Home › Engine / Hybrid System › N04C-UH (ENGINE CONTROL) › ECD SYSTEM
RM2850E _51 Engine / Hybrid System _073137 N04C-UH ENGINE CONTROL _0355844 ECD SYSTEM C

N04C-UH ENGINE CONTROL  ECD SYSTEM  P0105  Manifold Absolute Pressure / Barometric Pressure Circuit  P0107  Manifold Absolute Pressure / Barometric Pressure Circuit Low Input  P0108  Manifold Absolute Pressure / Barometric Pressure Circuit High Input  


DESCRIPTION

By a built-in sensor unit, manifold absolute pressure sensor detects the intake manifold pressure as a voltage. The ECM then determines the basic injection duration and basic ignition advance angle based on this voltage.

Since the manifold absolute pressure sensor does not use the atmospheric pressure as a criterion, but senses the absolute pressure inside the intake manifold (the pressure in proportion to the preset absolute vacuum 0), it is not influenced by fluctuations in the atmospheric pressure due to high altitude and other factors. This permits it to control the air fuel ratio at the proper level under all conditions.

A006532E21
0.469,0.448 0.604,0.646 0.135,0.198 10 false V 0.073,0.073 0.625,0.271 0.552,0.198 10 false Voltage 0.375,0.813 0.635,1.01 0.26,0.198 10 false 4.5 0.24,1.906 0.635,2.083 0.396,0.177 10 false 0.345 1.021,2.323 1.25,2.521 0.229,0.198 10 false 93 2.323,2.323 2.604,2.521 0.281,0.198 10 false 370 2.917,2.01 3.26,2.365 0.344,0.354 10 false kPa (abs) 2.885,2.563 3.375,2.76 0.49,0.198 10 false mmHg 2.896,2.875 3.385,3.083 0.49,0.208 10 false (in.Hg) 2.292,2.708 2.781,2.906 0.49,0.198 10 false 2,775 2.323,2.885 2.708,3.083 0.385,0.198 10 false (109) 0.854,2.708 1.26,2.896 0.406,0.188 10 false 697.6 0.833,2.865 1.281,3.063 0.448,0.198 10 false (27.5) 1.281,3.063 2.135,3.24 0.854,0.177 10 false Air Pressure

DTC No. DTC Detection Condition Trouble Area
P0105 After engine is started, condition (a) continues for more than 2.0 seconds
(1 trip detection logic)
(a) Open or short in manifold absolute pressure sensor circuit for 0.5 seconds or more
·

Open or short in manifold absolute pressure sensor circuit

·

Manifold absolute pressure sensor

·

ECM


P0107 After engine is started, condition (a) continues for more than 2.0 seconds
(1 trip detection logic)
(a) Open or short in manifold absolute pressure sensor circuit for 0.5 seconds or more
·

Open or short in manifold absolute pressure sensor circuit

·

Manifold absolute pressure sensor

·

ECM


P0108 After engine is started, condition (a) continues for more than 2.0 seconds
(1 trip detection logic)
(a) Open or short in manifold absolute pressure sensor circuit for 0.5 seconds or more
·

Open or short in manifold absolute pressure sensor circuit

·

Manifold absolute pressure sensor

·

ECM



HINT:

When DTC P0105, P0107 or P0108 is detected, check the intake manifold pressure by entering the following menus on the intelligent tester: Powertrain / Engine and ECT / Data List / MAP.

MAP (kPa) Malfunction
Approximately 0 E2, PIM circuit short
255
·

PIM, VC circuit short

·

PIM circuit open

·

E2 circuit open




WIRING DIAGRAM

A198999E25
5.198,1.938 5.427,2.083 0.229,0.146 10 false 28 5.146,2.135 5.427,2.302 0.281,0.167 10 false B59 5.188,1.427 5.427,1.594 0.24,0.167 10 false 28 5.146,1.625 5.427,1.813 0.281,0.188 10 false B60 5.198,0.917 5.427,1.063 0.229,0.146 10 false 18 1.635,2.135 1.802,2.313 0.167,0.177 10 false E 1.479,1.615 1.823,1.792 0.344,0.177 10 false PIM 1.552,1.104 1.833,1.292 0.281,0.188 10 false VC 5.49,2.146 5.802,2.344 0.313,0.198 10 false E2 5.49,1.635 5.823,1.833 0.333,0.198 10 false PIM 5.49,1.094 5.854,1.281 0.365,0.188 10 false VC 5.156,1.094 5.448,1.281 0.292,0.188 10 false B59 5.906,2.938 6.302,3.146 0.396,0.208 10 false ECM 0.521,2.583 0.927,2.76 0.406,0.177 10 false B18 0.521,2.771 2.792,2.99 2.271,0.219 10 false Manifold Absolute Pressure Sensor 1.896,2.031 2.031,2.208 0.135,0.177 10 false 1 1.896,1.521 2.042,1.698 0.146,0.177 10 false 2 1.896,0.99 2.031,1.167 0.135,0.177 10 false 3

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>N04C-UH (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click here Engine / Hybrid System>N04C-UH (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).


HINT:
·

If DTCs that are related to different systems are output simultaneously while terminal E2 is used as a ground terminal, terminal E2 may have an open circuit.

·

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (MANIFOLD ABSOLUTE PRESSURE)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / MAP.


e.

Read the value.

OK:

Same value as the actual atmospheric pressure.


HINT:
·

Standard atmospheric pressure is 101 kPa. For every 100 m increase in altitude, pressure drops by 1 kPa. Varies by weather (high atmospheric pressure, low atmospheric pressure).

·

Also, check "Atmosphere Pressure" in the Data List.




Result:
Result Proceed to
NG A
OK B



A

2.INSPECT ECM (VC VOLTAGE)

B

2.INSPECT ECM (VC VOLTAGE)
a.
A224395E24
0.51,0.198 0.938,0.448 0.427,0.25 0.531,1.531 1,0.948 true 1.229,1.542 1,1.031 true 0.094,0.083 0.323,0.292 0.229,0.208 10 false *a 0.604,0.25 0.906,0.427 0.302,0.177 10 false B59 0.229,1.563 0.792,1.771 0.563,0.208 10 false 18 (VC) 1.094,1.573 1.635,1.802 0.542,0.229 10 false 28 (E2)

Turn the ignition switch to ON.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
B59-18 (VC) - B59-28 (E2) Ignition switch ON 4.5 to 5.5 V


Text in Illustration
*a Component with harness connected
(ECM)


Result:
Proceed to
OK
NG



OK

3.INSPECT ECM (PIM VOLTAGE)

NG

3.INSPECT ECM (PIM VOLTAGE)
a.
A224395E27
0.583,0.198 1,0.438 0.417,0.24 1.177,0.208 1.594,0.448 0.417,0.24 0.854,1.531 1,1.031 true 1.938,1.521 1.74,1.031 true 0.104,0.052 0.375,0.302 0.271,0.25 10 false *a 0.667,0.24 0.969,0.417 0.302,0.177 10 false B59 0.604,1.573 1.146,1.781 0.542,0.208 10 false 28 (E2) 1.688,1.573 2.333,1.771 0.646,0.198 10 false 28 (PIM) 1.271,0.25 1.573,0.427 0.302,0.177 10 false B60

Turn the ignition switch to ON.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
B60-28 (PIM) - B59-28 (E2) Negative pressure of 93 kPa [abs] (675 mmHg, 27.5 in.Hg) applied 0.2 to 0.5 V
B60-28 (PIM) - B59-28 (E2) Positive pressure of 150 kPa [abs] (1125 mmHg, 44 in.Hg) applied 1.0 to 1.4 V


Text in Illustration
*a Component with harness connected
(ECM)


Result:
Proceed to
OK
NG



OK

NG

4.CHECK HARNESS AND CONNECTOR (MANIFOLD ABSOLUTE PRESSURE SENSOR - ECM)
4.CHECK HARNESS AND CONNECTOR (MANIFOLD ABSOLUTE PRESSURE SENSOR - ECM)
a.

Disconnect the manifold absolute pressure sensor connector.


b.

Disconnect the ECM connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B18-2 (PIM) - B60-28 (PIM) Always Below 1 Ω
B18-3 (VC) - B59-18 (VC) Always Below 1 Ω
B18-1 (E) - B59-28 (E2) Always Below 1 Ω
B18-2 (PIM) or B60-28 (PIM) - Body ground Always 10 kΩ or higher
B18-3 (VC) or B59-18 (VC) - Body ground Always 10 kΩ or higher



d.

Reconnect the manifold absolute pressure sensor connector.


e.

Reconnect the ECM connectors.


Result:
Proceed to
OK
NG



OK

REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR