Home › Engine / Hybrid System › N04C-UH (ENGINE CONTROL) › ECD SYSTEM
RM2850E _51 Engine / Hybrid System _073137 N04C-UH ENGINE CONTROL _0355844 ECD SYSTEM C

N04C-UH ENGINE CONTROL  ECD SYSTEM  P0100  Mass or Volume Air Flow Circuit  P0102  Mass or Volume Air Flow Circuit Low Input  P0103  Mass or Volume Air Flow Circuit High Input  


DESCRIPTION

The mass air flow meter sub-assembly uses a platinum hot wire. The hot wire mass air flow meter sub-assembly consists of a platinum hot wire, thermistor and a control circuit installed in a plastic housing. The hot wire mass air flow meter sub-assembly works on the principle that the hot wire and thermistor located in the intake air bypass of the housing detect any changes in the intake air temperature.

The hot wire is maintained at the set temperature by controlling current flow through the hot wire. This current flow is then measured as the output voltage of the mass air flow meter sub-assembly.

The circuit is constructed so that the platinum hot wire and thermistor provide a bridge circuit with the power transistor controlled so that the potential of A and B remains equal to maintain the set temperature.

A153590E05
1.375,0.344 1.542,0.344 1.542,0.344 1.698,1.635 true 2.688,0.396 2.5,0.396 2.5,0.396 1.927,1.625 false 3.75,0.906 3.875,0.906 3.875,0.906 4.25,1.344 true 4.542,1.688 3.802,2.24 3.802,2.24 3.802,2.365 true 1.979,0.396 2.229,0.563 0.25,0.167 10 false +B 2.031,1.531 2.146,1.698 0.115,0.167 10 false B 1.51,1.521 1.625,1.688 0.115,0.167 10 false A 3.24,2.396 4.427,2.563 1.188,0.167 10 false Platinum Hot Wire 2.74,0.323 3.927,0.49 1.188,0.167 10 false Platinum Hot Wire 2.594,1.781 3.573,1.948 0.979,0.167 10 false Output Voltage 4.906,0.271 7.135,0.458 2.229,0.188 10 false Mass Air Flow Meter Sub-assembly 2.458,0.823 3.75,1.167 1.292,0.344 10 false Temperature Sensor (Thermistor) 0.073,0.271 1.344,0.635 1.271,0.365 10 false Temperature Sensor (Thermistor)

DTC No. DTC Detection Condition Trouble Area
P0100 Open or short in mass air flow meter sub-assembly circuit for more than 3 seconds with engine speed at 4000 rpm or less
(1 trip detection logic)
·

Open or short in mass air flow meter sub-assembly circuit

·

Mass air flow meter sub-assembly

·

ECM


P0102 Open or short in mass air flow meter sub-assembly circuit for more than 3 seconds with engine speed at 4000 rpm or less
(1 trip detection logic)
·

Open or short in mass air flow meter sub-assembly circuit

·

Mass air flow meter sub-assembly

·

ECM


P0103 Open or short in mass air flow meter sub-assembly circuit for more than 3 seconds with engine speed at 4000 rpm or less
(1 trip detection logic)
·

Open or short in mass air flow meter sub-assembly circuit

·

Mass air flow meter sub-assembly

·

ECM



HINT:

When DTC P0100, P0102 or P0103 is detected, check the mass air flow ratio by entering the following menus on the intelligent tester: Powertrain / Engine and ECT / Data List / MAF.

