Home › Engine / Hybrid System › N04C-UH (ENGINE CONTROL) › ECD SYSTEM
RM2850E _51 Engine / Hybrid System _073137 N04C-UH ENGINE CONTROL _0355844 ECD SYSTEM C

N04C-UH ENGINE CONTROL  ECD SYSTEM  P0110  Intake Air Temperature Circuit  P0112  Intake Air Temperature Circuit Low Input  P0113  Intake Air Temperature Circuit High Input  


DESCRIPTION

The intake air temperature sensor is built into the mass air flow meter sub-assembly and senses the atmospheric temperature. A thermistor built in the sensor changes the resistance value according to the intake air temperature. The lower the atmospheric temperature is, the greater the thermistor resistance value is, and the higher the atmospheric temperature is, the lower the thermistor resistance value is (see Fig. 1).

The intake air temperature sensor is connected to the ECM. The 5 V power source voltage in the ECM is applied to the intake air temperature sensor from terminal THA via a resistor R. The resistor R and the intake air temperature sensor are connected in series. When the resistance value of the intake air temperature sensor changes in accordance with changes in the intake air temperature, the voltage at terminal THA also changes. Based on this signal, the ECM increases the fuel injection volume to improve driveability during cold engine operation.

A426790E01
1.667,2.042 1.917,1.521 1.917,1.521 2.073,1.521 true 1.417,0.198 2.115,0.417 0.698,0.219 10 false (Figure 1) 0.104,0.417 1.135,0.625 1.031,0.208 10 false Resistance kΩ 2.115,1.427 2.917,1.635 0.802,0.208 10 false Acceptable 1.354,4.198 2.771,4.406 1.417,0.208 10 false Temperature °C (°F) 0.552,0.771 0.76,0.958 0.208,0.188 10 false 30 0.552,0.938 0.76,1.125 0.208,0.188 10 false 20 0.542,1.24 0.75,1.427 0.208,0.188 10 false 10 0.615,1.552 0.76,1.74 0.146,0.188 10 false 5 0.615,1.792 0.76,1.979 0.146,0.188 10 false 3 0.615,1.969 0.76,2.156 0.146,0.188 10 false 2 0.615,2.26 0.76,2.448 0.146,0.188 10 false 1 0.5,3.292 0.76,3.49 0.26,0.198 10 false 0.1 0.5,2.969 0.76,3.167 0.26,0.198 10 false 0.2 0.5,2.792 0.76,2.99 0.26,0.198 10 false 0.3 0.5,2.563 0.76,2.76 0.26,0.198 10 false 0.5 0.854,3.656 1.115,3.854 0.26,0.198 10 false -20 1.219,3.656 1.406,3.833 0.188,0.177 10 false 0 1.531,3.667 1.719,3.844 0.188,0.177 10 false 20 1.823,3.667 2.01,3.844 0.188,0.177 10 false 40 2.135,3.667 2.323,3.844 0.188,0.177 10 false 60 2.49,3.667 2.677,3.844 0.188,0.177 10 false 80 2.802,3.667 3.083,3.854 0.281,0.188 10 false 100 0.854,3.813 1.146,4.01 0.292,0.198 10 false (-4) 1.156,3.813 1.448,4.01 0.292,0.198 10 false (32) 1.479,3.813 1.771,4.01 0.292,0.198 10 false (68) 1.75,3.813 2.146,4 0.396,0.188 10 false (104) 2.073,3.813 2.469,4 0.396,0.188 10 false (140) 2.417,3.813 2.813,4 0.396,0.188 10 false (176) 2.771,3.813 3.167,4 0.396,0.188 10 false (212)

DTC No. Proceed to DTC Detection Condition Trouble Area
P0110 Step 1 Open or short in intake air temperature sensor circuit for 0.5 seconds
(1 trip detection logic)
·

Open or short in intake air temperature sensor circuit

·

Intake air temperature sensor (built into mass air flow meter sub-assembly)

·

ECM


P0112 Step 4 Short in intake air temperature sensor circuit for 0.5 seconds
(1 trip detection logic)
·

Short in intake air temperature sensor circuit

·

Intake air temperature sensor (built into mass air flow meter sub-assembly)

·

ECM


P0113 Step2 Open in intake air temperature sensor circuit for 0.5 seconds
(1 trip detection logic)
·

Open in intake air temperature sensor circuit

·

Intake air temperature sensor (built into mass air flow meter sub-assembly)

·

ECM



HINT:

When DTC P0110, P0112 or P0113 is detected, check the intake air temperature by entering the following menus on the intelligent tester: Powertrain / Engine and ECT / Data List / Intake Air.

Temperature Displayed Malfunction
-40°C (-40°F) Open circuit
140°C (284°F) Short circuit


WIRING DIAGRAM

A199002E39
5.208,1.573 5.448,1.75 0.24,0.177 10 false 28 5.167,1.771 5.74,2.052 0.573,0.281 10 false B59 5.208,0.948 5.458,1.146 0.25,0.198 10 false 31 2.031,1.042 2.385,1.229 0.354,0.188 10 false THA 5.167,1.156 5.531,1.396 0.365,0.24 10 false B59 0.594,2.333 0.958,2.521 0.365,0.188 10 false B50 2.427,1.656 2.552,1.833 0.125,0.177 10 false 5 2.427,1.021 2.583,1.229 0.156,0.208 10 false 4 5.969,2.708 6.365,2.854 0.396,0.146 10 false ECM 0.594,2.5 3.104,2.865 2.51,0.365 10 false Intake Air Temperature Sensor (Built into Mass Air Flow Meter Sub-assembly) 6.198,0.688 6.469,0.854 0.271,0.167 10 false 5 V 6.125,0.917 6.271,1.073 0.146,0.156 10 false R 2.125,1.656 2.385,1.833 0.26,0.177 10 false E2 5.521,1.042 5.875,1.229 0.354,0.188 10 false THA 5.521,1.667 5.792,1.844 0.271,0.177 10 false E2

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>N04C-UH (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click here Engine / Hybrid System>N04C-UH (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).


HINT:
·

If DTCs that are related to different systems are output simultaneously while terminal E2 is used as a ground terminal, terminal E2 may have an open circuit.

·

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (INTAKE AIR TEMPERATURE)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air.


e.

Read the value.

OK:

Same value as the actual intake air temperature.


Result:
Result Proceed to
-40°C (-40°F) A
140°C (284°F) B
OK (same as actual intake air temperature) C


HINT:
·

If there is an open circuit, the intelligent tester indicates -40°C (-40°F).

·

If there is a short circuit, the intelligent tester indicates 140°C (284°F).





A

2.READ VALUE USING INTELLIGENT TESTER (CHECK FOR OPEN IN WIRE HARNESS)

B

4.READ VALUE USING INTELLIGENT TESTER (CHECK FOR SHORT IN WIRE HARNESS)

C

2.READ VALUE USING INTELLIGENT TESTER (CHECK FOR OPEN IN WIRE HARNESS)
a.
A153594E08
0.458,3.542 0.854,3.813 0.396,0.271 2.156,3.771 2.396,4.021 true 1.927,3.771 2.052,4.25 true 0.813,0.552 1.083,0.74 0.271,0.188 10 false *1 1.615,2.865 1.833,3.063 0.219,0.198 10 false *3 2.396,1.292 2.75,1.458 0.354,0.167 10 false THA 1.938,4.281 2.271,4.479 0.333,0.198 10 false THA 2.604,0.281 2.844,0.469 0.24,0.188 10 false *2 2.396,1.635 2.656,1.833 0.26,0.198 10 false E2 2.438,4.01 2.667,4.177 0.229,0.167 10 false E2 0.531,3.604 0.865,3.781 0.333,0.177 10 false B50

Disconnect the mass air flow meter sub-assembly connector.


b.

Connect terminals 4 and 5 of the mass air flow meter sub-assembly wire harness side connector.


c.

Connect the intelligent tester to the DLC3.


d.

Turn the ignition switch to ON.


e.

Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air.


f.

Read the value.

Standard:

140°C (284°F)


Text in Illustration
*1 Intake Air Temperature Sensor
*2 ECM
*3 Front view of wire harness connector
(to Mass Air Flow Meter Sub-assembly)


g.

Reconnect the mass air flow meter sub-assembly connector.


Result:
Proceed to
OK
NG



OK

REPLACE MASS AIR FLOW METER SUB-ASSEMBLY

NG

3.READ VALUE USING INTELLIGENT TESTER (CHECK FOR OPEN IN ECM)
3.READ VALUE USING INTELLIGENT TESTER (CHECK FOR OPEN IN ECM)
a.
A153595E07
0.604,2.75 1.021,3 0.417,0.25 0.958,3.49 1.104,3.969 true 0.802,3.51 0.573,4 true 0.833,0.604 1.104,0.813 0.271,0.208 10 false *1 0.24,2.323 0.479,2.521 0.24,0.198 10 false *3 2.406,1.292 2.76,1.458 0.354,0.167 10 false THA 0.385,4 0.74,4.167 0.354,0.167 10 false THA 2.656,0.281 2.906,0.469 0.25,0.188 10 false *2 2.417,1.625 2.646,1.792 0.229,0.167 10 false E2 1.063,4.021 1.354,4.219 0.292,0.198 10 false E2 0.677,2.792 0.969,2.969 0.292,0.177 10 false B59

Disconnect the mass air flow meter sub-assembly connector.


b.

Connect terminals THA and E2 of the ECM connector.

HINT:

Before checking, perform a visual and contact pressure check on the ECM connector.



c.

Connect the intelligent tester to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the tester on.


f.

Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air.


g.

Read the value.

Standard:

140°C (284°F)


Text in Illustration
*1 Intake Air Temperature Sensor
*2 ECM
*3 Component with harness connected
(ECM)


h.

Reconnect the mass air flow meter sub-assembly connector.


Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - MASS AIR FLOW METER SUB-ASSEMBLY)

NG

4.READ VALUE USING INTELLIGENT TESTER (CHECK FOR SHORT IN WIRE HARNESS)
a.
A083863E70
0.781,0.333 1.01,0.521 0.229,0.188 10 false *1 2.417,1.031 2.771,1.219 0.354,0.188 10 false THA 2.677,0.198 2.875,0.396 0.198,0.198 10 false *2 2.417,1.385 2.667,1.573 0.25,0.188 10 false E2

Disconnect the mass air flow meter sub-assembly connector.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the tester on.


e.

Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air.


f.

Read the value.

Standard:

-40°C (-40°F)


Text in Illustration
*1 Intake Air Temperature Sensor
*2 ECM


g.

Reconnect the mass air flow meter sub-assembly connector.


Result:
Proceed to
OK
NG



OK

REPLACE MASS AIR FLOW METER SUB-ASSEMBLY

NG

5.READ VALUE USING INTELLIGENT TESTER (CHECK FOR SHORT IN ECM)
5.READ VALUE USING INTELLIGENT TESTER (CHECK FOR SHORT IN ECM)
a.
A153596E07
0.552,2.979 0.927,3.219 0.375,0.24 0.99,4.042 1.292,4.271 true 0.802,4.031 0.51,4.344 true 0.813,0.552 1.042,0.781 0.229,0.229 10 false *1 0.25,2.281 0.49,2.49 0.24,0.208 10 false *3 2.396,1.281 2.75,1.448 0.354,0.167 10 false THA 0.229,4.313 0.583,4.479 0.354,0.167 10 false THA 2.635,0.26 2.844,0.479 0.208,0.219 10 false *2 2.396,1.625 2.625,1.792 0.229,0.167 10 false E2 1.333,4.219 1.604,4.406 0.271,0.188 10 false E2 0.615,3.01 0.917,3.188 0.302,0.177 10 false B59

Disconnect the mass air flow meter sub-assembly connector.


b.

Disconnect the ECM connector.


c.

Connect the intelligent tester to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the tester on.


f.

Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air.


g.

Read the value.

Standard:

-40°C (-40°F)


Text in Illustration
*1 Intake Air Temperature Sensor
*2 ECM
*3 Rear view of wire harness connector
(to ECM)


h.

Reconnect the mass air flow meter sub-assembly connector.


i.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - MASS AIR FLOW METER SUB-ASSEMBLY)

NG