Home › Engine / Hybrid System › N04C-UH (ENGINE CONTROL) › ECD SYSTEM
RM2850E _51 Engine / Hybrid System _073137 N04C-UH ENGINE CONTROL _0355844 ECD SYSTEM C

N04C-UH ENGINE CONTROL  ECD SYSTEM  P2BAB  NOx Exceedance - Incorrect EGR Flow  


DESCRIPTION

The EGR system recirculates exhaust gases, in order to suit every driving condition. The recirculated gas mingles with intake air, therefore the EGR system can slow combustion speed and keep the combustion temperature down. This helps reduce NOx emission.

In order to increase EGR circulation efficiency, the ECM adjusts the lift amount of the electric EGR controlvalve and throttle valve angle.

DTC No. DTC Detection Condition Trouble Area
P2BAB EGR air flow rate less than the specified value when following conditions (a), (b), (c), (d), (e) and (f) are met:
(2 trip detection logic)
(a) Engine speed is 1400 to 2400 rpm
(b) Injection volume is 25 to 45 mm3/st
(c) Engine running condition is stable
(d) EGR valve assembly opening angle is 5 % or more
(e) Exhaust brake system does not operate
(f) Mass air flow meter sub-assembly circuit malfunction, EGR valve assembly circuit malfunction, manifold absolute pressure sensor circuit malfunction and intake air temperature sensor (after turbocharged) circuit malfunction are not detected
·

EGR valve assembly stuck

·

EGR valve assembly does not move smoothly

·

EGR valve assembly deposit

·

EGR valve assembly passage deposit

·

EGR cooler sub-assembly

·

Air intake system (leaks or blockages)

·

Exhaust gas leaks



MONITOR DESCRIPTION

While driving, if the estimated EGR rate is less than the threshold level for more than a certain period, the ECM determines that the electric EGR control valve is malfunctioning. The ECM then illuminates the MIL.

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>N04C-UH (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click here Engine / Hybrid System>N04C-UH (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).


HINT:
·

When this DTC is stored the vehicle enters fail-safe mode, in which the MIL blinks and the ECM measures elapsed time until an idle signal has been input or engine speed is below 200 rpm after 36 hours, after which engine output is limited to 75%.

·

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P2BAB)
a.

Connect an intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / DTC.


e.

Read the DTCs.

Result:
Result Proceed to
P2BAB A
P2BAB and other DTCs B


HINT:

If any DTCs other than P2BAB are output, troubleshoot those DTCs first.




A

2.CHECK FOR EXHAUST GAS LEAKS

B

2.CHECK FOR EXHAUST GAS LEAKS
a.

Check for exhaust gas leaks.


Result:
Result Proceed to
Exhaust gas leaks out from exhaust system A
No leaks B



A

3.REPAIR EXHAUST GAS LEAK POINT

B

4.CHECK AIR INTAKE SYSTEM (AIR LEAKS AND BLOCKAGES)
3.REPAIR EXHAUST GAS LEAK POINT
a.

Repair or replace the malfunctioning part in exhaust system.


Result:
Proceed to
NEXT



NEXT

4.CHECK AIR INTAKE SYSTEM (AIR LEAKS AND BLOCKAGES)
4.CHECK AIR INTAKE SYSTEM (AIR LEAKS AND BLOCKAGES)
a.

Check for air leaks and blockages in the air intake system.

Result:
Result Proceed to
Leaks or blockages exist in the air intake system A
No leaks and blockages in the air intake system B


HINT:
·

Check for abnormal disconnection, pipe and hose squashing, and any damages in the air intake system.

·

Using your hand, check whether the pipes and hoses in the air intake system are securely connected.

·

Applying soapy water and revving the engine, air leaks from the air intake system can be checked.

·

Check for any modifications in the air intake system made by the user.





A

5.REPAIR OR REPLACE AIR INTAKE SYSTEM

B

6.INSPECT EGR VALVE ASSEMBLY (EGR VALVE OPERATION)
5.REPAIR OR REPLACE AIR INTAKE SYSTEM
a.

