Home › Engine / Hybrid System › N04C-UH (ENGINE CONTROL) › ECD SYSTEM
RM2850E _51 Engine / Hybrid System _073137 N04C-UH ENGINE CONTROL _0355844 ECD SYSTEM C

N04C-UH ENGINE CONTROL  ECD SYSTEM  U1123  Lost Communication with Variable Nozzle Type Turbo Charger Module  


DESCRIPTION

The CAN (Controller Area Network) is a serial data communication system for real time application. It is a multiplex communication system designed for on-vehicle use that provides a superior communication speed of 500 kbps and a capability to detect malfunctions. Through the combination of the CANH and CANL bus lines, the CAN is able to maintain communication based on differential voltage.

HINT:
·

Malfunctions in the CAN bus (communication line) can be checked from the DLC3. (except when the sub bus line of the DLC3 is open.)

·

Diagnostic codes (DTCs) related to CAN communication can be checked by using the intelligent tester.

·

The DLC3 is connected to the CAN communication line, but the CAN communication line cannot detect malfunctions in the DLC3 sub bus line.



DTC No. DTC Detection Condition Trouble Area
U1123 Both of the following conditions are met:
(1 trip detection logic)
(a) Ignition switch ON
(b) No communication between ECM and turbocharger actuator for 0.7 seconds
·

Open or short in turbo actuator circuit

·

Turbocharger sub-assembly

·

CAN bus line

·

ECM



WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses of this circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK WHETHER DTC OUTPUT RECURS (U1123)

b.

Turn the ignition switch off and wait for 1 minute.


c.

Turn the ignition switch to ON.


d.

Turn the tester on.


e.

Enter the following menus: Powertrain / Engine and ECT / DTC.


f.

Read the DTCs.


Result:
Result Proceed to
DTC U1123 A
No output B



A

2.CHECK HARNESS AND CONNECTOR (CAN BUS LINE)

B

2.CHECK HARNESS AND CONNECTOR (CAN BUS LINE)
a.
A164233E25
1.49,0.469 1.844,0.708 0.354,0.24 0.979,1.042 1.427,1.302 true 1.438,1.552 0.938,1.75 true 0.115,0.104 0.396,0.281 0.281,0.177 10 false *1 1.604,0.5 1.906,0.708 0.302,0.208 10 false j4 0.521,0.927 0.979,1.115 0.458,0.188 10 false CANH 0.521,1.688 0.948,1.875 0.427,0.188 10 false CANL

Disconnect the turbocharger connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
j4-1 (CANH) - j4-4 (CANL) Ignition switch OFF 54 to 69 Ω


*1 Front view of wire harness connector
(to Turbocharger Actuator)


c.

Reconnect the turbocharger connector.


Result:
Proceed to
OK
NG



OK

3.CHECK TURBOCHARGER SUB-ASSEMBLY (POWER SOURCE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK TURBOCHARGER SUB-ASSEMBLY (POWER SOURCE)
a.
A164233E26
1.49,0.469 1.844,0.708 0.354,0.24 1.969,1.542 2.417,1.802 true 2.406,1.104 1.969,1.292 true 0.177,0.104 0.458,0.281 0.281,0.177 10 false *1 1.604,0.5 1.906,0.708 0.302,0.208 10 false j4 2.479,1.74 2.865,1.948 0.385,0.208 10 false GND 2.458,1 2.75,1.188 0.292,0.188 10 false +B

Disconnect the turbocharger connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
j4-3 (+B) - j4-6 (GND) Ignition switch ON 11 to 14 V


*1 Front view of wire harness connector
(to Turbocharger Actuator)


d.

Reconnect the turbocharger connector.


Result:
Proceed to
OK
NG



OK

REPLACE TURBOCHARGER SUB-ASSEMBLY

NG

4.CHECK HARNESS AND CONNECTOR (TURBOCHARGER - BODY GROUND)
4.CHECK HARNESS AND CONNECTOR (TURBOCHARGER - BODY GROUND)
a.

Disconnect the turbocharger connector.


b.

Turn the ignition switch to ON.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
j4-6 (GND) - Body ground Always Below 1 Ω



d.

Reconnect the turbocharger connector.


Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (TURBOCHARGER - NO. 2 INTEGRATION RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR