Home › Engine / Hybrid System › N04C-UH (ENGINE CONTROL) › ECD SYSTEM
RM2850E _51 Engine / Hybrid System _073137 N04C-UH ENGINE CONTROL _0355844 ECD SYSTEM C

N04C-UH ENGINE CONTROL  ECD SYSTEM  P0200  Injector Circuit / Open  


DESCRIPTION

The injector driver assembly has been adopted to drive the injector at high speeds. The injector driver assembly has realized high-speed driving under high fuel pressure conditions through the use of a DC/DC converter that provides a high-voltage, quick-charging system.

The ECM constantly monitors the injector driver assembly and stops the engine if an abnormal condition is detected.

DTC No. DTC Detection Condition Trouble Area
P0200 Open or short in injector driver assembly or injector circuit. After engine is started, there is no injection confirmation signal (IJF) from injector driver assembly to ECM despite ECM sending injection command signal (IJT) to injector driver assembly
(1 trip detection logic)
·

Open or short in injector driver assembly circuit

·

Injector assembly

·

Injector driver assembly

·

ECM



WIRING DIAGRAM

A257509E05
6.385,8.333 6.781,8.521 0.396,0.188 10 false ECM 6.177,0.604 6.406,0.792 0.229,0.188 10 false #1 6.177,1.115 6.406,1.302 0.229,0.188 10 false #2 6.177,1.625 6.438,1.823 0.26,0.198 10 false #3 6.177,2.156 6.396,2.354 0.219,0.198 10 false #4 6.177,2.656 6.521,2.844 0.344,0.188 10 false INJF 5.792,0.604 6.104,0.771 0.313,0.167 10 false B59 5.781,1.104 6.073,1.271 0.292,0.167 10 false B59 5.802,1.625 6.094,1.813 0.292,0.188 10 false B59 5.802,2.135 6.115,2.313 0.313,0.177 10 false B59 5.792,2.646 6.094,2.823 0.302,0.177 10 false B59 5.823,0.375 6.042,0.563 0.219,0.188 10 false 24 5.844,0.896 6.042,1.063 0.198,0.167 10 false 23 5.844,1.417 6.052,1.594 0.208,0.177 10 false 22 5.854,1.906 6.094,2.104 0.24,0.198 10 false 21 5.844,2.438 6.073,2.625 0.229,0.188 10 false 25 0.073,8.354 2.115,8.604 2.042,0.25 10 false Injector Driver Assembly (EDU) 0.802,0.583 1.083,0.75 0.281,0.167 10 false #10 0.802,1.104 1.083,1.292 0.281,0.188 10 false #20 0.802,1.615 1.083,1.792 0.281,0.177 10 false #30 0.802,2.125 1.094,2.323 0.292,0.198 10 false #40 0.75,2.646 1.083,2.813 0.333,0.167 10 false INJF 0.771,3.188 1.104,3.365 0.333,0.177 10 false INJ1 0.646,3.719 1.083,3.906 0.438,0.188 10 false COM1 0.76,4.271 1.104,4.438 0.344,0.167 10 false INJ4 0.75,5.344 1.094,5.531 0.344,0.188 10 false INJ2 0.625,5.865 1.115,6.063 0.49,0.198 10 false COM2 0.75,6.448 1.094,6.625 0.344,0.177 10 false INJ3 0.74,7.563 1.083,7.76 0.344,0.198 10 false GND 1.188,7.573 1.479,7.75 0.292,0.177 10 false B95 1.188,0.594 1.479,0.771 0.292,0.177 10 false B95 1.188,1.104 1.469,1.281 0.281,0.177 10 false B95 1.188,1.625 1.521,1.813 0.333,0.188 10 false B95 1.188,2.135 1.49,2.333 0.302,0.198 10 false B95 1.188,2.646 1.49,2.844 0.302,0.198 10 false B96 1.177,3.198 1.5,3.375 0.323,0.177 10 false B98 1.188,3.729 1.49,3.906 0.302,0.177 10 false B98 1.188,4.281 1.5,4.469 0.313,0.188 10 false B98 1.188,5.375 1.531,5.563 0.344,0.188 10 false B96 1.177,5.896 1.479,6.063 0.302,0.167 10 false B98 1.188,6.448 1.49,6.625 0.302,0.177 10 false B96 1.281,0.375 1.417,0.563 0.135,0.188 10 false 6 1.281,0.885 1.406,1.073 0.125,0.188 10 false 2 1.281,1.406 1.417,1.594 0.135,0.188 10 false 1 1.281,1.927 1.417,2.104 0.135,0.177 10 false 3 1.281,2.427 1.396,2.615 0.115,0.188 10 false 1 1.271,2.99 1.427,3.177 0.156,0.188 10 false 5 1.281,3.5 1.417,3.667 0.135,0.167 10 false 1 1.281,4.063 1.417,4.26 0.135,0.198 10 false 4 1.281,5.135 1.406,5.344 0.125,0.208 10 false 4 1.281,5.667 1.417,5.844 0.135,0.177 10 false 2 1.281,6.24 1.417,6.417 0.135,0.177 10 false 2 1.271,7.344 1.406,7.542 0.135,0.198 10 false 4 3.427,3.615 3.552,3.813 0.125,0.198 10 false 1 4.365,3.625 4.521,3.823 0.156,0.198 10 false 2 3.438,4.688 3.563,4.885 0.125,0.198 10 false 1 4.365,4.688 4.5,4.875 0.135,0.188 10 false 2 3.438,5.781 3.563,5.948 0.125,0.167 10 false 1 4.365,5.781 4.5,5.948 0.135,0.167 10 false 2 3.417,6.854 3.563,7.042 0.146,0.188 10 false 1 4.365,6.854 4.5,7.042 0.135,0.188 10 false 2 3.365,3.875 3.604,4.042 0.24,0.167 10 false i1 3.365,4.042 4.885,4.26 1.521,0.219 10 false No. 1 Injector Assembly 3.365,4.927 3.594,5.104 0.229,0.177 10 false i4 3.365,5.073 4.948,5.26 1.583,0.188 10 false No. 4 Injector Assembly 3.406,6.031 3.573,6.208 0.167,0.177 10 false i2 3.406,6.188 4.948,6.385 1.542,0.198 10 false No. 2 Injector Assembly 3.406,7.135 3.583,7.313 0.177,0.177 10 false i3 3.406,7.292 4.979,7.521 1.573,0.229 10 false No. 3 Injector Assembly 4.365,8.135 5.146,8.354 0.781,0.219 10 false *: Shielded 3,7.26 3.156,7.427 0.156,0.167 10 false * 3.302,8.177 3.542,8.375 0.24,0.198 10 false A 3.01,6.167 3.167,6.333 0.156,0.167 10 false * 3.021,5.073 3.177,5.24 0.156,0.167 10 false * 3.01,4 3.167,4.167 0.156,0.167 10 false *

A398537E05
0.802,0.948 1.073,1.115 0.271,0.167 10 false +B 1.198,0.948 1.5,1.125 0.302,0.177 10 false B98 0.094,2.406 1.667,2.615 1.573,0.208 10 false Injector Driver Assembly 0.438,3.677 1.281,3.865 0.844,0.188 10 false R/B NO. 2-B 1.51,3.677 1.792,3.865 0.281,0.188 10 false P/I 0.448,4.031 1.052,4.26 0.604,0.229 10 false FL MAIN 2.802,3.677 3.438,3.875 0.635,0.198 10 false EFI-MAIN 2.667,2.594 3.052,2.792 0.385,0.198 10 false EDU 3.771,2.354 4.156,2.552 0.385,0.198 10 false EDU 2.948,0.313 3.125,0.49 0.177,0.177 10 false A 2.583,0.625 2.76,0.802 0.177,0.177 10 false * 4.656,1.635 4.948,1.823 0.292,0.188 10 false 2C 4.656,2.094 4.948,2.281 0.292,0.188 10 false 2C 4.646,2.802 4.938,2.99 0.292,0.188 10 false 2C 4.646,3.521 4.938,3.708 0.292,0.188 10 false 2D 4.656,3.979 4.948,4.167 0.292,0.188 10 false 2D 2.135,3.521 2.427,3.708 0.292,0.188 10 false 2E 2.135,3.979 2.396,4.156 0.26,0.177 10 false 2D 5.729,2.094 6.031,2.271 0.302,0.177 10 false A54 5.729,3.969 6.031,4.146 0.302,0.177 10 false A54 5.729,4.698 6.031,4.875 0.302,0.177 10 false B60 3.771,4.208 4.156,4.406 0.385,0.198 10 false EFI 3.344,5.052 4.177,5.25 0.833,0.198 10 false *: Shielded 6.406,5.135 6.792,5.333 0.385,0.198 10 false ECM 1.281,0.75 1.406,0.938 0.125,0.188 10 false 6 2.177,3.302 2.302,3.49 0.125,0.188 10 false 1 2.177,3.781 2.302,3.969 0.125,0.188 10 false 3 4.698,1.427 4.823,1.615 0.125,0.188 10 false 4 4.698,1.885 4.823,2.073 0.125,0.188 10 false 3 4.688,2.594 4.813,2.781 0.125,0.188 10 false 2 4.688,3.302 4.813,3.49 0.125,0.188 10 false 4 4.698,3.771 4.823,3.958 0.125,0.188 10 false 2 5.354,3.125 6.031,3.313 0.677,0.188 10 false EFI NO. 2 5.771,1.896 6,2.073 0.229,0.177 10 false 14 6.156,2.083 6.542,2.281 0.385,0.198 10 false IREL 6.156,3.969 6.604,4.156 0.448,0.188 10 false MREL 5.771,3.792 6,3.969 0.229,0.177 10 false 13 5.813,4.49 5.969,4.677 0.156,0.188 10 false 7 6.167,4.677 6.448,4.854 0.281,0.177 10 false E1 1.083,4.844 1.615,5.042 0.531,0.198 10 false Battery 2.771,4.552 6.292,4.75 3.521,0.198 10 false No. 2 Integration Relay

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of this circuits related to this system before performing the following procedure.

·

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>N04C-UH (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click here Engine / Hybrid System>N04C-UH (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).

·

After replacing the injector assembly, the ECM needs registration (Click here Engine / Hybrid System>N04C-UH (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION).



HINT:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK OTHER DTC OUTPUT (IN ADDITION TO DTC P0200)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / DTC.


e.

Read the DTCs.


Result:
Result Proceed to
P0200 A
P0200 and other DTCs B



A

2.INSPECT INJECTOR DRIVER ASSEMBLY (+B VOLTAGE)

B

2.INSPECT INJECTOR DRIVER ASSEMBLY (+B VOLTAGE)
a.
A256736E03
1.479,0.479 1.917,0.75 0.438,0.271 1.479,2.365 1.917,2.635 0.438,0.271 1.969,1.573 2.406,1.865 true 1.052,3.771 1.458,3.51 true 1.563,0.531 1.875,0.719 0.313,0.188 10 false B98 0.146,0.156 0.313,0.313 0.167,0.156 10 false *a 1.563,2.427 1.885,2.604 0.323,0.177 10 false B95 2.479,1.813 2.781,2.031 0.302,0.219 10 false +B 0.677,3.719 1.063,3.927 0.385,0.208 10 false GND

Disconnect the injector driver assembly connectors.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
B98-6 (+B) - B95-4 (GND) Ignition switch ON 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Injector Driver Assembly)


Result:
Proceed to
OK
NG



OK

3.INSPECT INJECTOR DRIVER ASSEMBLY (INJECTOR RESISTANCE)

NG

3.INSPECT INJECTOR DRIVER ASSEMBLY (INJECTOR RESISTANCE)
a.
A187353E03
0.448,1.198 0.844,1.469 0.396,0.271 0.469,3.406 0.865,3.677 0.396,0.271 1.948,1.635 2.375,2.01 true 1.948,1.375 2.375,1 true 1.469,3.719 1.042,4.083 true 1.76,3.719 2.188,4.083 true 1.448,3.427 0.948,2.948 true 1.74,3.396 2.135,2.958 true 0.302,0.24 0.49,0.427 0.188,0.188 10 false *a 0.552,3.458 0.854,3.646 0.302,0.188 10 false B98 0.521,1.25 0.844,1.427 0.323,0.177 10 false B96 2.417,1.948 2.781,2.156 0.365,0.208 10 false INJ2 2.427,0.896 2.802,1.094 0.375,0.198 10 false INJ3 0.688,4.01 1.042,4.208 0.354,0.198 10 false INJ4 2.219,4 2.573,4.188 0.354,0.188 10 false INJ1 0.5,2.844 0.958,3.031 0.458,0.188 10 false COM1 2.177,2.813 2.698,3.042 0.521,0.229 10 false COM2

Disconnect the injector driver assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B98-5 (INJ1) - B98-1 (COM1) 20°C (68°F) 0.85 to 1.05 Ω
B96-4 (INJ2) - B98-2 (COM2) 20°C (68°F) 0.85 to 1.05 Ω
B96-2 (INJ3) - B98-2 (COM2) 20°C (68°F) 0.85 to 1.05 Ω
B98-4 (INJ4) - B98-1 (COM1) 20°C (68°F) 0.85 to 1.05 Ω


Text in Illustration
*a Front view of wire harness connector
(to Injector Driver Assembly)


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (INJECTOR DRIVER ASSEMBLY - ECM)

NG

6.INSPECT INJECTOR ASSEMBLY
4.CHECK HARNESS AND CONNECTOR (INJECTOR DRIVER ASSEMBLY - ECM)
a.

Disconnect the injector driver assembly connectors.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B95-6 (#10) - B59-24 (#1) Always Below 1 Ω
B95-2 (#20) - B59-23 (#2) Always Below 1 Ω
B95-1 (#30) - B59-22 (#3) Always Below 1 Ω
B95-3 (#40) - B59-21 (#4) Always Below 1 Ω
B96-1 (INJF) - B59-25 (INJF) Always Below 1 Ω
B95-6 (#10) or B59-24 (#1) - Body ground Always 10 kΩ or higher
B95-2 (#20) or B59-23 (#2) - Body ground Always 10 kΩ or higher
B95-1 (#30) or B59-22 (#3) - Body ground Always 10 kΩ or higher
B95-3 (#40) or B59-21 (#4) - Body ground Always 10 kΩ or higher
B96-1 (INJF) or B59-25 (INJF) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.INSPECT ECM (OUTPUT VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT ECM (OUTPUT VOLTAGE)
a.

While idling the engine, check the waveform of the ECM connectors using an oscilloscope.

A427250E01
0.854,1.125 1.26,1.406 0.406,0.281 1.469,1.125 1.875,1.406 0.406,0.281 0.542,2.823 0.938,1.885 true 0.906,2.635 0.979,1.896 true 1.406,2.802 1.021,1.906 true 1.781,2.615 1.073,1.906 true 2.563,2.604 1.135,1.896 true 3.156,2.583 1.417,1.75 true 0.927,1.188 1.25,1.385 0.323,0.198 10 false B59 1.552,1.177 1.875,1.375 0.323,0.198 10 false B60 0.146,2.854 0.792,3.052 0.646,0.198 10 false 25 (INJF) 0.719,2.667 1.24,2.865 0.521,0.198 10 false 24 (#1) 1.25,2.813 1.771,3.01 0.521,0.198 10 false 22 (#3) 1.729,2.625 2.25,2.823 0.521,0.198 10 false 23 (#2) 2.406,2.635 2.927,2.833 0.521,0.198 10 false 21 (#4) 3.01,2.625 3.531,2.823 0.521,0.198 10 false 7 (E1) 5.958,0.063 6.615,0.26 0.656,0.198 10 false 5 V/DIV. 6.198,0.51 6.573,0.688 0.375,0.177 10 false GND 6.198,0.833 6.573,1.01 0.375,0.177 10 false GND 6.198,1.146 6.573,1.323 0.375,0.177 10 false GND 6.198,1.458 6.573,1.635 0.375,0.177 10 false GND 4.156,0.521 4.396,0.698 0.24,0.177 10 false #1 4.156,0.823 4.396,1 0.24,0.177 10 false #3 4.156,1.146 4.396,1.323 0.24,0.177 10 false #4 4.156,1.458 4.396,1.635 0.24,0.177 10 false #2 4.792,1.729 5.823,1.927 1.031,0.198 10 false 20 msec./DIV. 0.271,0.292 0.594,0.49 0.323,0.198 10 false *a 5.99,1.927 6.646,2.125 0.656,0.198 10 false 2 V/DIV. 6.198,2.698 6.573,2.875 0.375,0.177 10 false GND 4.823,3.438 5.854,3.635 1.031,0.198 10 false 20 msec./DIV. 4.063,2.542 4.406,2.729 0.344,0.188 10 false INJF

Text in Illustration
*a Component with harness connected
(ECM)
- -

OK:
Tester Connection Condition Specified Condition
B59-24 (#1) - B60-7 (E1) Idling Correct waveform appears as shown
B59-23 (#2) - B60-7 (E1) Idling Correct waveform appears as shown
B59-22 (#3) - B60-7 (E1) Idling Correct waveform appears as shown
B59-21 (#4) - B60-7 (E1) Idling Correct waveform appears as shown
B59-25 (INJF) - B60-7 (E1) Idling Correct waveform appears as shown



Result:
Result Proceed to
#1 to #4 is normal
INJF is abnormal
A
#1 to #4 is abnormal
INJF is normal
B



A

REPLACE INJECTOR DRIVER ASSEMBLY

B

6.INSPECT INJECTOR ASSEMBLY
a.
A081503E33
0.135,0.104 0.354,0.292 0.219,0.188 10 false *a

Disconnect the injector assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 0.85 to 1.05 Ω


Text in Illustration
*a Component without harness connected
(Injector Assembly)


Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (INJECTOR DRIVER ASSEMBLY - INJECTOR ASSEMBLY)

NG