Home › Engine / Hybrid System › N04C-UH (ENGINE CONTROL) › ECD SYSTEM
RM2850E _51 Engine / Hybrid System _073137 N04C-UH ENGINE CONTROL _0355844 ECD SYSTEM C

N04C-UH ENGINE CONTROL  ECD SYSTEM  P0180  Fuel Temperature Sensor "A" Circuit  P0182  Fuel Temperature Sensor "A" Circuit Low Input  P0183  Fuel Temperature Sensor "A" Circuit High Input  


DESCRIPTION

The fuel temperature sensor senses the fuel temperature. A thermistor built into the sensor changes its resistance value according to the fuel temperature. The lower the fuel temperature is, the greater the thermistor resistance becomes, and the higher the fuel temperature is, the lower the thermistor resistance becomes (see Fig. 1).

The fuel temperature sensor is connected to the ECM. The 5 V power source voltage in the ECM is applied to the fuel temperature sensor from terminal THF via resistor R. The resistor R and the fuel temperature sensor are connected in series. When the resistance value of the fuel temperature sensor changes in accordance with the fuel temperature, the voltage at terminal THF also changes. Based on this signal, the ECM corrects the pressure control compensation of the injection or supply pump assembly and an error.

A426790E01
1.667,2.042 1.917,1.521 1.917,1.521 2.073,1.521 true 1.417,0.198 2.115,0.417 0.698,0.219 10 false (Figure 1) 0.104,0.417 1.135,0.625 1.031,0.208 10 false Resistance kΩ 2.115,1.427 2.917,1.635 0.802,0.208 10 false Acceptable 1.354,4.198 2.771,4.406 1.417,0.208 10 false Temperature °C (°F) 0.552,0.771 0.76,0.958 0.208,0.188 10 false 30 0.552,0.938 0.76,1.125 0.208,0.188 10 false 20 0.542,1.24 0.75,1.427 0.208,0.188 10 false 10 0.615,1.552 0.76,1.74 0.146,0.188 10 false 5 0.615,1.792 0.76,1.979 0.146,0.188 10 false 3 0.615,1.969 0.76,2.156 0.146,0.188 10 false 2 0.615,2.26 0.76,2.448 0.146,0.188 10 false 1 0.5,3.292 0.76,3.49 0.26,0.198 10 false 0.1 0.5,2.969 0.76,3.167 0.26,0.198 10 false 0.2 0.5,2.792 0.76,2.99 0.26,0.198 10 false 0.3 0.5,2.563 0.76,2.76 0.26,0.198 10 false 0.5 0.854,3.656 1.115,3.854 0.26,0.198 10 false -20 1.219,3.656 1.406,3.833 0.188,0.177 10 false 0 1.531,3.667 1.719,3.844 0.188,0.177 10 false 20 1.823,3.667 2.01,3.844 0.188,0.177 10 false 40 2.135,3.667 2.323,3.844 0.188,0.177 10 false 60 2.49,3.667 2.677,3.844 0.188,0.177 10 false 80 2.802,3.667 3.083,3.854 0.281,0.188 10 false 100 0.854,3.813 1.146,4.01 0.292,0.198 10 false (-4) 1.156,3.813 1.448,4.01 0.292,0.198 10 false (32) 1.479,3.813 1.771,4.01 0.292,0.198 10 false (68) 1.75,3.813 2.146,4 0.396,0.188 10 false (104) 2.073,3.813 2.469,4 0.396,0.188 10 false (140) 2.417,3.813 2.813,4 0.396,0.188 10 false (176) 2.771,3.813 3.167,4 0.396,0.188 10 false (212)

DTC No. DTC Detection Condition Trouble Area
P0180 Open or short in fuel temperature sensor circuit for 0.5 seconds
(1 trip detection logic)
·

Open or short in fuel temperature sensor circuit

·

Fuel temperature sensor (built into injection or supply pump assembly)

·

ECM


P0182 Short in fuel temperature sensor circuit for 0.5 seconds
(1 trip detection logic)
·

Short in fuel temperature sensor circuit

·

Fuel temperature sensor (built into injection or supply pump assembly)

·

ECM


P0183 Open in fuel temperature sensor circuit for 0.5 seconds
(1 trip detection logic)
·

Open in fuel temperature sensor circuit

·

Fuel temperature sensor (built into injection or supply pump assembly)

·

ECM



HINT:

When DTC P0180, P0182 or P0183 is detected, check the fuel temperature by entering the following menus on the intelligent tester: Powertrain / Engine and ECT / Data List / Fuel Temperature.

Temperature Displayed Malfunction
-40°C (-40°F) Open circuit
140°C (284°F) or more Short circuit


WIRING DIAGRAM

A199002E41
5.208,1.573 5.438,1.75 0.229,0.177 10 false 28 5.167,1.771 5.479,1.979 0.313,0.208 10 false B59 5.219,0.958 5.448,1.135 0.229,0.177 10 false 29 5.51,1.667 5.885,1.865 0.375,0.198 10 false E2 5.5,1.052 5.865,1.229 0.365,0.177 10 false THF 5.167,1.156 5.5,1.354 0.333,0.198 10 false B59 0.594,2.385 0.896,2.583 0.302,0.198 10 false B8 2.427,1.021 2.563,1.219 0.135,0.198 10 false 2 2.438,1.667 2.594,1.844 0.156,0.177 10 false 1 5.969,2.688 6.365,2.833 0.396,0.146 10 false ECM 0.594,2.552 3.333,2.938 2.74,0.385 10 false Fuel Temperature Sensor (Built into Injection or Supply Pump Assembly) 6.198,0.708 6.51,0.875 0.313,0.167 10 false 5 V 6.125,0.948 6.313,1.125 0.188,0.177 10 false R 2,1.021 2.365,1.208 0.365,0.188 10 false THF 2.115,1.667 2.396,1.865 0.281,0.198 10 false E2

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>N04C-UH (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click here Engine / Hybrid System>N04C-UH (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).


HINT:
·

If DTCs that are related to different systems are output simultaneously while terminal E2 is used as a ground terminal, terminal E2 may have an open circuit.

·

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (FUEL TEMPERATURE)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Fuel Temperature.


e.

Read the value.

OK:

Same value as the actual fuel temperature.


Result:
Result Proceed to
-40°C (-40°F) A
140°C (284°F) or more B
OK (same as actual fuel temperature) C


HINT:
·

If there is an open circuit, the intelligent tester indicates -40°C (-40°F).

·

If there is a short circuit, the intelligent tester indicates 140°C (284°F) or more.





A

2.READ VALUE USING INTELLIGENT TESTER (CHECK FOR OPEN IN WIRE HARNESS)

B

4.READ VALUE USING INTELLIGENT TESTER (CHECK FOR SHORT IN WIRE HARNESS)

C

2.READ VALUE USING INTELLIGENT TESTER (CHECK FOR OPEN IN WIRE HARNESS)
a.
A204471E20
0.646,3.365 1.031,3.604 0.385,0.24 0.74,3.396 1.063,3.594 0.323,0.198 10 false B8 0.417,2.698 0.729,2.896 0.313,0.198 10 false *3 2.375,1.49 2.688,1.688 0.313,0.198 10 false E2 2.365,1.031 2.823,1.229 0.458,0.198 10 false THF 0.635,0.292 0.979,0.51 0.344,0.219 11 false *1 2.646,0.26 2.958,0.458 0.313,0.198 10 false *2

Disconnect the fuel temperature sensor connector.


b.

Connect terminals 1 and 2 of the wire harness side connector.


c.

Connect the intelligent tester to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the tester on.


f.

Enter the following menus: Powertrain / Engine and ECT / Data List / Fuel Temperature.


g.

Read the value.

Standard:

140°C (284°F) or more


Text in Illustration
*1 Fuel Temperature Sensor
*2 ECM
*3 Front view of wire harness connector
(to Fuel Temperature Sensor)


h.

Reconnect the fuel temperature sensor connector.


Result:
Proceed to
OK
NG



OK

REPLACE INJECTION OR SUPPLY PUMP ASSEMBLY

NG

3.READ VALUE USING INTELLIGENT TESTER (CHECK FOR OPEN IN ECM)
3.READ VALUE USING INTELLIGENT TESTER (CHECK FOR OPEN IN ECM)
a.
A153588E28
0.531,2.677 0.938,2.927 0.406,0.25 0.906,3.5 0.708,4.031 true 0.958,3.5 1.188,4.042 true 0.885,0.552 1.156,0.75 0.271,0.198 10 false *1 0.229,2.25 0.521,2.458 0.292,0.208 10 false *3 0.479,4.073 0.885,4.25 0.406,0.177 10 false THF 2.406,1.188 2.771,1.365 0.365,0.177 10 false THF 2.625,0.271 2.833,0.458 0.208,0.188 10 false *2 2.406,1.531 2.646,1.698 0.24,0.167 10 false E2 1.146,4.063 1.427,4.24 0.281,0.177 10 false E2 0.604,2.719 0.906,2.917 0.302,0.198 10 false B59

Disconnect the fuel temperature sensor connector.


b.

Connect terminals THF and E2 of the ECM connector.

HINT:

Before checking, do a visual and contact pressure check for the ECM connector.



c.

Connect the intelligent tester to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the tester on.


f.

Enter the following menus: Powertrain / Engine and ECT / Data List / Fuel Temperature.


g.

Read the value.

Standard:

140°C (284°F) or more


Text in Illustration
*1 Fuel Temperature Sensor
*2 ECM
*3 Component with harness connected
(ECM)


h.

Reconnect the fuel temperature sensor connector.


Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - FUEL TEMPERATURE SENSOR)

NG

4.READ VALUE USING INTELLIGENT TESTER (CHECK FOR SHORT IN WIRE HARNESS)
a.
A076591E37
0.729,0.292 0.906,0.479 0.177,0.188 10 false *1 2.698,0.24 2.917,0.427 0.219,0.188 10 false *2 2.448,0.906 2.854,1.104 0.406,0.198 10 false THF 2.448,1.292 2.688,1.49 0.24,0.198 10 false E2

Disconnect the fuel temperature sensor connector.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the tester on.


e.

Enter the following menus: Powertrain / Engine and ECT / Data List / Fuel Temperature.


f.

Read the value.

Standard:

-40°C (-40°F)


Text in Illustration
*1 Fuel Temperature Sensor
*2 ECM


g.

Reconnect the fuel temperature sensor connector.


Result:
Proceed to
OK
NG



OK

REPLACE INJECTION OR SUPPLY PUMP ASSEMBLY

NG

5.READ VALUE USING INTELLIGENT TESTER (CHECK FOR SHORT IN ECM)
5.READ VALUE USING INTELLIGENT TESTER (CHECK FOR SHORT IN ECM)
a.
A153589E25
0.531,2.99 0.938,3.208 0.406,0.219 0.979,4.042 1.25,4.188 true 0.927,4.042 1.135,4.375 true 0.844,0.542 1.156,0.74 0.313,0.198 10 false *1 2.625,0.24 2.938,0.438 0.313,0.198 10 false *2 2.417,1.177 2.813,1.375 0.396,0.198 10 false THF 2.417,1.531 2.813,1.729 0.396,0.198 10 false E2 0.198,2.333 0.51,2.531 0.313,0.198 10 false *3 1.042,4.406 1.427,4.625 0.385,0.219 10 false THF 1.313,4.135 1.563,4.344 0.25,0.208 10 false E2 0.615,3.01 0.927,3.198 0.313,0.188 10 false B59

Disconnect the ECM connector.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the tester on.


e.

Enter the following menus: Powertrain / Engine and ECT / Data List / Fuel Temperature.


f.

Read the value.

Standard:

-40°C (-40°F)


Text in Illustration
*1 Fuel Temperature Sensor
*2 ECM
*3 Rear view of wire harness connector
(to Fuel Temperature Sensor)


g.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - FUEL TEMPERATURE SENSOR)

NG