Home › Engine / Hybrid System › N04C-VQ (ENGINE CONTROL) › ECD SYSTEM
RM2850E _51 Engine / Hybrid System _073138 N04C-VQ ENGINE CONTROL _0355854 ECD SYSTEM D

N04C-VQ ENGINE CONTROL  ECD SYSTEM  DIAGNOSIS SYSTEM  


DESCRIPTION


A093827

When troubleshooting Euro-OBD vehicles, the vehicle must be connected to the GTS. Various data output from the vehicle's Engine Control Module (ECM) can then be read.

The Malfunction Indicator Lamp (MIL) is illuminated and blinked when the vehicle's on-board computer detects a malfunction in the computer itself or in drive system components. In addition, the applicable Diagnostic Trouble Codes (DTCs) are recorded in the ECM memory (Click hereEngine / Hybrid System>N04C-VQ (ENGINE CONTROL)>ECD SYSTEM>DIAGNOSTIC TROUBLE CODE CHART).

If the malfunction does not recur, the MIL stays on until the ignition switch is turned off, and then the MIL turns off when the ignition switch is turned to ON. Be aware that the DTCs remain recorded in the ECM memory.

To check the DTCs, connect the GTS to the DLC3 on the vehicle.


NORMAL MODE AND CHECK MODE


The diagnosis system operates in "normal mode" during normal vehicle use. In normal mode, "2 trip detection logic" is used to ensure accurate detection of malfunctions. "Check mode" is also available to technicians as an option. In check mode, "1 trip detection logic" is used for simulating malfunction symptoms and increasing the system's ability to detect malfunctions, including intermittent malfunctions (Click hereEngine / Hybrid System>N04C-VQ (ENGINE CONTROL)>ECD SYSTEM>CHECK MODE PROCEDURE).


2 TRIP DETECTION LOGIC


When a malfunction is first detected, the malfunction is temporarily stored in the ECM memory (1st trip). If the same malfunction is detected during the next subsequent drive cycle, the MIL is illuminated (2nd trip).


FREEZE FRAME DATA


The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was moving or stationary, whether the engine was warmed up or not, as well as other data recorded at the time of a malfunction.


CHECK DLC3 (Data Link Connector 3)


H100769E16
1.054,0.286 1.304,0.433 0.25,0.147 10 CG 1.454,0.297 1.76,0.452 0.306,0.155 10 SG 2.355,1.816 2.687,1.985 0.332,0.169 10 BAT 2.499,0.297 2.727,0.444 0.228,0.147 10 SIL 1.849,0.302 2.284,0.457 0.435,0.155 10 CANH 1.491,1.827 1.927,1.982 0.435,0.155 10 CANL 2.332,1.436 2.52,1.818 false 1.966,1.444 1.699,1.827 false 1.219,0.465 1.606,0.905 false 1.603,0.487 1.781,0.881 false 1.964,0.891 2.11,0.469 false 2.151,0.899 2.616,0.487 false

The ECM uses ISO 15765-4 for communication. The terminal arrangement of the DLC3 complies with ISO 15031-03 and matches the ISO 15765-4 format.

HINT:

Connect the cable of the GTS to the DLC3, turn the ignition switch to ON and attempt to use the GTS. If the display indicates that a communication error has occurred, there is a problem either with the vehicle or with the GTS.

If communication is normal when the GTS is connected to another vehicle, inspect the DLC3 of the original vehicle.

If communication is still not possible when the GTS is connected to another vehicle, the problem may be in the GTS itself. Consult the Service Department listed in the GTS instruction manual.


Symbols (Terminal No.) Terminal Description Condition Result
SIL (7) - SG (5) Bus "+" line During transmission Pulse generation
CG (4) - Body ground Chassis ground Always Below 1 Ω
SG (5) - Body ground Signal ground Always Below 1 Ω
BAT (16) - Body ground Battery positive Always 11 to 14 V
CANH (6) - CANL (14) CAN bus line Ignition switch off* 54 to 69 Ω
CANH (6) - CG (4) HIGH-level CAN bus line Ignition switch off* 200 Ω or higher
CANL (14) - CG (4) LOW-level CAN bus line Ignition switch off* 200 Ω or higher
CANH (6) - BAT (16) HIGH-level CAN bus line Ignition switch off* 6 kΩ or higher
CANL (14) - BAT (16) LOW-level CAN bus line Ignition switch off* 6 kΩ or higher

NOTICE:

*: Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the ignition switch, any other switches or the doors.



INSPECT BATTERY VOLTAGE


If the voltage is below 11 V, recharge or replace the battery.

Battery voltage:

11 to 14 V



CHECK MIL


A093827

a.

The MIL will be illuminated when the ignition switch is turned to ON and the engine is not running.

HINT:

If the MIL is not illuminated, check the MIL circuit (Click hereEngine / Hybrid System>N04C-VQ (ENGINE CONTROL)>ECD SYSTEM>MIL Circuit).



b.

When the engine is started, the MIL should turn off. If the MIL remains on or flashes, the diagnosis system has detected a malfunction or abnormality in the ECD system.



ALL READINESS


HINT:
·

With "All Readiness" you can check whether or not the DTC judgement has been completed by using the GTS.

·

Check "All Readiness" after simulating malfunction symptoms or for validation after finishing repairs.



a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.



e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON and turn the GTS on.


g.

Perform the DTC judgment driving pattern to run the DTC judgement.


h.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.


i.

Input the DTCs to be confirmed.


j.

Check the DTC judgement result.

Result
GTS Display Description
NORMAL
·

DTC judgement completed

·

System normal


ABNORMAL
·

DTC judgement completed

·

System abnormal


INCOMPLETE
·

DTC judgement not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgement

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU's memory limit