Mass Air Flow Rate (gm/s) Malfunction
Approx. 0.0
·

Open in mass air flow meter sub-assembly power source circuit

·

Open or short in VG circuit


160.1 or more Open in EVG circuit


WIRING DIAGRAM

A398541E03
1.625,1.49 1.938,1.688 0.313,0.198 10 false 2D 2.781,0.719 3.094,0.917 0.313,0.198 10 false 2D 2.771,1.063 3.083,1.26 0.313,0.198 10 false 2D 1.01,0.719 1.323,0.917 0.313,0.198 10 false 2E 1.323,0.865 2.052,1.063 0.729,0.198 10 false EFI-MAIN 2.177,1.427 2.906,1.625 0.729,0.198 10 false EFI 0.583,0.875 1.313,1.073 0.729,0.198 10 false P/I 0.385,1.719 1.427,1.927 1.042,0.208 10 false R/B NO. 2-B 0.375,2.302 1.417,2.51 1.042,0.208 10 false FL MAIN 1.052,3.042 2.094,3.25 1.042,0.208 10 false Battery 1.792,1.729 3.26,1.938 1.469,0.208 10 false No. 2 Integration Relay 3.156,0.844 3.885,1.042 0.729,0.198 10 false EFI NO. 3 3.823,1.938 4.135,2.135 0.313,0.198 10 false B50 3.813,2.094 5.135,2.458 1.323,0.365 10 false Mass Air Flow Meter Sub-assembly 5.854,2.583 6.583,2.781 0.729,0.198 10 false MREL 5.875,1.427 6.25,1.604 0.375,0.177 10 false EVG 5.875,0.917 6.604,1.115 0.729,0.198 10 false VG 4.656,1.396 5.385,1.594 0.729,0.198 10 false E2G 4.76,0.896 5.49,1.094 0.729,0.198 10 false VG 3.865,0.604 4.594,0.802 0.729,0.198 10 false +B 1.552,1.281 1.708,1.479 0.156,0.198 10 false 3 3.667,0.604 3.823,0.802 0.156,0.198 10 false 1 5.083,1.396 5.24,1.594 0.156,0.198 10 false 2 2.823,0.5 2.979,0.698 0.156,0.198 10 false 4 2.823,0.896 2.979,1.094 0.156,0.198 10 false 2 1.063,0.521 1.219,0.719 0.156,0.198 10 false 1 5.073,0.927 5.229,1.125 0.156,0.198 10 false 3 5.438,1.031 5.865,1.229 0.427,0.198 10 false B60 5.438,1.531 5.917,1.729 0.479,0.198 10 false B60 5.448,2.802 5.76,3 0.313,0.198 10 false A54 5.479,0.854 5.698,1.031 0.219,0.177 10 false 24 5.479,1.323 5.698,1.5 0.219,0.177 10 false 32 5.458,2.594 5.677,2.771 0.219,0.177 10 false 13 6.188,3.302 6.917,3.5 0.729,0.198 10 false ECM

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of this circuits related to this system before performing the following procedure.

·

After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>N04C-UH (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click here Engine / Hybrid System>N04C-UH (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).



HINT:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (MAF)
a.

Connect the intelligent tester to the DLC3.


b.

Start the engine.


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / MAF.


e.

Read the value.

Result:
Mass Air Flow Rate (gm/s) Proceed to
0.0 A
160.1 or more B
Between 1.6 and 160.0* C


HINT:

*: The value should change when the throttle valve is opened or closed.




A

2.CHECK MASS AIR FLOW METER SUB-ASSEMBLY (POWER SOURCE)

B

4.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)

C

2.CHECK MASS AIR FLOW METER SUB-ASSEMBLY (POWER SOURCE)
a.
A084809E27
1.479,0.427 1.885,0.677 0.406,0.25 0.958,1.792 1.281,1.51 true 0.146,0.125 0.385,0.323 0.24,0.198 10 false *1 1.563,0.458 1.896,0.656 0.333,0.198 10 false B50 0.479,1.74 0.979,1.938 0.5,0.198 10 false +B (+)

Disconnect the mass air flow meter sub-assembly connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
B50-1 (+B) - Body ground Ignition switch ON 11 to 14 V


Text in Illustration
*1 Front view of wire harness connector
(to Mass Air Flow Meter Sub-assembly)


d.

Reconnect the mass air flow meter sub-assembly connector.


Result:
Proceed to
OK
NG



OK

3.INSPECT ECM (VG VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - NO. 2 INTEGRATION RELAY)

3.INSPECT ECM (VG VOLTAGE)
a.
A224395E26
1.25,0.208 1.677,0.458 0.427,0.25 1.177,1.542 1.417,1.031 true 2.042,1.573 1.406,0.948 true 0.094,0.083 0.323,0.292 0.229,0.208 10 false *a 1.333,0.26 1.635,0.438 0.302,0.177 10 false B60 0.906,1.594 1.646,1.813 0.74,0.219 10 false 32 (EVG) 1.833,1.573 2.417,1.802 0.583,0.229 10 false 24 (VG)

Start the engine.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
B60-24 (VG) - B60-32 (EVG) Engine idling 1.5 to 1.9 V
B60-24 (VG) - B60-32 (EVG) Engine speed at 3000 rpm 3.0 to 4.0 V


Text in Illustration
*a Component with harness connected
(ECM)

HINT:

The A/C switch should be turned off.



Result:
Proceed to
OK
NG



OK

NG

4.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)
4.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)
a.

Disconnect the mass air flow meter sub-assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B50-3 (FG) - B60-24 (VG) Always Below 1 Ω
B50-2 (E2G) - B60-32 (EVG) Always Below 1 Ω
B50-3 (FG) or B60-24 (VG) - Body ground Always 10 kΩ or higher



d.

Reconnect the mass air flow meter sub-assembly connector.


e.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

REPLACE MASS AIR FLOW METER SUB-ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR