE CONTROL)>ELECTRONIC CONTROLLED CARBURETOR SYSTEM>P0136).

HINT:

The ECM provides a pulse width modulated control circuit to adjust current through the heater. The heated oxygen sensor heater circuit uses a relay on the +B side of the circuit.


A429945E01
0.052,0.042 2.656,0.302 2.604,0.26 12 false Reference (System Diagram): 5.052,1.219 5.604,1.427 0.552,0.208 10 false HT1B 3.969,1.24 4.438,1.438 0.469,0.198 10 false HT1B 3.292,1.25 3.531,1.406 0.24,0.156 10 false +B 5.052,1.74 5.563,1.938 0.51,0.198 10 false OX1B 3.969,1.76 4.375,1.99 0.406,0.229 10 false OX1B 5.052,2.49 5.458,2.729 0.406,0.24 10 false E2 3.302,1.76 3.625,1.948 0.323,0.188 10 false E2 1.958,2.875 4.458,3.167 2.5,0.292 10 false from ENG STOP/P LOCK NO.2 Relay 3.542,1.51 4.01,1.688 0.469,0.177 10 false Heater 3.531,2.042 4,2.24 0.469,0.198 10 false Sensor 2,2.354 2.333,2.573 0.333,0.219 10 false EFI 1.094,1.51 1.781,1.708 0.688,0.198 10 false EFI-MAIN 3.073,2.365 4.635,2.604 1.563,0.24 10 false Heated Oxygen Sensor 0.24,1.24 0.76,1.615 0.521,0.375 10 false from P/I Fuse 5.781,2.938 6.229,3.094 0.448,0.156 10 false ECM

DTC No. DTC Detecting Condition Trouble Area
P0141/27 heater resistance is outside the specified range when heater operates
(2 trip detection logic)
·

Open or short in heater circuit of heated oxygen sensor

·

Heated oxygen sensor heater

·

EFI MAIN relay

·

ECM



MONITOR DESCRIPTION

The sensing portion of the heated oxygen sensor has a zirconia element which is used to detect oxygen concentration in the exhaust. If the zirconia element is at the proper temperature and the difference of the oxygen concentration between the inside and outside surface of the sensor is large, the zirconia element will generate voltage signals. In order to increase the oxygen concentration detecting capacity in the zirconia element, the ECM supplements the heat from the exhaust with the heat from the heating element inside the sensor. When current in the sensor is out of the standard operating range, the ECM interprets this as a fault in the heated oxygen sensor and sets a DTC.

CAUTION / NOTICE / HINT

HINT:

Sensor 2 refers to the sensor mounted behind the Three-Way Catalytic Converter (TWC) and is located far from the engine assembly.


HINT:

Read freeze frame data using an intelligent tester. Freeze frame data records the engine conditions when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE)
A062378E55
1.438,1.406 1.177,1.885 false 1.969,1.375 2.208,1.885 false 1.438,0.823 1.552,1.021 0.115,0.198 10 false 2 1.865,0.823 1.979,1.021 0.115,0.198 10 false 1 1.438,1.229 1.552,1.427 0.115,0.198 10 false 4 1.865,1.229 1.979,1.427 0.115,0.198 10 false 3 2.281,0.271 2.76,0.469 0.479,0.198 10 false HT1B 0.948,0.292 1.25,0.521 0.302,0.229 10 false +B 2.281,1.844 2.719,2.042 0.438,0.198 10 false OX1B 0.927,1.844 1.146,2.042 0.219,0.198 10 false E2

a.

Disconnect the heated oxygen sensor connector.


b.

Measure the resistance of the heated oxygen sensor.

Standard resistance:
Tester Connection Condition Specified Condition
1 (HT1B) - 2 (+B) 20°C (68°F) 11 to 16 Ω
1 (HT1B) - 4 (E2) Always 10 kΩ or higher



c.

Reconnect the heated oxygen sensor connector.


Result:
Proceed to
OK
NG



OK

2.INSPECT NO.2 INTEGRATION RELAY (EFI RELAY)

NG

2.INSPECT NO.2 INTEGRATION RELAY (EFI RELAY)
a.

Inspect the NO. 2 integration relay (Click hereEngine / Hybrid System>1BZ-FPE (ENGINE CONTROL)>RELAY>ON-VEHICLE INSPECTION).


Result:
Proceed to
OK
NG



OK

3.INSPECT ECM (HT1B VOLTAGE)

NG

REPLACE NO.2 INTEGRATION RELAY

3.INSPECT ECM (HT1B VOLTAGE)
A177838E02
0.76,1.771 1.135,1.99 0.375,0.219 1.385,0.99 1.719,0.531 true 0.427,1 0.75,0.542 true 0.802,0.344 1.25,0.521 0.448,0.177 10 false E01 (-) 1.771,0.344 2.396,0.521 0.625,0.177 10 false HT1B (+) 0.833,1.792 1.208,1.99 0.375,0.198 10 false B76

a.

Turn the ignition switch to ON.


b.

Measure the voltage of the ECM connector.

Standard voltage:
Tester Connection Condition Specified Condition
B76-1 (HT1B) - B76-13 (E01) Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - ECM, EFI MAIN RELAY)

NG

4.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - ECM, EFI MAIN RELAY)
a.

Disconnect the heated oxygen sensor connector.


b.

Disconnect the ECM connector.


c.

Remove the NO. 2 integration relay from the relay block No. 2.


d.

Disconnect the NO. 2 integration relay connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
A62-1 (HT1B) - B76-1 (HT1B) Always Below 1Ω
A62-2 (+B) - 2D-4 Always Below 1 Ω
A62-1 (HT1B) or B76-1 (HT1B) - Body ground Always 10 kΩ or higher
A62-2 (+B) or 2D-4 - Body ground Always 10 kΩ or higher



f.

Reconnect the NO. 2 integration relay connector.


g.

Reinstall the integration relay.


h.

Reconnect the ECM connector.


i.

Reconnect the sensor connector.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR