Home › Engine / Hybrid System › N04C-UH (ENGINE CONTROL) › ECD SYSTEM
RM2850E _51 Engine / Hybrid System _073137 N04C-UH ENGINE CONTROL _0355844 ECD SYSTEM J

N04C-UH ENGINE CONTROL  ECD SYSTEM  Black Smoke Emitted  


CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>N04C-UH (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION and initialization (Click here Engine / Hybrid System>N04C-UH (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).

·

After replacing the injection or supply pump assembly, the ECM needs initialization (Click here Engine / Hybrid System>N04C-UH (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).

·

After replacing the injector assembly, the ECM needs registration (Click here Engine / Hybrid System>N04C-UH (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION).



HINT:

Specified values in the following troubleshooting flowchart are for reference only. Variations in the Data List values may occur depending on the measuring conditions or the vehicle's age. Do not assume the vehicle is normal when the Data List outputs standard values. There may be concealed factors of the malfunction.


PROCEDURE

1.CHECK DTC OUTPUT (RELATED TO ENGINE)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / DTC.


e.

Read the DTCs.


Result:
Result Proceed to
No output A
DTCs related to engine B



A

2.READ VALUE USING INTELLIGENT TESTER (INJECTION VOLUME AND INJECTION FEEDBACK VAL #1 TO #4)

B

2.READ VALUE USING INTELLIGENT TESTER (INJECTION VOLUME AND INJECTION FEEDBACK VAL #1 TO #4)
a.

Connect the intelligent tester to the DLC3.


b.

Start the engine.


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List.


e.

Enter the following menus in order and read the values.

·

Injection Volume

·

Injection Feedback Val #1, #2, #3, and #4


Standard:
Item Engine Speed* Reference Value
Injection Volume Idling (No engine load) 5 to 16 mm3/st
Injection Feedback Val #1 Idling (No engine load) -7.0 to 7.0 mm3/st
Injection Feedback Val #2 Idling (No engine load) -7.0 to 7.0 mm3/st
Injection Feedback Val #3 Idling (No engine load) -7.0 to 7.0 mm3/st
Injection Feedback Val #4 Idling (No engine load) -7.0 to 7.0 mm3/st


HINT:

*: The shift lever should be in the neutral position, and the A/C switch and all accessory switches should be off.



Result:
Proceed to
OK
NG



OK

3.PERFORM ENGINE RPM ACCELERATION

NG

12.INSPECT ECM (THW TERMINAL VOLTAGE)
3.PERFORM ENGINE RPM ACCELERATION
HINT:

If the exhaust gas contains excessive black smoke, perform the following operations:


a.

Accelerate the engine speed to the maximum rpm with no load 20 times.


b.

Check the volume of black smoke in the exhaust gas.

Result:
Result Proceed to
Black smoke is not present A
Black smoke remains in the exhaust gas B


HINT:

Soot deposits in the exhaust system may cause excessive black smoke.




A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

B

4.CHECK AIR INTAKE SYSTEM AND EXHAUST SYSTEM
4.CHECK AIR INTAKE SYSTEM AND EXHAUST SYSTEM

Result:
Proceed to
OK
NG



OK

5.INSPECT EXHAUST RETARDER ASSEMBLY

NG

CHECK AND REPLACE LOCATIONS WHERE MALFUNCTIONS EXIST

5.INSPECT EXHAUST RETARDER ASSEMBLY
a.

Inspect the exhaust retarder assembly.


Result:
Proceed to
OK
NG



OK

6.INSPECT ECM (EGLS VOLTAGE)

NG

REPLACE EXHAUST RETARDER ASSEMBLY

6.INSPECT ECM (EGLS VOLTAGE)
a.
A224395E30
0.563,0.198 0.979,0.438 0.417,0.24 1.198,0.188 1.615,0.427 0.417,0.24 0.854,1.531 1,1.031 true 1.479,1.531 1.365,1.021 true 0.104,0.052 0.375,0.302 0.271,0.25 10 false *a 0.635,0.24 0.938,0.417 0.302,0.177 10 false B59 0.604,1.573 1.146,1.781 0.542,0.208 10 false 28 (E2) 1.344,1.563 2.083,1.792 0.74,0.229 10 false 33 (EGLS) 1.292,0.229 1.594,0.406 0.302,0.177 10 false B60

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
B60-33 (EGLS) - B59-28 (E2) Idling 3.0 to 3.5 V
B60-33 (EGLS) - B59-28 (E2) Engine running at 3000 rpm 2.7 to 3.3 V


Text in Illustration
*a Component with harness connected
(ECM)


Result:
Proceed to
OK
NG



OK

7.INSPECT TURBOCHARGER SUB-ASSEMBLY (PRESSURE)

NG

7.INSPECT TURBOCHARGER SUB-ASSEMBLY (PRESSURE)
a.

Result:
Proceed to
OK
NG



OK

8.READ VALUE USING INTELLIGENT TESTER

NG

REPLACE TURBOCHARGER SUB-ASSEMBLY

8.READ VALUE USING INTELLIGENT TESTER
a.

Connect the intelligent tester to the DLC3.


b.

Start the engine and turn the tester on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List.


d.

Enter the following menus in order and read the values.

·

Fuel Press

·

Injection Volume

·

Main Injection Period

·

Pilot 2 Injection Period

·

Injection Feedback Val #1, #2, #3, and #4


Standard:
Item Engine Speed* Reference Value
Fuel Press Idling 25000 to 35000 kPa
Injection Volume Idling 5 to 16 mm3/st
Main Injection Period Idling 650 to 800 μs
Pilot 2 Injection Period Idling 500 to 600 μs
Injection Feedback Val #1 Idling -7.0 to 7.0 mm3/st
Injection Feedback Val #2 Idling -7.0 to 7.0 mm3/st
Injection Feedback Val #3 Idling -7.0 to 7.0 mm3/st
Injection Feedback Val #4 Idling -7.0 to 7.0 mm3/st


HINT:

*: The shift lever should be in neutral, and the A/C switch and all accessory switches should be OFF.



Result:
Result Proceed to
Within reference value A
One of Injection Feedback Val #1 to #4 is not within reference value B
Other result C



A

9.CHECK CYLINDER COMPRESSION PRESSURE

B

C

12.INSPECT ECM (THW TERMINAL VOLTAGE)
9.CHECK CYLINDER COMPRESSION PRESSURE
a.

Check the cylinder compression pressure (Click here Engine / Hybrid System>N04C-UH (ENGINE MECHANICAL)>ENGINE>ON-VEHICLE INSPECTION).


Result:
Proceed to
OK
NG



OK

10.CHECK HARNESS AND CONNECTOR (INJECTOR ASSEMBLY - INJECTOR DRIVER ASSEMBLY)

NG

CHECK ENGINE TO DETERMINE CAUSE OF LOW COMPRESSION

10.CHECK HARNESS AND CONNECTOR (INJECTOR ASSEMBLY - INJECTOR DRIVER ASSEMBLY)
a.

Check the wire harness and connector.

i.

Disconnect the injector assembly connectors.


ii.

Disconnect the injector driver assembly connectors.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
i1-2 - B98-5 (INJ1) Always Below 1 Ω
i2-2 - B96-4 (INJ2) Always Below 1 Ω
i3-2 - B96-2 (INJ3) Always Below 1 Ω
i4-2 - B98-4 (INJ4) Always Below 1 Ω
i1-1 - B98-1 (COM1) Always Below 1 Ω
i2-1 - B98-2 (COM2) Always Below 1 Ω
i3-1 - B98-2 (COM2) Always Below 1 Ω
i4-1 - B98-1 (COM1) Always Below 1 Ω
i1-2 or B98-5 (INJ1) - Body ground Always 10 kΩ or higher
i2-2 or B96-4 (INJ2) - Body ground Always 10 kΩ or higher
i3-2 or B96-2 (INJ3) - Body ground Always 10 kΩ or higher
i4-2 or B98-4 (INJ4) - Body ground Always 10 kΩ or higher
i1-1 or B98-1 (COM1) - Body ground Always 10 kΩ or higher
i2-1 or B98-2 (COM2) - Body ground Always 10 kΩ or higher
i3-1 or B98-2 (COM2) - Body ground Always 10 kΩ or higher
i4-1 or B98-1 (COM1) - Body ground Always 10 kΩ or higher




Result:
Proceed to
OK
NG



OK

11.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE CYLINDER #1 TO #4 FUEL CUT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE CYLINDER #1 TO #4 FUEL CUT)
HINT:

Use this Active Test to determine the malfunctioning cylinder.


a.

Connect the intelligent tester to the DLC3.


b.

Start the engine.


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Cylinder #1 to #4 Fuel Cut.

HINT:
·

If the engine idle speed does not change when a fuel injector is disabled, the cylinder being tested is malfunctioning.

·

If the cylinder being tested is normal, there will be a significant change in idle speed when the fuel injection is stopped for that cylinder.




Result:
Result Proceed to
Engine idling condition becomes unstable A
Engine idling condition does not change B



A

REPLACE INJECTOR DRIVER ASSEMBLY

B

12.INSPECT ECM (THW TERMINAL VOLTAGE)
a.
A224395E33
0.51,0.198 0.938,0.448 0.427,0.25 0.531,1.531 0.948,0.938 true 1.229,1.542 1,1.031 true 0.094,0.083 0.323,0.292 0.229,0.208 10 false *a 0.604,0.25 0.906,0.427 0.302,0.177 10 false B59 0.229,1.563 0.927,1.771 0.698,0.208 10 false 19 (THW) 1.094,1.573 1.635,1.802 0.542,0.229 10 false 28 (E2)

Start the engine.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
B59-19 (THW) - B59-28 (E2) Idling, engine coolant temperature between 80 to 120°C (176 to 248°F) 0.2 to 1.0 V


Text in Illustration
*a Component with harness connected
(ECM)


Result:
Proceed to
OK
NG



OK

13.INSPECT ECM (PIM TERMINAL VOLTAGE)

NG

19.INSPECT ENGINE COOLANT TEMPERATURE SENSOR
13.INSPECT ECM (PIM TERMINAL VOLTAGE)
a.
A224395E27
0.583,0.198 1,0.438 0.417,0.24 1.177,0.208 1.594,0.448 0.417,0.24 0.854,1.531 1,1.031 true 1.938,1.521 1.74,1.031 true 0.104,0.052 0.375,0.302 0.271,0.25 10 false *a 0.667,0.24 0.969,0.417 0.302,0.177 10 false B59 0.604,1.573 1.146,1.781 0.542,0.208 10 false 28 (E2) 1.688,1.573 2.333,1.771 0.646,0.198 10 false 28 (PIM) 1.271,0.25 1.573,0.427 0.302,0.177 10 false B60

Turn the ignition switch to ON.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
B60-28 (PIM) - B59-28 (E2) Negative pressure of 93 kPa [abs] (697 mmHg, 27.5 in.Hg) applied 0.25 to 0.4 V
Positive pressure of 150 kPa [abs] (1125 mmHg, 44.3 in.Hg) applied 1.0 to 1.4 V


Text in Illustration
*a Component with harness connected
(ECM)


Result:
Proceed to
OK
NG



OK

14.INSPECT CRANKSHAFT POSITION SENSOR

NG

20.CHECK HARNESS AND CONNECTOR (MANIFOLD ABSOLUTE PRESSURE SENSOR - ECM)
14.INSPECT CRANKSHAFT POSITION SENSOR
a.

While idling the engine, check the waveform of the ECM connectors using an oscilloscope.

A427627E05
0.885,0.729 1.281,0.979 0.396,0.25 1.417,0.729 1.813,0.979 0.396,0.25 0.646,1.969 0.854,1.396 true 1.427,2.063 0.854,1.448 true 2.135,2.063 1.698,1.448 true 2.135,0.927 1.698,1.396 true 0.219,0.24 0.531,0.438 0.313,0.198 10 false *1 0.958,0.781 1.271,0.979 0.313,0.198 10 false B59 1.5,0.771 1.813,0.969 0.313,0.198 10 false B60 0.354,2 0.979,2.198 0.625,0.198 10 false 27 (NE+) 1.208,2.094 1.833,2.292 0.625,0.198 10 false 34 (NE-) 2.01,2.104 2.635,2.302 0.625,0.198 10 false 31 (G-) 2.188,0.781 2.813,0.979 0.625,0.198 10 false 23 (G+) 4.083,0.25 4.396,0.448 0.313,0.198 10 false *2 4.125,0.896 4.375,1.083 0.25,0.188 10 false G+ 4.115,1.51 4.365,1.698 0.25,0.188 10 false NE 6.063,0.708 7.156,0.885 1.094,0.177 10 false 5 V/DIV. 4.833,2.135 6.688,2.479 1.854,0.344 10 false 20 msec./DIV.

Text in Illustration
*1 Component with harness connected
(ECM)
*2 G+ and NE Signal Waveforms

OK:
Tester Connection Condition Specified Condition
B59-27 (NE+) - B59-34 (NE-) Engine idling Correct waveform appears as shown
B60-23 (G+) - B60-31 (G-) Engine idling Correct waveform appears as shown



Result:
Proceed to
OK
NG



OK

15.INSPECT ECM (VPA AND VPA2 TERMINAL VOLTAGE)

NG

21.INSPECT CRANKSHAFT POSITION SENSOR
15.INSPECT ECM (VPA AND VPA2 TERMINAL VOLTAGE)
a.
A224395E34
2.542,0.135 2.969,0.385 0.427,0.25 2.271,0.469 2.802,0.948 true 3.042,1.635 2.813,1.031 true 2.438,1.781 2.75,1.031 true 2.01,1.552 2.75,0.958 true 0.094,0.083 0.323,0.292 0.229,0.208 10 false *a 2.625,0.188 2.958,0.375 0.333,0.188 10 false A54 2.75,1.656 3.396,1.854 0.646,0.198 10 false 28 (EPA) 1.677,0.281 2.333,0.5 0.656,0.219 10 false 22 (VPA) 2.052,1.802 2.75,2 0.698,0.198 10 false 29 (EPA2) 1.521,1.573 2.219,1.771 0.698,0.198 10 false 23 (VPA2)

Turn the ignition switch to ON.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Condition Accelerator Pedal Condition Specified Condition
A54-22 (VPA) - A54-28 (EPA) Released 0.6 to 1.0 V
A54-22 (VPA) - A54-28 (EPA) Depressed 2.8 to 3.6 V
A54-23 (VPA2) - A54-29 (EPA2) Released 1.4 to 1.8 V
A54-23 (VPA2) - A54-29 (EPA2) Depressed 3.6 to 4.4 V


Text in Illustration
*a Component with harness connected
(ECM)


Result:
Proceed to
OK
NG



OK

16.INSPECT ECM (THA TERMINAL VOLTAGE)

NG

22.CHECK HARNESS AND CONNECTOR (ACCELERATOR PEDAL POSITION SENSOR - ECM)
16.INSPECT ECM (THA TERMINAL VOLTAGE)
a.
A224395E35
0.51,0.198 0.938,0.448 0.427,0.25 0.573,1.521 0.833,1.031 true 1.229,1.542 1,1.031 true 0.094,0.083 0.323,0.292 0.229,0.208 10 false *a 0.604,0.25 0.906,0.427 0.302,0.177 10 false B59 0.198,1.573 0.833,1.781 0.635,0.208 10 false 31 (THA) 1.094,1.573 1.635,1.802 0.542,0.229 10 false 28 (E2)

Start the engine.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Condition Accelerator Pedal Condition Specified Condition
B59-31 (THA) - B59-28 (E2) Idling, intake air temperature at 0 to 80°C (32 to 176°F) 0.5 to 3.4 V


Text in Illustration
*a Component with harness connected
(ECM)


Result:
Proceed to
OK
NG



OK

17.INSPECT ECM (THIA TERMINAL VOLTAGE)

NG

23.INSPECT MASS AIR FLOW METER SUB-ASSEMBLY (INTAKE AIR TEMPERATURE SENSOR)
17.INSPECT ECM (THIA TERMINAL VOLTAGE)
a.
A224395E36
0.51,0.198 0.938,0.448 0.427,0.25 0.531,1.531 0.896,0.938 true 1.229,1.542 1,1.031 true 0.094,0.083 0.323,0.292 0.229,0.208 10 false *a 0.604,0.25 0.906,0.427 0.302,0.177 10 false B59 0.229,1.563 0.927,1.771 0.698,0.208 10 false 20 (THIA) 1.094,1.573 1.635,1.802 0.542,0.229 10 false 28 (E2)

Start the engine.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Condition Accelerator Pedal Condition Specified Condition
B59-20 (THIA) - B59-28 (E2) Idling, intake air temperature at 0 to 80°C (32 to 176°F) 1.0 to 4.4 V


Text in Illustration
*a Component with harness connected
(ECM)


Result:
Proceed to
OK
NG



OK

18.INSPECT ECM (PCR1 TERMINAL VOLTAGE)

NG

24.INSPECT INTAKE AIR TEMPERATURE SENSOR
18.INSPECT ECM (PCR1 TERMINAL VOLTAGE)
a.
A224395E25
0.51,0.198 0.938,0.448 0.427,0.25 0.323,1.531 0.563,0.958 true 1.229,1.542 1,1.031 true 0.094,0.083 0.323,0.292 0.229,0.208 10 false *a 0.604,0.25 0.906,0.427 0.302,0.177 10 false B59 0.094,1.573 0.833,1.792 0.74,0.219 10 false 26 (PCR1) 1.094,1.573 1.635,1.802 0.542,0.229 10 false 28 (E2)

Start the engine.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Condition Accelerator Pedal Condition Specified Condition
B59-26 (PCR1) - B59-28 (E2) Idling 1.3 to 1.7 V


Text in Illustration
*a Component with harness connected
(ECM)


Result:
Proceed to
OK
NG



OK

NG

25.INSPECT COMMON RAIL ASSEMBLY (FUEL PRESSURE SENSOR)
19.INSPECT ENGINE COOLANT TEMPERATURE SENSOR
a.
A126612E16
0.729,0.245 0.949,0.388 0.22,0.143 10 *1 0.635,1.687 0.811,1.828 0.177,0.142 10 30 0.635,1.877 0.811,2.019 0.177,0.142 10 20 0.635,2.176 0.811,2.318 0.177,0.142 10 10 0.732,2.49 0.83,2.632 0.098,0.142 10 5 0.732,3.145 0.83,3.287 0.098,0.142 10 1 2.419,2.95 2.603,3.121 0.184,0.171 10 *2 1.194,3.375 1.388,3.547 0.193,0.171 10 *a 0.732,2.904 0.83,3.046 0.098,0.142 10 2 0.732,2.709 0.83,2.851 0.098,0.142 10 3 0.587,3.602 0.802,3.743 0.216,0.142 10 0.3 0.587,3.416 0.802,3.558 0.216,0.142 10 0.5 0.587,3.952 0.802,4.094 0.216,0.142 10 0.1 0.587,3.761 0.802,3.903 0.216,0.142 10 0.2 0.89,4.019 1.108,4.165 0.218,0.146 10 -20 1.279,4.019 1.374,4.171 0.095,0.152 10 0 1.542,4.019 1.716,4.165 0.174,0.146 10 20 1.884,4.019 2.058,4.17 0.174,0.151 10 40 2.223,4.019 2.399,4.168 0.176,0.149 10 80 2.594,4.019 2.893,4.161 0.299,0.142 10 100 0.879,4.192 1.115,4.366 0.236,0.174 10 (-4) 1.17,4.192 1.441,4.366 0.271,0.174 10 (32) 1.482,4.192 1.753,4.366 0.271,0.174 10 (68) 1.786,4.192 2.133,4.366 0.347,0.174 10 (104) 2.185,4.192 2.533,4.366 0.347,0.174 10 (176) 2.594,4.192 2.941,4.366 0.347,0.174 10 (212) 0.878,1.575 1.081,1.727 0.203,0.152 10 kΩ 0.304,4.034 0.514,4.196 0.21,0.162 10 °C 0.243,4.233 0.54,4.395 0.296,0.162 10 (°F) 1.574,2.846 1.308,3.198 1.308,3.198 1.308,3.334 false

Remove the engine coolant temperature sensor.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 2.32 to 2.59 kΩ
80°C (176°F) 0.31 to 0.326 kΩ


Text in Illustration
*1 Ohmmeter
*2 Engine Coolant Temperature Sensor
*a Acceptable

NOTICE:

When checking the sensor in water, keep the terminals dry. After the check, wipe the sensor dry.


HINT:

Alternative procedure: Connect an ohmmeter to the installed engine coolant temperature sensor and read the resistance. Use an infrared thermometer to measure the engine temperature in the immediate vicinity of the sensor. Compare these values against the resistance/ temperature graph. Change the engine temperature (warm up or cool down) and repeat the test.



c.

Reinstall the engine coolant temperature sensor.


Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM)

NG

20.CHECK HARNESS AND CONNECTOR (MANIFOLD ABSOLUTE PRESSURE SENSOR - ECM)
a.

Disconnect the manifold absolute pressure sensor connector.


b.

Disconnect the ECM connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B18-2 (PIM) - B60-28 (PIM) Always Below 1 Ω
B18-3 (VC) - B59-18 (VC) Always Below 1 Ω
B18-1 (E) - B59-28 (E2) Always Below 1 Ω
B18-2 (PIM) or B60-28 (PIM) - Body ground Always 10 kΩ or higher
B18-3 (VC) or B59-18 (VC) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

21.INSPECT CRANKSHAFT POSITION SENSOR
a.

Inspect the crankshaft position sensor (Click here Engine / Hybrid System>N04C-UH (ENGINE CONTROL)>CRANKSAFT POSITION SENSOR>REMOVAL).


Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)

NG

22.CHECK HARNESS AND CONNECTOR (ACCELERATOR PEDAL POSITION SENSOR - ECM)
a.

Check the wire harness and connector.

i.

Disconnect the accelerator pedal position sensor connector.


ii.

Disconnect the ECM connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F9-2 (EPA2) - A54-29 (EPA2) Always Below 1 Ω
F9-1 (VPA2) - A54-23 (VPA2) Always Below 1 Ω
F9-4 (VCPA) - A54-20 (VCPA) Always Below 1 Ω
F9-3 (EPA) - A54-28 (EPA) Always Below 1 Ω
F9-5 (VPA) - A54-22 (VPA) Always Below 1 Ω
F9-2 (EPA2) or A54-29 (EPA2) - Body ground Always 10 kΩ or higher
F9-1 (VPA2) or A54-23 (VPA2) - Body ground Always 10 kΩ or higher
F9-4 (VCPA) or A54-20 (VCPA) - Body ground Always 10 kΩ or higher
F9-3 (EPA) or A54-28 (EPA) - Body ground Always 10 kΩ or higher
F9-5 (VPA) or A54-22 (VPA) - Body ground Always 10 kΩ or higher




Result:
Proceed to
OK
NG



OK

REPLACE ACCELERATOR LINK ASSEMBLY (ACCELERATOR PEDAL POSITION SENSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

23.INSPECT MASS AIR FLOW METER SUB-ASSEMBLY (INTAKE AIR TEMPERATURE SENSOR)
a.

Inspect the mass air flow meter sub-assembly (Click here Engine / Hybrid System>N04C-UH (ENGINE CONTROL)>MASS AIR FLOW METER>ON-VEHICLE INSPECTION).


Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (MASS AIR FLOW METER - ECM)

NG

REPLACE MASS AIR FLOW METER SUB-ASSEMBLY

24.INSPECT INTAKE AIR TEMPERATURE SENSOR
a.

Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (INTAKE AIR TEMPERATURE SENSOR - ECM)

NG

25.INSPECT COMMON RAIL ASSEMBLY (FUEL PRESSURE SENSOR)
a.
A160890E13
0.334,0.478 0.558,0.646 0.223,0.168 10 *a

Disconnect the fuel pressure sensor connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 2 20°C (68°F) 16.4 kΩ or less
2 - 1 20°C (68°F) 3 kΩ or less


Text in Illustration
*a Component without harness connected
(Fuel Pressure Sensor)


Result:
Proceed to
OK
NG



OK

26.CHECK HARNESS AND CONNECTOR (FUEL PRESSURE SENSOR - ECM)

NG

REPLACE COMMON RAIL ASSEMBLY

26.CHECK HARNESS AND CONNECTOR (FUEL PRESSURE SENSOR - ECM)
a.

Disconnect the ECM connector.


b.

Disconnect the fuel pressure sensor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B59-26 (PCR1) - B92-2 (PCR1) Always Below 1 Ω
B59-18 (VC) - B92-3 (VC1) Always Below 1 Ω
B59-28 (E2) - B92-1 (E1) Always Below 1 Ω
B59-26 (PCR1) or B92-2 (PCR1) - Body ground Always 10 kΩ or higher
B59-18 (VC) or B92-3 (VC1) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

27.REPLACE ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

27.REPLACE ECM
a.

Replace the ECM

NOTICE:

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>N04C-UH (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click here Engine / Hybrid System>N04C-UH (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).



b.

Check the volume of black smoke in the exhaust gas.

OK:

Black smoke is not present.



Result:
Proceed to
OK
NG



OK

END

NG

REPLACE INJECTION OR SUPPLY PUMP ASSEMBLY