Home › Engine / Hybrid System › N04C-UH (ENGINE CONTROL) › ECD SYSTEM
RM2850E _51 Engine / Hybrid System _073137 N04C-UH ENGINE CONTROL _0355844 ECD SYSTEM J

N04C-UH ENGINE CONTROL  ECD SYSTEM  Abnormal Temperature Detection by Exhaust Temperature Sensor (Downstream)  


CAUTION / NOTICE / HINT

HINT:
·

If the exhaust temperature sensor detects an abnormally high temperature, conduct the following inspection.

·

Check the amount of engine oil after troubleshooting is finished.

·

If the amount of engine oil is more than the specified level, replace the engine oil.



PROCEDURE

1.INSPECT AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY
a.

Inspect the air cleaner filter element sub-assembly.


Result:
Proceed to
OK
NG



OK

2.CHECK INTAKE SYSTEM

NG

REPLACE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

2.CHECK INTAKE SYSTEM
a.

Check for air leaks and blockage between the air cleaner and turbocharger sub-assembly.


b.

Check for air leaks and blockage between the turbocharger sub-assembly and intake manifold.


Result:
Proceed to
OK
NG



OK

3.PERFORM ENGINE RPM ACCELERATION

NG

REPAIR OR REPLACE INTAKE SYSTEM

3.PERFORM ENGINE RPM ACCELERATION
HINT:

If the exhaust gas contains excessive black smoke, perform the following operations:


a.

Warm up the engine.


b.

Disconnect the negative battery terminal and wait for at least 1 minute.


c.

Reconnect the negative battery terminal.


d.

Initialize the learning values of the injection or supply pump assembly (Click here Engine / Hybrid System>N04C-UH (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).

HINT:

Perform initialization with the engine warmed up (engine coolant temperature is 60°C (140°F) or more and fuel temperature is 20°C (68°F) or more).



e.

Initialize the learning values of the diesel throttle body assembly (Click here Engine / Hybrid System>N04C-UH (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION.


f.

Accelerate the engine speed to the maximum rpm with no load 20 times.


g.

Check for black smoke in the exhaust gas.

OK:

Black smoke is not present.


HINT:

Soot deposits in the exhaust system may cause excessive black smoke.



Result:
Proceed to
OK
NG



OK

4.CHECK FUEL SYSTEM

NG

4.CHECK FUEL SYSTEM
a.

Connect the intelligent tester to the DLC3.


b.

Start the engine and turn the tester on.


c.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Test the Fuel Leak.


d.

Perform the active test.


e.

Visually check the injection or supply pump assembly, injector assembly and fuel line located between the injection or supply pump assembly and common rail assembly for fuel leaks and fuel pressure leaks. Also, perform the same check on the fuel line between the common rail assembly and the injector assembly.


f.

Check that the fuel filter is not clogged.


Result:
Proceed to
NEXT



NEXT

5.CHECK FOR ENGINE OIL LEAK
5.CHECK FOR ENGINE OIL LEAK
a.

Check that the intake system pipes and hoses are not excessively contaminated with oil.

HINT:
·

If the pipes or hoses are contaminated with oil, clean them.

·

If pipes or hoses are contaminated with a large amount of oil, repair or replace the parts and areas where the engine oil is leaking from.




b.

Check if the engine oil is leaking from the turbocharger subassembly.


Result:
Proceed to
NEXT



NEXT

6.READ VALUE USING INTELLIGENT TESTER (DIFFERENTIAL PRESSURE)
6.READ VALUE USING INTELLIGENT TESTER (DIFFERENTIAL PRESSURE)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.




f.

After the forcible regeneration is completed, allow the engine to idle for at least 5 minutes.


g.

Enter the following menus: Powertrain / Engine and ECT / Data List / DPF Differential Pressure.


h.

Check the differential pressure when the exhaust gas temperature sensor indicates 200°C or less.

HINT:
·

If the exhaust gas temperature is high, the differential pressure cannot be measured correctly.

·

If the differential pressure is outside the normal range, the monolithic converter assembly may have deteriorated or the monolithic converter assembly may be clogged with PM.

·

Fully depress the accelerator pedal and when the engine speed becomes stable, promptly read the differential pressure.



Result:
Engine Speed (no engine load) Differential Pressure Proceed to
3500 to 3600 rpm (Exhaust gas temperature (up stream) is 200°C or less) Less than 15 kPa (MIL is not illuminated) A
15 kPa or more (MIL is not illuminated) B
MIL remains ON C



i.

Connect the intelligent tester to the DLC3.


j.

Turn the ignition switch to ON.


k.

Turn the tester on.




n.

After the forcible regeneration is completed, allow the engine to idle for at least 5 minutes.


o.

Enter the following menus: Powertrain / Engine and ECT / Data List / DPF Differential Pressure.


p.

Check the differential pressure when the exhaust gas temperature sensor indicates 200°C or less.

HINT:
·

If the exhaust gas temperature is high, the differential pressure cannot be measured correctly.

·

If the differential pressure is outside the normal range, the monolithic converter assembly may have deteriorated or the monolithic converter assembly may be clogged with PM.

·

Fully depress the accelerator pedal and when the engine speed becomes stable, promptly read the differential pressure.



Result:
Engine Speed (no engine load) Differential Pressure Proceed to
3500 to 3600 rpm (Exhaust gas temperature (up stream) is 200°C or less) Less than 15 kPa (MIL is not illuminated) A
15 kPa or more (MIL is not illuminated) B
MIL remains ON C




A

END

B

REPLACE CENTER EXHAUST PIPE ASSEMBLY

C