Home › Engine / Hybrid System › N04C-UH (ENGINE CONTROL) › ECD SYSTEM
RM2850E _51 Engine / Hybrid System _073137 N04C-UH ENGINE CONTROL _0355844 ECD SYSTEM C

N04C-UH ENGINE CONTROL  ECD SYSTEM  P1674  Solenoid for Exhaust Brake Circuit Malfunction  


DESCRIPTION

The exhaust brake VSV, mounted on the exhaust retarder, opens and closes according to the signals from the ECM. The ECM receives the signals from the clutch switch and exhaust retarder switch. Through the brake VSV, the ECM controls the negative pressure applied to the diaphragm in the retarder.

DTC No. DTC Detection Condition Trouble Area
P1674 Open or short in exhaust brake solenoid circuit for more than 3 seconds with clutch pedal released
(1 trip detection logic)
·

Open or short in exhaust brake solenoid circuit

·

Exhaust brake with bracket solenoid assembly

·

ECM



WIRING DIAGRAM

A402321E06
0.583,2.396 0.896,2.594 0.313,0.198 10 false A4 0.573,2.573 2.344,2.948 1.771,0.375 10 false Exhaust Brake with Bracket Solenoid Assembly 5.948,2.771 6.26,2.969 0.313,0.198 10 false B60 5.948,2.938 6.333,3.125 0.385,0.188 10 false ECM 5.552,1.188 5.938,1.375 0.385,0.188 10 false EXB 5.563,1.906 5.802,2.094 0.24,0.188 10 false E1 5.313,1.073 5.469,1.271 0.156,0.198 10 false 8 5.313,1.771 5.469,1.969 0.156,0.198 10 false 7 2.063,1.083 2.219,1.281 0.156,0.198 10 false 1 2.063,1.781 2.219,1.979 0.156,0.198 10 false 2

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>N04C-UH (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click here Engine / Hybrid System>N04C-UH (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).


HINT:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.INSPECT ECM (EXB VOLTAGE)
a.
A224395E32
1.188,0.198 1.625,0.448 0.438,0.25 0.76,1.563 1.188,0.781 true 1.99,1.531 1.729,0.875 true 0.083,0.083 0.302,0.292 0.219,0.208 10 false *1 0.563,1.594 1.052,1.802 0.49,0.208 10 false 7 (E1) 1.802,1.594 2.365,1.813 0.563,0.219 10 false 8 (EXB) 1.281,0.24 1.594,0.417 0.313,0.177 10 false B60

Turn the ignition switch to ON.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
B60-8 (EXB) - B60-7 (E1) Exhaust brake is operating 11 to 14 V


Text in Illustration
*1 Component with harness connected
(ECM)


Result:
Proceed to
OK
NG



OK

NG

2.INSPECT EXHAUST BRAKE WITH BRACKET SOLENOID ASSEMBLY
2.INSPECT EXHAUST BRAKE WITH BRACKET SOLENOID ASSEMBLY
a.
A217797E03
0.333,1.396 0.531,1.177 false 0.427,0.563 0.813,0.771 false 3.073,2.188 2.844,2.521 false 2.188,0.552 2.396,0.75 0.208,0.198 10 false *1 0.208,2.625 0.417,2.823 0.208,0.198 10 false *2 0.208,0.417 0.427,0.604 0.219,0.188 10 false *3 0.146,1.365 0.365,1.563 0.219,0.198 10 false *4 3.104,2.063 3.323,2.26 0.219,0.198 10 false *5

Remove the exhaust brake with bracket solenoid assembly.


b.

Check operation of the exhaust brake with bracket solenoid assembly.

OK:
Port Connection Condition Specified Condition
A - B Battery voltage is not applied Air does not flow
B - Air filter Air flows
A - B Battery voltage is applied to terminals 1 and 2 Air flows
B - Air filter Air does not flow


Text in Illustration
*1 Exhaust Brake with Bracket Solenoid Assembly
*2 Component without harness connected
(Exhaust Brake Solenoid)
*3 Port A
*4 Port B
*5 Air Filter


c.

Reinstall the exhaust brake with bracket solenoid assembly.


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (ECM - EXHAUST BRAKE WITH BRACKET SOLENOID ASSEMBLY)

NG

REPLACE EXHAUST BRAKE WITH BRACKET SOLENOID ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (ECM - EXHAUST BRAKE WITH BRACKET SOLENOID ASSEMBLY)
a.

Disconnect the exhaust brake with bracket solenoid assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A4-1 - B60-8 (EXB) Always Below 1 Ω
A4-1 or B60-8 (EXB) - Body ground Always 10 kΩ or higher



d.

Reconnect the exhaust brake with bracket solenoid assembly connector.


e.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR