Home › Engine / Hybrid System › N04C-UH (ENGINE CONTROL) › ECD SYSTEM
RM2850E _51 Engine / Hybrid System _073137 N04C-UH ENGINE CONTROL _0355844 ECD SYSTEM C

N04C-UH ENGINE CONTROL  ECD SYSTEM  P1426  Differential Pressure Sensor Installation Error  


DESCRIPTION

Refer to DTC P1425 (Click here Engine / Hybrid System>N04C-UH (ENGINE CONTROL)>ECD SYSTEM>P1425).

DTC No. DTC Detection Condition Trouble Area
P1426 When output voltage from the differential pressure sensor indicates positive pressure as negative pressure (and vice versa)
(1 trip detection logic)
·

Incorrect arrangement differential pressure sensor assembly hose piping

·

Differential pressure sensor assembly vacuum hose is clogged

·

Blockage in vacuum transmitting pipe sub-assembly

·

Differential pressure sensor assembly

·

ECM



HINT:
·

DTC P1425 (Differential pressure sensor circuit), DTC P1427 (Differential pressure sensor circuit low) and/or DTC P1428 (Differential pressure sensor high) will be present if there is an open or short in the differential pressure sensor circuit.

·

After confirming DTC P1426, check the differential pressure by entering the following menus on the intelligent tester: Powertrain / Engine and ECT / Data List / DPF Differential Pressure.

Condition Differential Pressure Output Sensor Condition
Ignition Switch ON Approximately 0 kPa Normal
Always -5 or 100 kPa Open or short circuit
3000 rpm (No engine load) Negative output Incorrect arrangement of hose piping



CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>N04C-UH (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click here Engine / Hybrid System>N04C-UH (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).


HINT:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK OTHER DTC OUTPUT (IN ADDITION TO DTC P1426)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / DTC.


e.

Read the DTCs.

Result:
Result Proceed to
P1426 A
P1426 and other DTCs B


HINT:

If codes other than P1426 are output, perform troubleshooting for those DTCs first.




A

2.CHECK CONNECTION OF VACUUM HOSE (DIFFERENTIAL PRESSURE SENSOR ASSEMBLY - CATALYTIC CONVERTER)

B

2.CHECK CONNECTION OF VACUUM HOSE (DIFFERENTIAL PRESSURE SENSOR ASSEMBLY - CATALYTIC CONVERTER)
a.

Check if the vacuum hose routing between the differential pressure sensor assembly and the catalytic converter is correct.


b.

Check that there is no exhaust gas leak between the differential pressure sensor assembly and the catalytic converter.


Result:
Proceed to
OK
NG



OK

3.CHECK BLOCKAGE OF VACUUM HOSE AND CATALYTIC CONVERTER

NG

RECONNECT TO VACUUM HOSE

3.CHECK BLOCKAGE OF VACUUM HOSE AND CATALYTIC CONVERTER
CAUTION:

Be careful of being burned by exhaust gases during the following inspection.


a.

Disconnect the vacuum hose (both upstream and downstream) on the differential pressure sensor assembly.


b.

Start the engine.


c.

Check if there are exhaust gas pulsations from both vacuum hoses during idling.


Result:
Proceed to
OK
NG



OK

4.READ VALUE USING INTELLIGENT TESTER (DIFFERENTIAL PRESSURE)

NG

REPLACE CLOGGED PARTS

4.READ VALUE USING INTELLIGENT TESTER (DIFFERENTIAL PRESSURE)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / DPF Differential Pressure.


d.

Check that differential pressure is within the specification below.

Result
Condition Differential Pressure Output Sensor Condition
Ignition Switch ON Approximately 0 kPa Normal
Always 3 kPa Open or short circuit
3000 rpm (No engine load) Negative output Incorrect arrangement of hose piping


Result:
Proceed to
OK
NG



OK

NG

REPLACE DIFFERENTIAL PRESSURE SENSOR ASSEMBLY