Home › Engine / Hybrid System › N04C-UH (ENGINE CONTROL) › ECD SYSTEM
RM2850E _51 Engine / Hybrid System _073137 N04C-UH ENGINE CONTROL _0355844 ECD SYSTEM C

N04C-UH ENGINE CONTROL  ECD SYSTEM  P0500  Vehicle Speed Sensor "A"  


DESCRIPTION

Vehicles, which are equipped with manual transmission, detect the vehicle speed using the vehicle speed sensor. The vehicle speed sensor transmits a 4-pulse signal for every revolution of the rotor shaft, which is rotated by the transmission output shaft via the driven gear. The 4-pulse signal is converted into a more precise rectangular waveform by the waveform shaping circuit inside the combination meter. The signal is then transmitted to the ECM. The ECM determines the vehicle speed based on the frequency of the pulse signal.

A157655E03
1.686,2.13 3.081,2.335 1.395,0.205 10 Vehicle Speed Sensor 3.632,1.896 4.906,2.09 1.274,0.194 10 Combination Meter 5.933,1.918 6.348,2.123 0.414,0.205 10 ECM 2.909,0.695 3.466,0.9 0.557,0.205 10 4-Pulse 4.977,0.695 5.535,0.9 0.557,0.205 10 4-Pulse

DTC No. DTC Detection Condition Trouble Area
P0500 All conditions below are detected continuously for 8 seconds or more:
(2 trip detection logic)
(a) Vehicle speed signal: 0 km/h (0 mph)
(b) Engine speed: 1500 to 2500 rpm
(c) Engine coolant temperature: 70°C (158°F) or more
(d) ECT sensor, accelerator pedal position sensor, and MAF meter are all normal
·

Open or short in vehicle speed sensor circuit

·

Vehicle speed sensor

·

Combination meter

·

ECM



WIRING DIAGRAM

A227221E02
5.604,3.229 6.063,3.448 0.458,0.219 10 false ECM 5.083,1.25 5.458,1.448 0.375,0.198 10 false SPD 4.781,1.208 5.021,1.406 0.24,0.198 10 false 19 4.729,1.406 5.042,1.583 0.313,0.177 10 false A54 4.823,2.302 4.979,2.49 0.156,0.188 10 false 7 4.729,2.5 5.042,2.667 0.313,0.167 10 false B60 5.083,2.5 5.354,2.708 0.271,0.208 10 false E1 1.958,1.302 2.135,1.5 0.177,0.198 10 false 6 1.656,1.417 1.917,1.604 0.26,0.188 10 false +S 1.01,2.198 1.271,2.396 0.26,0.198 10 false J1 0.99,2.365 2.302,2.563 1.313,0.198 10 false Combination Meter 1.479,0.344 2.469,0.542 0.99,0.198 10 false to Tachograph 5.906,0.833 6.25,1.01 0.344,0.177 10 false 5 V

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>N04C-UH (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click here Engine / Hybrid System>N04C-UH (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).


HINT:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK OPERATION OF SPEEDOMETER
a.

Drive the vehicle and check whether the operation of the speedometer in the combination meter is normal.

HINT:
·

The vehicle speed sensor is operating normally if the speedometer reading is normal.

·

If the speedometer does not operate, check it by following the procedure described in speedometer malfunction.



OK:

Speedometer operates normally.



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING INTELLIGENT TESTER (VEHICLE SPEED)

NG

CHECK SPEEDOMETER CIRCUIT (INCLUDE SPEED SENSOR)

2.READ VALUE USING INTELLIGENT TESTER (VEHICLE SPEED)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Vehicle Speed.


e.

Check the vehicle speed at an engine speed of 2000 rpm or more while the vehicle is running.

OK:

Same value as actual vehicle speed.



Result:
Proceed to
OK
NG



OK

NG

3.INSPECT ECM (SPD VOLTAGE)
3.INSPECT ECM (SPD VOLTAGE)
a.
A427655E02
1.26,0.375 1.688,0.646 0.427,0.271 2.531,0.385 2.958,0.656 0.427,0.271 1.073,1.677 1.177,0.958 true 3.073,1.677 2.927,1.135 true 0.135,0.073 0.448,0.271 0.313,0.198 10 false *a 1.344,0.438 1.656,0.635 0.313,0.198 10 false B60 2.615,0.438 2.927,0.635 0.313,0.198 10 false A54 0.906,1.729 1.385,1.938 0.479,0.208 10 false 7 (E1) 2.75,1.719 3.406,1.938 0.656,0.219 10 false 19 (SPD) 0.25,2.563 0.563,2.76 0.313,0.198 10 false 5 V 0.25,3.938 0.563,4.135 0.313,0.198 10 false 0 V

Move the transmission gear selector lever to the neutral position.


b.

Jack up the vehicle.


c.

Turn the ignition switch to ON.


d.

Measure the voltage of the ECM connectors as the wheel is turned slowly.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A59-19 (SPD) - B60-7 (E1) Ignition switch ON Voltage generated intermittently


Text in Illustration
*a Component with harness connected
(ECM)

HINT:

The output voltage should fluctuate up and down similarly to the diagram when the wheel is turned slowly.



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (COMBINATION METER - ECM)