Home › Engine / Hybrid System › N04C-UH (ENGINE CONTROL) › ECD SYSTEM
RM2850E _51 Engine / Hybrid System _073137 N04C-UH ENGINE CONTROL _0355844 ECD SYSTEM C

N04C-UH ENGINE CONTROL  ECD SYSTEM  P0087  Fuel Rail / System Pressure - Too Low  P0190  Fuel Rail Pressure Sensor Circuit  P0192  Fuel Rail Pressure Sensor Circuit Low Input  P0193  Fuel Rail Pressure Sensor Circuit High Input  


DESCRIPTION

The fuel pressure sensor, mounted on the common rail, converts the fuel pressure into an electric signal and outputs the signal to the ECM. Based on the signal from the fuel pressure sensor, the ECM controls the injection or supply pump (suction control valve) and keeps the internal fuel pressure of the common rail at the target fuel pressure.

DTC No. DTC Detection Condition Trouble Area
P0087 Conditions (a), (b) and (c) are met 10 times with engine speed 600 rpm or more:
(1 trip detection logic)
(a) Battery voltage: 8 V or more
(b) Fuel quantity: 28 mm3/st or more
(c) Amount of change in fuel pressure applied to common rail: 0.1 MPa or less
·

Open or short in fuel pressure sensor circuit

·

Fuel pressure sensor (common rail assembly)

·

ECM


P0190 Conditions (a) and (b) continue for 1 second or more:
(1 trip detection logic)
(a) Ignition switch ON
(b) Open or short in fuel pressure sensor circuit
·

Open or short in fuel pressure sensor circuit

·

Fuel pressure sensor (common rail assembly)

·

ECM


P0192 Condition (a) continues for 1 second:
(1 trip detection logic)
(a) Fuel pressure sensor output voltage is 0.55 V or less
·

Open or short in fuel pressure sensor circuit

·

Fuel pressure sensor (common rail assembly)

·

ECM


P0193 Condition (a) continues for 1 second:
(1 trip detection logic)
(a) Fuel pressure sensor output voltage is 4.9 V or more
·

Open or short in fuel pressure sensor circuit

·

Fuel pressure sensor (common rail assembly)

·

ECM



HINT:
·

If the vehicle runs out of fuel, letting the ECM determine the fuel pressure has decreased, DTC P0192 may be output.

·

When DTC P0087, P0190, P0192 and/or P0193 are set, check the internal fuel pressure of the common rail by entering the following menus on the intelligent tester: Powertrain / Engine and ECT / Data List / Fuel Press.


Engine Speed Fuel Pressure
Approximately. 0 kPa (0 kg/cm2, 0 psi) or more Short in PCR1 and E2 terminal
190000 kPa (1937 kg/cm2, 27557 psi) or more
·

Short in PCR1 and VC circuit

·

Open in PCR1 circuit

·

Open in E2 circuit




WIRING DIAGRAM

A185064E02
0.438,2.438 0.75,2.615 0.313,0.177 10 false B92 0.438,2.594 3.438,2.823 3,0.229 10 false Fuel Pressure Sensor (Common Rail Assembly) 5.896,2.458 6.25,2.688 0.354,0.229 10 false ECM 5.156,1.75 5.333,1.906 0.177,0.156 10 false 28 5.156,1.292 5.333,1.448 0.177,0.156 10 false 26 5.167,0.813 5.344,0.969 0.177,0.156 10 false 18 1.833,1.906 2.073,2.115 0.24,0.208 10 false E1 1.656,1.448 2.073,1.656 0.417,0.208 10 false PCR1 1.76,0.979 2.104,1.177 0.344,0.198 10 false VC1 5.438,1.917 5.76,2.104 0.323,0.188 10 false E2 5.438,1.458 5.885,1.656 0.448,0.198 10 false PCR1 5.438,0.99 5.729,1.156 0.292,0.167 10 false VC 2.156,1.802 2.417,1.99 0.26,0.188 10 false 1 2.156,1.333 2.417,1.531 0.26,0.198 10 false 2 2.156,0.865 2.406,1.052 0.25,0.188 10 false 3 5.104,1.906 5.417,2.104 0.313,0.198 10 false B59 5.104,1.458 5.417,1.646 0.313,0.188 10 false B59 5.104,0.979 5.427,1.167 0.323,0.188 10 false B59

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>N04C-UH (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click here Engine / Hybrid System>N04C-UH (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).


HINT:
·

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.

·

If different DTCs that are related to a different system are output simultaneously while terminal E2 is used as a ground terminal, terminal E2 may be open.



PROCEDURE

1.INSPECT ECM (OUTPUT VOLTAGE)
a.
A224395E24
0.51,0.198 0.938,0.448 0.427,0.25 0.531,1.531 1,0.948 true 1.229,1.542 1,1.031 true 0.094,0.083 0.323,0.292 0.229,0.208 10 false *a 0.604,0.25 0.906,0.427 0.302,0.177 10 false B59 0.229,1.563 0.792,1.771 0.563,0.208 10 false 18 (VC) 1.094,1.573 1.635,1.802 0.542,0.229 10 false 28 (E2)

Turn the ignition switch to ON.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
B59-18 (VC) - B59-28 (E2) Ignition switch ON 4.5 to 5.5 V


Text in Illustration
*a Component with harness connected
(ECM)


Result:
Proceed to
OK
NG



OK

2.INSPECT ECM (PCR1 VOLTAGE)

NG

2.INSPECT ECM (PCR1 VOLTAGE)
a.
A224395E25
0.51,0.198 0.938,0.448 0.427,0.25 0.323,1.531 0.563,0.958 true 1.229,1.542 1,1.031 true 0.094,0.083 0.323,0.292 0.229,0.208 10 false *a 0.604,0.25 0.906,0.427 0.302,0.177 10 false B59 0.094,1.573 0.833,1.792 0.74,0.219 10 false 26 (PCR1) 1.094,1.573 1.635,1.802 0.542,0.229 10 false 28 (E2)

Start the engine.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
B59-26 (PCR1) - B59-28 (E2) Idling 1.3 to 1.7 V


Text in Illustration
*a Component with harness connected
(ECM)


Result:
Proceed to
OK
NG



OK

NG

3.CHECK HARNESS AND CONNECTOR (ECM - FUEL PRESSURE SENSOR)
3.CHECK HARNESS AND CONNECTOR (ECM - FUEL PRESSURE SENSOR)
a.

Disconnect the ECM connector.


b.

Disconnect the fuel pressure sensor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B59-26 (PCR1) - B92-2 (PCR1) Always Below 1 Ω
B59-18 (VC) - B92-3 (VC1) Always Below 1 Ω
B59-28 (E2) - B92-1 (E1) Always Below 1 Ω
B59-26 (PCR1) or B92-2 (PCR1) - Body ground Always 10 kΩ or higher
B59-18 (VC) or B92-3 (VC1) - Body ground Always 10 kΩ or higher



d.

Reconnect the fuel pressure sensor connector.


e.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

REPLACE COMMON RAIL ASSEMBLY (FUEL PRESSURE SENSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR