Home › Engine / Hybrid System › N04C-UH (ENGINE CONTROL) › ECD SYSTEM
RM2850E _51 Engine / Hybrid System _073137 N04C-UH ENGINE CONTROL _0355844 ECD SYSTEM C

N04C-UH ENGINE CONTROL  ECD SYSTEM  P0120  Throttle / Pedal Position Sensor / Switch "A" Circuit  P0122  Throttle / Pedal Position Sensor / Switch "A" Circuit Low Input  P0123  Throttle / Pedal Position Sensor / Switch "A" Circuit High Input  


DESCRIPTION

The throttle position sensor is mounted in the diesel throttle body assembly and detects the throttle valve (intake shutter) opening angle.

When the throttle valve is fully closed, a voltage of approximately 0.7 V is applied to terminal VLU of the ECM. The voltage applied to terminal VLU of the ECM increases in proportion to the opening angle of the throttle valve and becomes approximately 3.5 to 4.0 V when the throttle valve is fully opened. The ECM judges the vehicle driving conditions from these signals input from terminal VLU, and uses them as one of the conditions for deciding the air fuel ratio correction, power increase correction and fuel cut control, etc.

A426998E01
2.521,1.281 2.24,0.458 2.24,0.458 2.104,0.458 true 2.667,1.813 2.875,0.479 2.875,0.479 3,0.479 true 2.51,2.531 1.76,3.083 1.76,3.083 1.604,3.083 true 1.573,0.365 2.115,0.563 0.542,0.198 10 false Magnet 3.083,0.396 3.563,0.594 0.479,0.198 10 false Hall IC 1.063,2.99 1.615,3.188 0.552,0.198 10 false Magnet 1.917,3.073 3.469,3.281 1.552,0.208 10 false Throttle Position Sensor 4.51,3 4.927,3.198 0.417,0.198 10 false ECM 4.542,0.969 4.958,1.167 0.417,0.198 10 false 5 V 3.333,1.042 3.615,1.229 0.281,0.188 10 false VC 3.313,1.688 3.646,1.865 0.333,0.177 10 false VTA 3.344,2.333 3.594,2.521 0.25,0.188 10 false E2 3.74,1.042 4,1.229 0.26,0.188 10 false VC 3.688,1.698 4.021,1.875 0.333,0.177 10 false VLU 3.771,2.333 4.021,2.521 0.25,0.188 10 false E2

DTC No. DTC Detection Condition Trouble Area
P0120 Condition of DTC P0122 or P0123 continues for 1 second (open or short in throttle position sensor circuit).
(1 trip detection logic)
·

Open or short in throttle position sensor circuit

·

Throttle position sensor (built into diesel throttle body assembly)

·

ECM


P0122 Open in throttle position sensor circuit for 1 second.
(1 trip detection logic)
·

Open in throttle position sensor circuit

·

Throttle position sensor (built into diesel throttle body assembly)

·

ECM


P0123 Short in throttle position sensor circuit for 1 second.
(1 trip detection logic)
·

Short in throttle position sensor circuit

·

Throttle position sensor (built into diesel throttle body assembly)

·

ECM



WIRING DIAGRAM

A185057E02
5.125,0.521 5.354,0.698 0.229,0.177 10 false 18 5.063,0.75 5.375,0.938 0.313,0.188 10 false B59 5.104,1.01 5.313,1.188 0.208,0.177 10 false 20 5.063,1.229 5.375,1.438 0.313,0.208 10 false B60 5.104,1.469 5.333,1.656 0.229,0.188 10 false 28 5.063,1.677 5.375,1.865 0.313,0.188 10 false B59 2.167,0.625 2.313,0.813 0.146,0.188 10 false 1 2.177,1.563 2.313,1.75 0.135,0.188 10 false 2 2.177,1.115 2.302,1.292 0.125,0.177 10 false 3 0.573,2.188 2.677,2.573 2.104,0.385 10 false Throttle Position Sensor (built into Diesel Throttle Body Assembly) 0.229,2.198 0.542,2.375 0.313,0.177 10 false B27 6.25,0.51 6.552,0.698 0.302,0.188 10 false 5 V 5.448,0.625 5.729,0.802 0.281,0.177 10 false VC 5.448,1.104 5.802,1.302 0.354,0.198 10 false VLU 5.448,1.563 5.698,1.74 0.25,0.177 10 false E2 1.823,0.74 2.094,0.917 0.271,0.177 10 false VC 1.75,1.219 2.083,1.406 0.333,0.188 10 false VTA 1.854,1.677 2.104,1.865 0.25,0.188 10 false E2 5.958,2.219 6.396,2.438 0.438,0.219 10 false ECM

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>N04C-UH (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click here Engine / Hybrid System>N04C-UH (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).


