Home › Engine / Hybrid System › N04C-UH (ENGINE CONTROL) › ECD SYSTEM
RM2850E _51 Engine / Hybrid System _073137 N04C-UH ENGINE CONTROL _0355844 ECD SYSTEM C

N04C-UH ENGINE CONTROL  ECD SYSTEM  P0405  Exhaust Gas Recirculation Sensor "A" Circuit Low  P0406  Exhaust Gas Recirculation Sensor "A" Circuit High  


DESCRIPTION

The EGR valve position sensor is mounted on the EGR valve assembly and used for detecting the lift amount of the valve. The lift amount detected by the sensor is provided to the ECM as feedback. The ECM then regulates the lift amount of the valve in accordance with engine running conditions.

DTC No. DTC Detection Condition Trouble Area
P0405 Open in EGR valve position sensor circuit for 5 seconds
(1 trip detection logic)
·

Open in EGR valve position sensor circuit

·

EGR valve assembly

·

ECM


P0406 Short in EGR valve position sensor circuit for 5 seconds
(1 trip detection logic)
·

Short in EGR valve position sensor circuit

·

EGR valve assembly

·

ECM



WIRING DIAGRAM

A403397E03
5.396,1.302 5.74,1.5 0.344,0.198 10 false B59 5.396,1.792 5.74,1.99 0.344,0.198 10 false B60 5.385,2.479 5.729,2.677 0.344,0.198 10 false B59 5.385,3 5.729,3.198 0.344,0.198 10 false B60 5.385,3.583 5.729,3.781 0.344,0.198 10 false A54 4.698,3.583 5.042,3.781 0.344,0.198 10 false 2D 2.896,3.583 3.156,3.792 0.26,0.208 10 false 2D 2.885,5.094 3.146,5.302 0.26,0.208 10 false 2E 4.26,5.25 4.521,5.458 0.26,0.208 10 false 2D 1.5,1.167 1.771,1.365 0.271,0.198 10 false VC 1.344,1.656 1.792,1.865 0.448,0.208 10 false EGLS 1.521,2.354 1.792,2.552 0.271,0.198 10 false E2 1.396,2.979 1.771,3.167 0.375,0.188 10 false EGR 1.5,3.573 1.771,3.771 0.271,0.198 10 false +B 0.323,4.125 0.667,4.313 0.344,0.188 10 false B47 0.333,4.313 2.073,4.521 1.74,0.208 10 false EGR Valve Position Sensor 2.021,3.771 2.885,3.958 0.865,0.188 10 false EFI NO. 3 5.813,1.167 6.083,1.365 0.271,0.198 10 false VC 5.823,1.667 6.271,1.875 0.448,0.208 10 false EGLS 5.823,2.354 6.094,2.552 0.271,0.198 10 false E2 5.802,2.99 6.25,3.198 0.448,0.208 10 false EGRS 5.802,3.583 6.25,3.792 0.448,0.208 10 false MREL 4.635,4.24 4.938,4.427 0.302,0.188 10 false EFI 3.344,5.229 4,5.417 0.656,0.188 10 false EFI-MAIN 2.531,5.531 4.052,5.74 1.521,0.208 10 false No. 2 Integration Relay 5.427,1.083 5.698,1.281 0.271,0.198 10 false 18 6.479,1.083 6.781,1.26 0.302,0.177 10 false 5 V 5.438,1.563 5.708,1.76 0.271,0.198 10 false 33 5.438,2.25 5.708,2.448 0.271,0.198 10 false 28 5.458,2.771 5.688,2.969 0.229,0.198 10 false 3 5.427,3.354 5.698,3.552 0.271,0.198 10 false 13 4.75,3.385 4.906,3.563 0.156,0.177 10 false 5 2.938,3.385 3.094,3.563 0.156,0.177 10 false 4 2.927,4.865 3.156,5.063 0.229,0.198 10 false 2 4.219,5 4.396,5.198 0.177,0.198 10 false 3 5.385,6.385 5.729,6.583 0.344,0.198 10 false B60 5.469,6.156 5.698,6.354 0.229,0.198 10 false 7 5.813,6.375 6.083,6.573 0.271,0.198 10 false E1 6.135,6.99 6.552,7.188 0.417,0.198 10 false ECM 0.896,5.094 1.802,5.313 0.906,0.219 10 false From Battery 1.844,1.167 2.073,1.365 0.229,0.198 10 false 3 1.844,1.667 2.073,1.865 0.229,0.198 10 false 4 1.844,2.354 2.073,2.552 0.229,0.198 10 false 2 1.854,2.875 2.083,3.073 0.229,0.198 10 false 1 1.854,3.469 2,3.656 0.146,0.188 10 false 5

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of this circuits related to this system before performing the following procedure.

·

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>N04C-UH (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click here Engine / Hybrid System>N04C-UH (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).



HINT:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK EGR VALVE ASSEMBLY (POSITION SENSOR POWER SOURCE)
a.
A101429E08
0.24,1.01 0.677,1.26 0.438,0.25 1.479,1.094 1.094,0.74 true 1.75,1.073 2.229,0.688 true 0.104,0.052 0.375,0.26 0.271,0.208 10 false *1 0.323,1.052 0.656,1.25 0.333,0.198 10 false B47 0.885,0.552 1.177,0.75 0.292,0.198 10 false E2 2.313,0.594 2.625,0.781 0.313,0.188 10 false VC

Disconnect the EGR valve assembly connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
B47-3 (VC) - B47-2 (E2) Ignition switch ON 4.5 to 5.5 V


Text in Illustration
*1 Front view of wire harness connector
(to EGR Valve Assembly)


d.

Reconnect the EGR valve assembly connector.


Result:
Proceed to
OK
NG



OK

2.INSPECT EGR VALVE ASSEMBLY (POSITION SENSOR RESISTANCE)

NG

5.CHECK HARNESS AND CONNECTOR (ECM - EGR VALVE ASSEMBLY)
2.INSPECT EGR VALVE ASSEMBLY (POSITION SENSOR RESISTANCE)
a.
A101433E09
0.125,0.094 0.354,0.302 0.229,0.208 10 false *1

Disconnect the EGR valve assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 - 3 20°C (68°F) 2.45 to 4.55 kΩ
2 - 4 20°C (68°F) 2.45 to 4.55 kΩ


Text in Illustration
*1 Component without harness connected
(EGR Valve Assembly)


c.

Reconnect the EGR valve assembly connector.


Result:
Proceed to
OK
NG



OK

3.INSPECT ECM (EGLS VOLTAGE)

NG

3.INSPECT ECM (EGLS VOLTAGE)
a.
A224395E39
0.563,0.198 0.979,0.438 0.417,0.24 1.198,0.188 1.615,0.427 0.417,0.24 0.854,1.531 1,1.031 true 1.479,1.531 1.365,1.021 true 0.104,0.052 0.375,0.302 0.271,0.25 10 false *1 0.635,0.24 0.938,0.417 0.302,0.177 10 false B59 0.604,1.573 1.146,1.781 0.542,0.208 10 false 28 (E2) 1.344,1.563 2.083,1.792 0.74,0.229 10 false 33 (EGLS) 1.292,0.229 1.594,0.406 0.302,0.177 10 false B60

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
B60-33 (EGLS) - B59-28 (E2) Idling 3.0 to 3.5 V
B60-33 (EGLS) - B59-28 (E2) Engine running at 3000 rpm 2.7 to 3.3 V


Text in Illustration
*1 Component with harness connected
(ECM)


Result:
Proceed to
OK
NG



OK

NG

4.CHECK HARNESS AND CONNECTOR (ECM - EGR VALVE ASSEMBLY)
4.CHECK HARNESS AND CONNECTOR (ECM - EGR VALVE ASSEMBLY)
a.

Disconnect the EGR valve assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B60-33 (EGLS) - B47-4 (EGLS) Always Below 1 Ω
B59-28 (E2) - B47-2 (E2) Always Below 1 Ω
B60-33 (EGLS) or B47-4 (EGLS) - Body ground Always 10 kΩ or higher
B59-28 (E2) or B47-2 (E2) - Body ground Always 10 kΩ or higher



d.

Reconnect the EGR valve assembly connector.


e.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (ECM - EGR VALVE ASSEMBLY)
a.

Disconnect the EGR valve assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B59-18 (VC) - B47-3 (VC) Always Below 1 Ω
B59-28 (E2) - B47-2 (E2) Always Below 1 Ω
B59-18 (VC) or B47-3 (VC) - Body ground Always 10 kΩ or higher
B59-28 (E2) or B47-2 (E2) - Body ground Always 10 kΩ or higher



d.

Reconnect the EGR valve assembly connector.


e.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR