Home › Engine / Hybrid System › N04C-UH (ENGINE CONTROL) › ECD SYSTEM
RM2850E _51 Engine / Hybrid System _073137 N04C-UH ENGINE CONTROL _0355844 ECD SYSTEM C

N04C-UH ENGINE CONTROL  ECD SYSTEM  P0088  Fuel Rail / System Pressure - Too High  P0627  Fuel Pump Control Circuit / Open  P1229  Fuel Pump System  


DESCRIPTION

The injection or supply pump assembly is a single-type pump and has a circuit for fuel suction that achieves high pressure force feed and reduction of driving torque, and for force feed process. The ECM controls the suction control valve, which operates fuel suction by the plunger in the process of suction.

When the internal fuel pressure of the common rail assembly exceeds the target pressure, the pressure limiter on the common rail assembly starts operating to control the internal fuel pressure of the common rail assembly.

DTC No. DTC Detection Condition Trouble Area
P0088 Conditions (a) and (b) are met 4 times or more:
(1 trip detection logic)
(a) Ignition switch ON
(b) Internal fuel pressure of the common rail: 212 MPa (2162 kg/cm2, 30748 psi) or more
·

Injection or supply pump assembly (suction control valve)

·

Short in injection or supply pump assembly (suction control valve) circuit

·

Common rail assembly

·

ECM


P0627 Open or short in suction control valve circuit for more than 0.5 seconds
(1 trip detection logic)
·

Injection or supply pump assembly (suction control valve)

·

Open or short in injection or supply pump assembly (suction control valve) circuit

·

ECM


P1229 Fuel over-feed:
Internal fuel pressure is beyond target fuel pressure despite ECM closing suction control valve
(1 trip detection logic)
·

Injection or supply pump assembly (suction control valve)

·

Open or short in injection or supply pump assembly (suction control valve) circuit

·

Common rail assembly

·

ECM



WIRING DIAGRAM

A257492E02
0.469,1.479 0.823,1.667 0.354,0.188 10 false B52 0.458,1.646 2.958,2.031 2.5,0.385 10 false Suction Control Valve (Built into Injection or Supply Pump Assembly) 1.292,0.417 1.708,0.604 0.417,0.188 10 false SCV+ 1.323,1 1.708,1.177 0.385,0.177 10 false SCV- 1.792,0.396 1.917,0.573 0.125,0.177 10 false 1 1.802,1 1.917,1.188 0.115,0.188 10 false 2 5.865,2.156 6.271,2.375 0.406,0.219 10 false ECM 5.583,0.531 6.031,0.75 0.448,0.219 10 false PCV+ 5.573,1.115 5.979,1.344 0.406,0.229 10 false PCV- 5.573,1.729 5.813,1.958 0.24,0.229 10 false E1 5.25,0.302 5.427,0.448 0.177,0.146 10 false 2 5.188,0.531 5.5,0.729 0.313,0.198 10 false B59 5.25,0.906 5.448,1.094 0.198,0.188 10 false 1 5.188,1.125 5.5,1.333 0.313,0.208 10 false B59 5.26,1.521 5.438,1.688 0.177,0.167 10 false 7 5.188,1.75 5.5,1.948 0.313,0.198 10 false B60

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>N04C-UH (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click here Engine / Hybrid System>N04C-UH (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).

·

After replacing the injection or supply pump assembly, the ECM needs initialization (Click here Engine / Hybrid System>N04C-UH (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).



HINT:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK OTHER DTC OUTPUT
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / DTC.


e.

Read DTCs.


Result:
Result Proceed to
DTC P0180, P0182, P0183, P190, P191, P192, P193 or P0200 is not output A
DTC P0180, P0182, P0183, P190, P191, P192, P193 or P0200 is output B



A

2.INSPECT INJECTION OR SUPPLY PUMP ASSEMBLY (SUCTION CONTROL VALVE)

B

2.INSPECT INJECTION OR SUPPLY PUMP ASSEMBLY (SUCTION CONTROL VALVE)
a.
A153586E12
1.021,0.365 1.5,0.656 true 0.073,0.063 0.396,0.26 0.323,0.198 10 false *a 0.792,0.219 1.021,0.417 0.229,0.198 10 false *1

Disconnect the suction control valve connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 1.9 to 2.3 Ω


Text in Illustration
*1 Suction Control Valve
*a Component without harness connected
(Injection or Supply Pump Assembly)


Result:
Proceed to
OK
NG



OK

3.CHECK DTC OUTPUT

NG

REPLACE INJECTION OR SUPPLY PUMP ASSEMBLY

3.CHECK DTC OUTPUT
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / DTC.


e.

Read DTCs.


Result:
Result Proceed to
DTC P0088 and/or P1229 A
DTC P0627 B



A

4.INSPECT INJECTION OR SUPPLY PUMP ASSEMBLY (SUCTION CONTROL VALVE)

B

9.CHECK HARNESS AND CONNECTOR (SUCTION CONTROL VALVE - ECM)
4.INSPECT INJECTION OR SUPPLY PUMP ASSEMBLY (SUCTION CONTROL VALVE)
a.

Disconnect the suction control valve connector and then start the engine.

OK:

Engine does not start.



Result:
Proceed to
OK
NG



OK

5.READ VALUE USING INTELLIGENT TESTER (TARGET PUMP SCV CURRENT)

NG

REPLACE INJECTION OR SUPPLY PUMP ASSEMBLY

5.READ VALUE USING INTELLIGENT TESTER (TARGET PUMP SCV CURRENT)
a.

Connect the intelligent tester to the DLC3.


b.

Start the engine.


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Target Pump SCV Current.


e.

Read the value.

Standard:
Engine Speed Result
Idling 1350 to 2200 mA



Result:
Proceed to
OK
NG



OK

6.READ VALUE USING INTELLIGENT TESTER (FUEL PRESS)

NG

REPLACE INJECTION OR SUPPLY PUMP ASSEMBLY

6.READ VALUE USING INTELLIGENT TESTER (FUEL PRESS)
a.

Connect the intelligent tester to the DLC3.


b.

Start the engine.


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Fuel Press.


e.

Check that the internal fuel pressure of the common rail is within the specification below.

Standard:
Engine Speed Fuel Press
Idling Approximately 25000 to 35000 kPa



Result:
Result Proceed to
NG A
OK B



A

7.CHECK HARNESS AND CONNECTOR (SUCTION CONTROL VALVE - ECM)

B

9.CHECK HARNESS AND CONNECTOR (SUCTION CONTROL VALVE - ECM)
7.CHECK HARNESS AND CONNECTOR (SUCTION CONTROL VALVE - ECM)
a.

Check the wire harness and connector.

i.

Disconnect the suction control valve connector.


ii.

Disconnect the ECM connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Standard Resistance Condition Specified Condition
B59-2 (PCV+) - B52-1 (SCV+) Always Below 1 Ω
B59-1 (PCV-) - B52-2 (SCV-) Always Below 1 Ω
B59-2 (PCV+) or B52-1 (SCV+) - Body ground Always 10 kΩ or higher
B59-1 (PCV-) or B52-2 (SCV-) - Body ground Always 10 kΩ or higher




Result:
Proceed to
OK
NG



OK

8.READ VALUE USING INTELLIGENT TESTER (FUEL PRESS)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.READ VALUE USING INTELLIGENT TESTER (FUEL PRESS)
a.

Connect the intelligent tester to the DLC3.


b.

Start the engine.


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Fuel Press.


e.

Wiggle the fuel pressure sensor connector and check that the fuel pressure reading does not change.

OK:

The fuel pressure reading does not change.



Result:
Proceed to
OK
NG



OK

REPLACE INJECTION OR SUPPLY PUMP ASSEMBLY

NG

REPLACE COMMON RAIL ASSEMBLY

9.CHECK HARNESS AND CONNECTOR (SUCTION CONTROL VALVE - ECM)
a.

Check the wire harness and connector.

i.

Disconnect the suction control valve connector.


ii.

Disconnect the ECM connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Standard Resistance Condition Specified Condition
B59-2 (PCV+) - B52-1 (SCV+) Always Below 1 Ω
B59-1 (PCV-) - B52-2 (SCV-) Always Below 1 Ω
B59-2 (PCV+) or B52-1 (SCV+) - Body ground Always 10 kΩ or higher
B59-1 (PCV-) or B52-2 (SCV-) - Body ground Always 10 kΩ or higher




Result:
Proceed to
OK
NG



OK

10.INSPECT ECM (PCV+ AND PCV- OUTPUT VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.INSPECT ECM (PCV+ AND PCV- OUTPUT VOLTAGE)
a.
A151976E14
0.521,0.729 0.938,0.99 0.417,0.26 1.135,0.729 1.552,0.99 0.417,0.26 1.115,1.25 1.708,1.969 true 0.958,1.25 1.073,1.969 true 0.885,1.24 0.406,1.958 true 0.594,0.781 0.917,0.948 0.323,0.167 10 false B59 1.229,0.781 1.552,0.969 0.323,0.188 10 false B60 1.708,1.99 2.219,2.188 0.51,0.198 10 false 7 (E1) 0.813,2 1.438,2.208 0.625,0.208 10 false 1 (PCV-) 0.198,3.927 0.625,4.115 0.427,0.188 10 false PCV- 0.104,1.99 0.76,2.219 0.656,0.229 10 false 2 (PCV+) 0.198,3.615 0.635,3.792 0.438,0.177 10 false PCV+ 1.26,4.323 2.229,4.542 0.969,0.219 10 false 5 msec./DIV. 2.625,3.542 3.229,3.75 0.604,0.208 10 false 5 V/DIV. 2.625,3.875 3.177,4.115 0.552,0.24 10 false 1 V/DIV. 0.167,0.135 0.396,0.333 0.229,0.198 10 false *a

While cranking or idling the engine, check the waveform of the ECM connector using an oscilloscope.

OK:
Tester Connection Condition Tool Setting Specified Condition
B59-2 (PCV+) - B60-7 (E1) Idling or cranking with warm engine 5 V/DIV., 5 msec./DIV. Correct waveform appears as shown
B59-1 (PCV-) - B60-7 (E1) Idling or cranking with warm engine 1 V/DIV., 5 msec./DIV. Correct waveform appears as shown


Text in Illustration
*a Component with harness connected
(ECM)


Result:
Proceed to
OK
NG



OK

11.PERFORM INITIALIZATION (INJECTION OR SUPPLY PUMP ASSEMBLY)

NG

11.PERFORM INITIALIZATION (INJECTION OR SUPPLY PUMP ASSEMBLY)

Result:
Proceed to
NEXT



NEXT

12.CHECK WHETHER DTC OUTPUT RECURS
12.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Clear the DTCs.


e.

Enter the following menus: Powertrain / Engine and ECT / DTC.


f.

Read the DTCs.


Result:
Result Proceed to
P0088, P0627 or P1229 is output A
P0088, P0627 or P1229 is not output B



A

REPLACE INJECTION OR SUPPLY PUMP ASSEMBLY

B

END