HINT:
·

If DTCs that are related to different systems are output simultaneously while terminal E2 is used as a ground terminal, terminal E2 may have an open circuit.

·

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.INSPECT ECM (VC VOLTAGE)
a.
A224395E37
0.51,0.198 0.938,0.448 0.427,0.25 0.635,1.542 1,1.021 true 1.573,1.552 0.99,0.958 true 0.094,0.083 0.323,0.292 0.229,0.208 10 false *1 0.604,0.25 0.906,0.427 0.302,0.177 10 false B59 1.521,1.583 2.083,1.792 0.563,0.208 10 false 18 (VC) 0.375,1.573 0.917,1.802 0.542,0.229 10 false 28 (E2)

Turn the ignition switch to ON.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
B59-18 (VC) - B59-28 (E2) Ignition switch ON 4.5 to 5.5 V


Text in Illustration
*1 Component with harness connected
(ECM)


Result:
Proceed to
OK
NG



OK

2.INSPECT ECM (VLU VOLTAGE)

NG

2.INSPECT ECM (VLU VOLTAGE)
a.
A224395E38
0.583,0.198 1,0.438 0.417,0.24 1.177,0.208 1.594,0.448 0.417,0.24 0.854,1.531 1,1.031 true 1.938,1.521 1.729,0.958 true 0.104,0.083 0.375,0.333 0.271,0.25 10 false *1 0.667,0.24 0.969,0.417 0.302,0.177 10 false B59 0.604,1.573 1.146,1.781 0.542,0.208 10 false 28 (E2) 1.688,1.573 2.333,1.771 0.646,0.198 10 false 20 (VLU) 1.271,0.25 1.573,0.427 0.302,0.177 10 false B60

Turn the ignition switch to ON.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Throttle Valve Condition Specified Condition
B60-20 (VLU) - B59-28 (E2) Fully open 0.5 to 1.5 V
B60-20 (VLU) - B59-28 (E2) Fully closed 3.2 to 4.2 V
B60-20 (VLU) - B59-28 (E2) Fully open → Fully closed Voltage changes constantly


Text in Illustration
*1 Component with harness connected
(ECM)


Result:
Proceed to
OK
NG



OK

NG

3.INSPECT DIESEL THROTTLE BODY ASSEMBLY
3.INSPECT DIESEL THROTTLE BODY ASSEMBLY
a.
A153602E10
0.365,0.24 0.615,0.469 0.25,0.229 10 false *1

Disconnect the throttle position sensor connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Throttle Valve Condition Specified Condition
2 - 3 Fully closed 0.2 to 5.7 kΩ
Fully open 2.0 to 10.2 kΩ


Text in Illustration
*1 Component with harness connected
(Throttle Position Sensor)


c.

Reconnect the throttle position sensor connector.


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (ECM - THROTTLE POSITION SENSOR)

NG

4.CHECK HARNESS AND CONNECTOR (ECM - THROTTLE POSITION SENSOR)
a.

Disconnect the ECM connectors.


b.

Disconnect the throttle position sensor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
B27-1 (VC) - B59-18 (VC) Always Below 1 Ω
B27-3 (VTA) - B60-20 (VLU) Always Below 1 Ω
B27-2 (E2) - B59-28 (E2) Always Below 1 Ω
B27-1 (VC) or B59-18 (VC) - Body ground Always 10 kΩ or higher
B27-3 (VTA) or B60-20 (VLU) - Body ground Always 10 kΩ or higher



d.

Reconnect the throttle position sensor connector.


e.

Reconnect the ECM connectors.


Result:
Proceed to
OK
NG



OK

5.CHECK DTC OUTPUT

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK DTC OUTPUT
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / DTC.


e.

Read the DTCs.


Result:
Result Proceed to
P0120, P0122 and/or P0123 A
No output B



A

B