Home › Engine / Hybrid System › N04C-UH (ENGINE CONTROL) › ECD SYSTEM
RM2850E _51 Engine / Hybrid System _073137 N04C-UH ENGINE CONTROL _0355844 ECD SYSTEM C

N04C-UH ENGINE CONTROL  ECD SYSTEM  P0045  Turbocharger / Supercharger Boost Control Solenoid Circuit / Open  


DESCRIPTION

The turbocharger system is comprised of the Variable Nozzle (VN) type turbocharger, the turbo motor driver and ECM.

The turbocharger sub-assembly has a nozzle vane which opens and closes to control the volume of the exhaust gas flowing into the turbine. This, in turn, controls the boost pressure. When the nozzle vane moves towards the closing direction, the pressure increases. When the vane moves towards the opening direction, the pressure decreases.

The turbocharger actuator built on the turbine side activates the nozzle vane. The nozzle vane position sensor built on the actuator detects the opening angle of the nozzle vane. The nozzle vane position sensor signal is sent via the turbo motor driver to the ECM. Then, based on the signal, the ECM actuates the actuator.

The ECM sends a target nozzle vane position signal to the turbo motor driver to obtain the nozzle vane position for the optimal boost pressure in accordance with the driving conditions.

DTC No. DTC Detection Condition Trouble Area
P0045 Send trouble signal in VN turbo controller for 0.3 seconds or more
(1 trip detection logic)
·

Open or short in VN turbo actuator circuit

·

Turbocharger sub-assembly

·

Turbocharger actuator (built into turbocharger sub-assembly)

·

ECM



WIRING DIAGRAM

A398540E02
1.031,2.323 3.01,2.688 1.979,0.365 10 false Turbocharger Actuator (built into Turbocharger Sub-assembly) 2.042,0.417 2.51,0.625 0.469,0.208 10 false CANH 2.073,0.865 2.521,1.073 0.448,0.208 10 false CANL 2.156,1.302 2.521,1.5 0.365,0.198 10 false GND 2.219,1.729 2.5,1.927 0.281,0.198 10 false +B 1.042,2.094 1.51,2.302 0.469,0.208 10 false j4 5.604,0.865 6,1.063 0.396,0.198 10 false A52 5.615,0.427 5.958,0.615 0.344,0.188 10 false A52 6.031,0.427 6.5,0.635 0.469,0.208 10 false CAN+ 6.021,0.875 6.49,1.083 0.469,0.208 10 false CAN- 4.479,2.427 5.177,2.635 0.698,0.208 10 false EFI NO. 3 6.021,3.948 6.49,4.156 0.469,0.208 10 false MREL 2.99,4.74 4.531,5.021 1.542,0.281 10 false No. 2 Integration Relay 1.25,4.833 1.948,5.042 0.698,0.208 10 false Battery 0.604,3.979 1.302,4.188 0.698,0.208 10 false FL MAIN 0.667,3.583 1.573,3.76 0.906,0.177 10 false R/B No. 2-B 1.688,3.583 2.156,3.792 0.469,0.208 10 false P/I 2.51,3.438 2.979,3.646 0.469,0.208 10 false 2E 2.5,3.927 2.969,4.135 0.469,0.208 10 false 2D 4.677,3.938 5.146,4.146 0.469,0.208 10 false 2D 4.677,3.438 5.146,3.646 0.469,0.208 10 false 2D 5.594,3.938 6.063,4.146 0.469,0.208 10 false A54 3.896,4.24 4.365,4.448 0.469,0.208 10 false EFI 6.188,4.979 6.656,5.188 0.469,0.208 10 false ECM 2.542,3.219 2.948,3.458 0.406,0.24 10 false 1 2.542,3.729 2.948,3.969 0.406,0.24 10 false 3 4.719,3.74 5.125,3.979 0.406,0.24 10 false 2 4.719,3.219 4.969,3.406 0.25,0.188 10 false 4 2.583,0.24 2.75,0.427 0.167,0.188 10 false 1 2.583,1.625 2.76,1.813 0.177,0.188 10 false 3 2.583,1.177 2.792,1.375 0.208,0.198 10 false 6 2.583,0.688 2.75,0.865 0.167,0.177 10 false 4 5.646,0.229 5.948,0.417 0.302,0.188 10 false 18 5.646,0.667 5.917,0.865 0.271,0.198 10 false 29 5.635,3.729 5.906,3.938 0.271,0.208 10 false 13 2.927,3.583 3.625,3.792 0.698,0.208 10 false EFI-MAIN

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>N04C-UH (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click here Engine / Hybrid System>N04C-UH (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



HINT:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK TURBOCHARGER SUB-ASSEMBLY (POWER SOURCE)
a.
A164233E27
0.625,1.313 0.969,1.583 0.344,0.271 1.948,1.313 2.375,1.167 true 1.948,1.552 2.344,1.698 true 0.115,0.094 0.375,0.281 0.26,0.188 10 false *1 0.729,1.354 0.958,1.542 0.229,0.188 10 false j4 2.427,1.083 2.708,1.26 0.281,0.177 10 false +B 2.365,1.625 2.729,1.813 0.365,0.188 10 false GND

Disconnect the turbocharger actuator connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
j4-3 (+B) - j4-6 (GND) Ignition switch ON 11 to 14 V


Text in Illustration
*1 Front view of wire harness connector
(to Turbocharger Actuator)


d.

Reconnect the turbocharger actuator connector.


Result:
Proceed to
OK
NG



OK

2.INSPECT TURBOCHARGER SUB-ASSEMBLY

NG

5.CHECK HARNESS AND CONNECTOR (TURBOCHARGER ACTUATOR - BODY GROUND)
2.INSPECT TURBOCHARGER SUB-ASSEMBLY
a.

Inspect the turbocharger sub-assembly (Click hereEngine / Hybrid System>N04C-UH (INTAKE)>INTAKE SYSTEM>ON-VEHICLE INSPECTION).


Result:
Proceed to
OK
NG



OK

3.REPLACE ECM

NG

REPLACE TURBOCHARGER SUB-ASSEMBLY

3.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

4.CHECK WHETHER DTC OUTPUT RECURS
4.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / DTC.


e.

Read the DTCs.


Result:
Result Proceed to
No output A
P0045 B



A

END

B

REPLACE TURBOCHARGER SUB-ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (TURBOCHARGER ACTUATOR - BODY GROUND)
a.

Disconnect the turbocharger actuator connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
j4-6 (GND) - Body ground Always Below 1 Ω



c.

Reconnect the turbocharger actuator connector.


Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (TURBOCHARGER ACTUATOR - NO. 2 INTEGRATION RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR