Home › Engine / Hybrid System › N04C-UH (ENGINE CONTROL) › ECD SYSTEM
RM2850E _51 Engine / Hybrid System _073137 N04C-UH ENGINE CONTROL _0355844 ECD SYSTEM C

N04C-UH ENGINE CONTROL  ECD SYSTEM  P0115  Engine Coolant Temperature Circuit  P0117  Engine Coolant Temperature Circuit Low Input  P0118  Engine Coolant Temperature Circuit High Input  


DESCRIPTION

A thermistor is built into the Engine Coolant Temperature (ECT) sensor and changes its resistance value according to the ECT.

The structure of the sensor and connection to the ECM are the same as the Intake Air Temperature (IAT) sensor.

DTC No. Proceed to DTC Detection Condition Trouble Area
P0115 Step 1 Open or short in engine coolant temperature sensor circuit for 0.5 seconds
(1 trip detection logic)
·

Open or short in engine coolant temperature sensor circuit

·

Engine coolant temperature sensor

·

ECM


P0117 Step 4 Short in engine coolant temperature sensor circuit for 0.5 seconds
(1 trip detection logic)
·

Short in engine coolant temperature sensor circuit

·

Engine coolant temperature sensor

·

ECM


P0118 Step2 Open in engine coolant temperature sensor circuit for 0.5 seconds
(1 trip detection logic)
·

Open in engine coolant temperature sensor circuit

·

Engine coolant temperature sensor

·

ECM



HINT:

When DTC P0115, P0117 and/or P0118 is detected, check the engine coolant temperature by entering the following menus on the tester: Powertrain / Engine and ECT / Data List / Coolant Temp.

Temperature Displayed Malfunction
-40°C (-40°F) Open circuit
140°C (284°F) Short circuit


WIRING DIAGRAM

A199002E40
5.208,1.573 5.438,1.75 0.229,0.177 10 false 28 5.167,1.771 5.479,1.979 0.313,0.208 10 false B59 5.219,0.958 5.448,1.135 0.229,0.177 10 false 19 5.51,1.667 5.885,1.865 0.375,0.198 10 false E2 5.5,1.052 5.865,1.229 0.365,0.177 10 false THW 5.167,1.156 5.5,1.354 0.333,0.198 10 false B59 0.594,2.385 0.896,2.583 0.302,0.198 10 false k1 2.427,1.021 2.563,1.219 0.135,0.198 10 false 1 2.438,1.667 2.594,1.844 0.156,0.177 10 false 2 5.969,2.688 6.365,2.833 0.396,0.146 10 false ECM 0.594,2.552 2.906,2.771 2.313,0.219 10 false Engine Coolant Temperature Sensor 6.198,0.708 6.51,0.875 0.313,0.167 10 false 5 V 6.125,0.948 6.313,1.125 0.188,0.177 10 false R 2,1.021 2.365,1.208 0.365,0.188 10 false THW 2.115,1.667 2.396,1.865 0.281,0.198 10 false E2

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>N04C-UH (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click here Engine / Hybrid System>N04C-UH (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).


HINT:
·

If DTCs that are related to different systems are output simultaneously while terminal E2 is used as a ground terminal, terminal E2 may have an open circuit.

·

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (COOLANT TEMPERATURE)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.

OK:

Same value as the actual engine coolant temperature.


Result:
Result Proceed to
-40°C (-40°F) A
140°C (284°F) B
OK (same as actual engine coolant temperature) C


HINT:
·

If there is an open circuit, the intelligent tester indicates -40°C (-40°F).

·

If there is a short circuit, the intelligent tester indicates 140°C (284°F).





A

2.READ VALUE USING INTELLIGENT TESTER (CHECK FOR OPEN IN WIRE HARNESS)

B

4.READ VALUE USING INTELLIGENT TESTER (CHECK FOR SHORT IN WIRE HARNESS)

C

2.READ VALUE USING INTELLIGENT TESTER (CHECK FOR OPEN IN WIRE HARNESS)
a.
A227218E03
0.542,3.667 0.948,3.948 0.406,0.281 1.583,3.875 1.135,4.188 true 1.792,3.885 2.344,4.208 true 0.719,0.604 0.938,0.813 0.219,0.208 10 false *1 2.615,0.292 2.844,0.49 0.229,0.198 10 false *2 2.406,1.156 2.802,1.344 0.396,0.188 10 false THW 0.76,4.135 1.156,4.365 0.396,0.229 10 false THW 2.438,1.542 2.719,1.729 0.281,0.188 10 false E2 2.417,4.135 2.698,4.333 0.281,0.198 10 false E2 1.542,2.896 1.76,3.104 0.219,0.208 10 false *3 0.667,3.729 0.948,3.906 0.281,0.177 10 false k1

Disconnect the engine coolant temperature sensor connector.


b.

Connect terminals 1 and 2 of the engine coolant temperature sensor wire harness side connector.


c.

Connect the intelligent tester to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the tester on.


f.

Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.


g.

Read the value.

Standard:

140°C (284°F)


Text in Illustration
*1 Intake Air Temperature Sensor
*2 ECM
*3 Front view of wire harness connector
(to Engine Coolant Temperature Sensor)


h.

Reconnect the engine coolant temperature sensor connector.


Result:
Proceed to
OK
NG



OK

NG

3.READ VALUE USING INTELLIGENT TESTER (CHECK FOR OPEN IN ECM)
3.READ VALUE USING INTELLIGENT TESTER (CHECK FOR OPEN IN ECM)
a.
A153588E27
0.531,2.677 0.938,2.927 0.406,0.25 0.906,3.417 0.708,4.031 true 0.958,3.5 1.188,4.042 true 0.885,0.552 1.156,0.75 0.271,0.198 10 false *1 0.177,2.26 0.469,2.469 0.292,0.208 10 false *3 0.479,4.073 0.885,4.25 0.406,0.177 10 false THW 2.406,1.188 2.76,1.354 0.354,0.167 10 false THW 2.625,0.271 2.833,0.458 0.208,0.188 10 false *2 2.406,1.531 2.646,1.698 0.24,0.167 10 false E2 1.146,4.063 1.427,4.24 0.281,0.177 10 false E2 0.604,2.719 0.906,2.917 0.302,0.198 10 false B59

Disconnect the engine coolant temperature sensor connector.


b.

Connect terminals THW and E2 of the ECM connector.

HINT:

Before checking, perform a visual and contact pressure check for the ECM connector.



c.

Connect the intelligent tester to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the tester on.


f.

Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.


g.

Read the value.

Standard:

140°C (284°F)


Text in Illustration
*1 Engine Coolant Temperature Sensor
*2 ECM
*3 Component with harness connected
(ECM)


h.

Reconnect the engine coolant temperature sensor connector.


Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - ENGINE COOLANT TEMPERATURE SENSOR)

NG

4.READ VALUE USING INTELLIGENT TESTER (CHECK FOR SHORT IN WIRE HARNESS)
a.
A076591E36
0.729,0.292 0.906,0.479 0.177,0.188 10 false *1 2.698,0.24 2.917,0.427 0.219,0.188 10 false *2 2.448,0.906 2.854,1.104 0.406,0.198 10 false THW 2.448,1.292 2.688,1.49 0.24,0.198 10 false E2

Disconnect the engine coolant temperature sensor connector.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the tester on.


e.

Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.


f.

Read the value.

Standard:

-40°C (-40°F)


Text in Illustration
*1 Engine Coolant Temperature Sensor
*2 ECM


g.

Reconnect the engine coolant temperature sensor connector.


Result:
Proceed to
OK
NG



OK

NG

5.READ VALUE USING INTELLIGENT TESTER (CHECK FOR SHORT IN ECM)
5.READ VALUE USING INTELLIGENT TESTER (CHECK FOR SHORT IN ECM)
a.
A153589E23
0.531,2.99 0.938,3.208 0.406,0.219 0.979,4.042 1.198,4.302 true 0.938,3.948 1.313,3.885 true 0.844,0.542 1.156,0.74 0.313,0.198 10 false *1 2.625,0.24 2.938,0.438 0.313,0.198 10 false *2 2.417,1.177 2.813,1.375 0.396,0.198 10 false THW 2.417,1.531 2.813,1.729 0.396,0.198 10 false E2 0.198,2.333 0.51,2.531 0.313,0.198 10 false *3 1.354,3.802 1.74,4.021 0.385,0.219 10 false THW 1.25,4.323 1.5,4.531 0.25,0.208 10 false E2 0.615,3.01 0.927,3.198 0.313,0.188 10 false B59

Disconnect the ECM connector.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the tester on.


e.

Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.


f.

Read the value.

Standard:

-40°C (-40°F)


Text in Illustration
*1 Engine Coolant Temperature Sensor
*2 ECM
*3 Rear view of wire harness connector
(ECM)


g.

Reconnect the engine coolant temperature sensor connector.


Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - ENGINE COOLANT TEMPERATURE SENSOR)

NG