After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>N04C-UH (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click here Engine / Hybrid System>N04C-UH (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).
If the exhaust temperature sensor detects an abnormally high temperature, conduct the following inspection.
Check the amount of engine oil after troubleshooting is finished.
If the amount of engine oil is more than the specified level, replace the engine oil.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs.
| Result | Proceed to |
|---|---|
| P2002 | A |
| P2002 and other DTCs | B |
A
B
Warm up the engine.
Disconnect the negative battery terminal and wait for at least 1 minute.
Reconnect the negative battery terminal.
Initialize the learning values of the injection or supply pump assembly (Click here Engine / Hybrid System>N04C-UH (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).
Perform initialization with the engine warmed up (engine coolant temperature is 60°C (140°F) or more and fuel temperature is 20°C (68°F) or more).
Initialize the learning values of the diesel throttle body assembly (Click here Engine / Hybrid System>N04C-UH (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).
Connect the intelligent tester to the DLC3.
Start the engine and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Test the Fuel Leak.
Perform the active test.
Visually check the injection or supply pump assembly, injector assembly and fuel line located between the injection or supply pump assembly and common rail assembly for fuel leaks and fuel pressure leaks. Also, perform the same check on the fuel line between the common rail assembly and the injector assembly.
Check that the fuel filter is not clogged.
| Proceed to |
|---|
| NEXT |
NEXT
Check that the intake system pipes and hoses are not excessively contaminated with oil.
If the pipes or hoses are contaminated with oil, clean them.
If pipes or hoses are contaminated with a large amount of oil, repair or replace the parts and areas where the engine oil is leaking from.
Check if the engine oil is leaking from the turbocharger.
| Proceed to |
|---|
| NEXT |
NEXT
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Clear the DTCs (Click here Engine / Hybrid System>N04C-UH (ENGINE CONTROL)>ECD SYSTEM>DTC CHECK / CLEAR).
Perform the forcible regeneration function (Click here Engine / Hybrid System>N04C-UH (ENGINE CONTROL)>ECD SYSTEM>DPF FORCIBLE REGENERATION PROCEDURE).
After the forcible regeneration is completed, allow the engine to idle for at least 5 minutes.
Enter the following menus: Powertrain / Engine and ECT / Data List / DPF Differential Pressure.
Check the differential pressure when the exhaust gas temperature sensor indicates 200°C or less.
If the exhaust gas temperature is high, the differential pressure cannot be measured correctly.
If the differential pressure is outside the normal range, the center exhaust pipe assembly (catalytic converter) may have deteriorated or the center exhaust pipe assembly (catalytic converter) may be clogged with PM.
Fully depress the accelerator pedal and when the engine speed becomes stable, promptly read the differential pressure.
| Engine Speed (no engine load) | Differential Pressure | Proceed to |
|---|---|---|
| 3500 to 3600 rpm (Exhaust gas temperature (up stream) is 200°C or less) | Less than 15 kPa (MIL is not illuminated) | A |
| 15 kPa or more (MIL is not illuminated) | B | |
| MIL remains ON | C |
A
B
C
Click hereEngine / Hybrid System>N04C-UH (ENGINE CONTROL)>ECD SYSTEM>DPF FORCIBLE REGENERATION PROCEDURE