Home › Engine / Hybrid System › N04C-UH (ENGINE CONTROL) › ECD SYSTEM
RM2850E _51 Engine / Hybrid System _073137 N04C-UH ENGINE CONTROL _0355844 ECD SYSTEM C

N04C-UH ENGINE CONTROL  ECD SYSTEM  P0504  Brake Switch "A"/"B" Correlation  


DESCRIPTION

In this system, signals of the stop light switch are used to judge whether the brake system is abnormal or not.

The stop light switch has a duplex system (signals STP and ST1-) to memorize the abnormality when the signals of depressing and releasing the brake pedal are detected simultaneously.

HINT:

Normal condition is as shown in the table below.

Signal Brake Pedal Released In Transition Brake Pedal Depressed
STP OFF ON ON
ST1- ON ON OFF


DTC No. DTC Detection Condition Trouble Area
P0504 Conditions (a) and (b) continue for 0.5 second or more:
(1 trip detection logic)
(a) Ignition switch ON
(b) Open or short in stop light switch signal circuit
·

Short in stop light switch signal circuit

·

Stop light switch

·

ECM



WIRING DIAGRAM

A430901E01
0.354,0.51 2.333,0.885 1.979,0.375 10 false From Instrument Panel Junction Block Terminal (4F-3) 0.344,1.167 2.323,1.542 1.979,0.375 10 false From Instrument Panel Junction Block Terminal (4D-19) 3.031,1.604 3.344,1.802 0.313,0.198 10 false H1 3.031,1.802 4.865,2 1.833,0.198 10 false Stop Light Switch Assembly 4.583,0.677 5.448,0.865 0.865,0.188 10 false STOP NO. 4 6.375,2.365 6.771,2.552 0.396,0.188 10 false ECM 5.76,0.49 6.115,0.677 0.354,0.188 10 false A54 5.771,1.156 6.125,1.344 0.354,0.188 10 false A54 5.771,1.813 6.125,2 0.354,0.188 10 false B60 6.198,0.385 6.552,0.573 0.354,0.188 10 false STP 6.219,1.146 6.604,1.323 0.385,0.177 10 false ST1- 6.219,1.802 6.479,2 0.26,0.198 10 false E1 5.792,0.292 6.052,0.49 0.26,0.198 10 false 18 5.833,0.958 6.094,1.156 0.26,0.198 10 false 8 5.844,1.604 6.104,1.802 0.26,0.198 10 false 7 3.063,0.354 3.25,0.563 0.188,0.208 10 false 1 4.406,0.365 4.594,0.573 0.188,0.208 10 false 2 3.073,1.01 3.26,1.219 0.188,0.208 10 false 3 4.417,1.01 4.604,1.219 0.188,0.208 10 false 4 3.365,0.354 3.552,0.563 0.188,0.208 10 false B 3.375,0.99 3.563,1.198 0.188,0.208 10 false B 4.156,0.354 4.344,0.563 0.188,0.208 10 false L 4.167,0.99 4.354,1.198 0.188,0.208 10 false L

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of this circuits related to this system before performing the following procedure.

·

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>N04C-UH (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click hereEngine / Hybrid System>N04C-UH (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).



HINT:
·

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.

·

STP signal conditions can be checked using the intelligent tester.

(a)

Connect the intelligent tester to the DLC3.

(b)

Turn the ignition switch to ON.

(c)

Turn the tester on.

(d)

Enter the following menus: Powertrain / Engine and ECT / Data List / Stop Light Switch.

(e)

Check the STP signal when the brake pedal is depressed and released.

Result
Brake Pedal Operation Specified Condition
Depressed STP signal ON
Released STP signal OFF




PROCEDURE

1.CHECK STOP LIGHT SWITCH ASSEMBLY (TERMINAL VOLTAGE)
a.
A154599E18
1.542,0.344 1.927,0.594 0.385,0.25 0.656,1.813 1.396,1.76 true 1.469,1.417 0.906,1.083 true 1.635,0.385 1.938,0.583 0.302,0.198 10 false H1 0.156,0.104 0.458,0.292 0.302,0.188 10 false *1 0.51,1.74 0.667,1.938 0.156,0.198 10 false B 0.771,0.969 0.927,1.167 0.156,0.198 10 false B

Disconnect the stop light switch connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
H1-1 (B) - Body ground Always 11 to 14 V
H1-3 (B) - Body ground Ignition switch ON 11 to 14 V


Text in Illustration
*1 Front view of wire harness connector
(to Stop Light Switch)


d.

Reconnect the stop light switch connector.


Result:
Proceed to
OK
NG



OK

2.INSPECT STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

2.INSPECT STOP LIGHT SWITCH ASSEMBLY
a.
C135883E08
0.688,1.208 0.521,1.208 0.521,1.208 0.26,1.958 false 0.24,2.719 0.583,2.917 0.344,0.198 10 false Free 1.031,2.698 1.76,2.906 0.729,0.208 10 false Pushed in 0.75,1.125 1.083,1.313 0.333,0.188 10 false Pin 0.135,0.135 0.406,0.333 0.271,0.198 10 false *1

Remove the stop light switch assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 Switch pin not pushed Below 1 Ω
Switch pin pushed 10 kΩ or higher
3 - 4 Switch pin not pushed 10 kΩ or higher
Switch pin pushed Below 1 Ω


Text in Illustration
*1 Component without harness connected
(Stop Light Switch Assembly)


c.

Reinstall the stop light switch assembly.


Result:
Proceed to
OK
NG



OK

3.INSPECT ECM (STP AND ST1- VOLTAGE)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

3.INSPECT ECM (STP AND ST1- VOLTAGE)
a.
A154601E07
2.479,0.563 2.875,0.781 0.396,0.219 2.927,1.552 3.115,1.823 true 2.927,1.448 2.375,1.823 true 0.125,0.104 0.417,0.333 0.292,0.229 10 false *1 2.833,1.865 3.417,2.063 0.583,0.198 10 false 18 (STP) 1.865,1.854 2.448,2.073 0.583,0.219 10 false 8 (ST1-) 2.563,0.594 2.865,0.771 0.302,0.177 10 false A54

Disconnect the ECM connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A54-8 (ST1-) - Body ground Depressed Below 2 V
Released 11 to 14 V
A54-18 (STP) - Body ground Depressed 11 to 14 V
Released Below 2 V


Text in Illustration
*1 Rear view of wire harness connector
(to ECM)


d.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STOP LIGHT SWITCH - ECM)