Home › Engine / Hybrid System › N04C-UH (ENGINE CONTROL) › ECD SYSTEM
RM2850E _51 Engine / Hybrid System _073137 N04C-UH ENGINE CONTROL _0355844 ECD SYSTEM C

N04C-UH ENGINE CONTROL  ECD SYSTEM  P0335  Crankshaft Position Sensor "A" Circuit  P0339  Crankshaft Position Sensor "A" Circuit Intermittent  


DESCRIPTION

The crankshaft position sensor (NE signal) consists of a magnet, iron core and pickup coil.

The crankshaft angle sensor plate has 32 teeth and is installed on the injection pump drive gear. The NE signal sensor generates 32 signals of every engine revolution. The ECM detects the standard crankshaft angle based on the G signal from the camshaft position sensor, and the actual crankshaft angle and the engine speed by the NE signal.

DTC No. DTC Detection Condition Trouble Area
P0335 No crankshaft position sensor signal to ECM while cranking for 4.7 seconds or more
No crankshaft position sensor signal to ECM with engine speed 600 rpm or more
(1 trip detection logic)
·

Open or short in crankshaft position sensor circuit

·

Crankshaft position sensor

·

Crankshaft angle sensor plate

·

ECM


P0339 In conditions (a), (b) and (c), no crankshaft position sensor (NE) signal is input for 0.05 seconds or more.
(1 trip detection logic)
(a) Engine revolution is 1000 rpm or more
(b) NE signal is OFF
(c) 3 seconds or more has lapsed after STA signal is switched from ON to OFF
·

Open or short in crankshaft position sensor circuit

·

Crankshaft position sensor

·

Crankshaft angle sensor plate

·

ECM



WIRING DIAGRAM

A129261E05
1.729,0.333 1.844,0.49 0.115,0.156 10 false 1 1.729,0.833 1.844,0.979 0.115,0.146 10 false 2 0.365,1.177 0.646,1.365 0.281,0.188 10 false B5 0.365,1.344 2.115,1.542 1.75,0.198 10 false Crankshaft Position Sensor 2.854,2.354 2.979,2.531 0.125,0.177 10 false 3 4.01,2.104 4.156,2.281 0.146,0.177 10 false 1 4.01,2.615 4.156,2.802 0.146,0.188 10 false 2 3.052,2.479 3.344,2.656 0.292,0.177 10 false VG 3.698,2.208 3.938,2.396 0.24,0.188 10 false G1 3.719,2.708 3.948,2.885 0.229,0.177 10 false G- 2.656,3.073 2.99,3.229 0.333,0.156 10 false k2 2.656,3.229 4.333,3.427 1.677,0.198 10 false Camshaft Position Sensor 0.75,3.208 1.583,3.385 0.833,0.177 10 false * : Shielded 4.604,1.354 4.781,1.531 0.177,0.177 10 false * 6.385,3.354 6.792,3.542 0.406,0.188 10 false ECM 5.823,0.208 6.052,0.406 0.229,0.198 10 false 27 5.76,0.448 6.063,0.656 0.302,0.208 10 false B59 5.823,0.729 6.052,0.906 0.229,0.177 10 false 34 5.76,0.938 6.063,1.125 0.302,0.188 10 false B59 5.823,1.49 6.063,1.688 0.24,0.198 10 false 22 5.771,1.719 6.083,1.906 0.313,0.188 10 false B60 5.813,1.99 6.052,2.177 0.24,0.188 10 false 23 5.76,2.219 6.052,2.427 0.292,0.208 10 false B60 5.792,2.51 6.042,2.719 0.25,0.208 10 false 31 5.76,2.729 6.083,2.938 0.323,0.208 10 false B60 6.156,0.438 6.49,0.625 0.333,0.188 10 false NE+ 6.156,0.938 6.521,1.146 0.365,0.208 10 false NE- 6.156,1.719 6.552,1.927 0.396,0.208 10 false VCG 6.156,2.219 6.427,2.438 0.271,0.219 10 false G+ 6.156,2.719 6.406,2.906 0.25,0.188 10 false G- 1.375,0.438 1.792,0.635 0.417,0.198 10 false NE+ 1.375,0.948 1.792,1.146 0.417,0.198 10 false NE-

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>N04C-UH (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click hereEngine / Hybrid System>N04C-UH (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).


HINT:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK CRANKSHAFT POSITION SENSOR
a.

While idling the engine, check the waveform of the ECM connectors using an oscilloscope.

A427627E02
0.885,0.729 1.281,0.979 0.396,0.25 1.417,0.729 1.813,0.979 0.396,0.25 0.646,1.969 0.854,1.396 true 1.427,2.063 0.854,1.448 true 2.135,2.063 1.698,1.448 true 2.135,0.927 1.698,1.396 true 0.219,0.24 0.531,0.438 0.313,0.198 10 false *1 0.958,0.781 1.271,0.979 0.313,0.198 10 false B59 1.5,0.771 1.813,0.969 0.313,0.198 10 false B60 0.354,2 0.979,2.198 0.625,0.198 10 false 27 (NE+) 1.208,2.094 1.833,2.292 0.625,0.198 10 false 34 (NE-) 2.01,2.104 2.635,2.302 0.625,0.198 10 false 31 (G-) 2.188,0.781 2.813,0.979 0.625,0.198 10 false 23 (G+) 4.083,0.25 4.396,0.448 0.313,0.198 10 false *2 4.125,0.896 4.375,1.083 0.25,0.188 10 false G+ 4.115,1.51 4.365,1.698 0.25,0.188 10 false NE 6.063,0.708 7,0.927 0.938,0.219 10 false 5 V/DIV. 4.802,2.146 6.01,2.385 1.208,0.24 10 false 20 msec./DIV.

Text in Illustration
*1 Component with harness connected
(ECM)
*2 G+ and NE Signal Waveforms

Standard:
Tester Connection Condition Specified Condition
B59-27 (NE+) - B59-34 (NE-) Engine idling Correct waveform appears as shown
B60-23 (G+) - B60-31 (G-) Engine idling Correct waveform appears as shown



Result:
Proceed to
OK
NG



OK

NG

2.INSPECT CRANKSHAFT POSITION SENSOR (RESISTANCE)
2.INSPECT CRANKSHAFT POSITION SENSOR (RESISTANCE)
a.

Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)

NG

3.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)
a.

Disconnect the crankshaft position sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B5-1 (NE+) - B59-27 (NE+) Always Below 1 Ω
B5-2 (NE-) - B59-34 (NE-) Always Below 1 Ω
B5-1 (NE+) or B59-27 (NE+) - Body ground Always 10 kΩ or higher
B5-2 (NE-) or B59-34 (NE-) - Body ground Always 10 kΩ or higher



d.

Reconnect the crankshaft position sensor connector.


e.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

4.CHECK CRANKSHAFT POSITION SENSOR (SENSOR INSTALLATION)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK CRANKSHAFT POSITION SENSOR (SENSOR INSTALLATION)
a.

Check the crankshaft position sensor installation condition.


A369509E04
0.51,1.698 0.813,1.896 0.302,0.198 10 false OK 2.656,1.781 2.948,1.979 0.292,0.198 10 false NG 1.667,1.552 2.344,1.75 0.677,0.198 10 false Clearance

OK:

The crankshaft position sensor is installed properly.


Result:
Proceed to
OK
NG



OK

5.INSPECT CRANKSHAFT POSITION SENSOR PLATE

NG

SECURELY REINSTALL CRANKSHAFT POSITION SENSOR

5.INSPECT CRANKSHAFT POSITION SENSOR PLATE
a.

Check the teeth of the crankshaft angle sensor plate.

OK:

The sensor plate teeth do not have any cracks or deformation.



Result:
Proceed to
OK
NG



OK

NG

REPLACE CRANKSHAFT POSITION SENSOR PLATE