Repair or replace the malfunctioning part in the air intake system.


Result:
Proceed to
NEXT



NEXT

6.INSPECT EGR VALVE ASSEMBLY (EGR VALVE OPERATION)
6.INSPECT EGR VALVE ASSEMBLY (EGR VALVE OPERATION)
a.

Remove the EGR valve assembly.


b.

Inspect the EGR valve assembly.

i.

Visually check the EGR valve assembly for deposits.

OK:

No deposits around the EGR valve.



ii.

Visually check that there is no gap between the valve and body.

OK:

No gap between the valve and body.


Result:
Result Proceed to
NG A
OK B




c.

Reinstall the EGR valve assembly.



A

7.REPLACE EGR VALVE ASSEMBLY

B

8.CHECK FOR BLOCKAGE IN EGR GAS PASSAGE (EXHAUST MANIFOLD - EGR COOLER - EGR VALVE ASSEMBLY)
7.REPLACE EGR VALVE ASSEMBLY
a.

Replace the EGR valve assembly (Click here Engine / Hybrid System>N04C-UH (EMISSION CONTROL)>EGR VALVE>REMOVAL).


Result:
Proceed to
NEXT



NEXT

8.CHECK FOR BLOCKAGE IN EGR GAS PASSAGE (EXHAUST MANIFOLD - EGR COOLER - EGR VALVE ASSEMBLY)
8.CHECK FOR BLOCKAGE IN EGR GAS PASSAGE (EXHAUST MANIFOLD - EGR COOLER - EGR VALVE ASSEMBLY)
a.

Check for blockage in the EGR gas passage from the exhaust manifold, through the EGR cooler assembly to the EGR valve assembly.

OK:

No blockage in the EGR gas passage.



Result:
Result Proceed to
NG A
OK B



A

9.REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA

B

10.CHECK WHETHER DTC OUTPUT RECURS
9.REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA
a.

Repair or replace the malfunctioning parts, component and area.


Result:
Proceed to
NEXT



NEXT

10.CHECK WHETHER DTC OUTPUT RECURS
10.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Start the engine and warm it up until the engine coolant temperature reaches 80°C (176°F).


e.

Enter the following menus: Powertrain / Engine and ECT / Data List / Engine Speed, Injection Volume, Engine Load and EGR Lift Sensor Volt %.


f.

Drive the vehicle with the following conditions met for 30 seconds or more.

·

Engine Speed: 1400 to 2400 rpm

·

Injection Volume: 25 to 45 mm3/st

·

Engine Load: Constant

·

EGR Lift Sensor Volt %: 5% or more


HINT:

Refer to the Freeze Frame Data recorded when the DTC was detected.



g.

Enter the following menus: Powertrain / Engine and ECT / DTC.


h.

Read the DTC.


Result:
Result Proceed to
P2BAB A
No output B



A

11.REPLACE EGR COOLER SUB-ASSEMBLY

B

END

11.REPLACE EGR COOLER SUB-ASSEMBLY
a.

Replace the EGR cooler sub-assembly.


Result:
Proceed to
NEXT



NEXT

12.CONFIRM WHETHER DTC OUTPUT RECURS
12.CONFIRM WHETHER DTC OUTPUT RECURS
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Start the engine and warm it up until the engine coolant temperature reaches 80°C (176°F).


e.

Enter the following menus: Powertrain / Engine and ECT / Data List / Engine Speed, Injection Volume, Engine Load and EGR Lift Sensor Volt %.


f.

Drive the vehicle with the following conditions met for 30 seconds or more.

·

Engine Speed: 1400 to 2400 rpm

·

Injection Volume: 25 to 45 mm3/st

·

Engine Load: Constant

·

EGR Lift Sensor Volt %: 5% or more


HINT:

Refer to the Freeze Frame Data recorded when the DTC was detected.



g.

Enter the following menus: Powertrain / Engine and ECT / DTC.


h.

Confirm that the DTC is not output again.

HINT:

If the DTC is output again, the mass air flow meter sub-assembly may be malfunctioning.



Result:
Proceed to
NEXT



NEXT

END