The Malfunction Indicator Lamp (MIL) is used to indicate vehicle malfunctions detected by the ECM. By turning the ignition switch to ON, power is supplied to the MIL circuit, and the ECM provides the circuit ground which illuminates the MIL.
The MIL operation can be checked visually. When the ignition switch is first turned to ON, the MIL should illuminate and should then turn off. If the MIL remains illuminated or does not illuminate, conduct the following troubleshooting procedure. If the ECM detects any trouble, the MIL illuminates. At this time, the ECM records a DTC in the memory.
After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>N04C-VQ (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click hereEngine / Hybrid System>N04C-VQ (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
Turn the ignition switch to ON.
Check the illumination of the MIL.
| Result | Proceed to |
|---|---|
| MIL remains illuminated (Even after ignition switch is turned to ON and several seconds have passed, MIL still remains illuminated) | A |
| MIL remains off (Does not illuminate at all) | B |
| MIL illuminates for several seconds, but turns off after engine is started | C |
A
C
Click hereEngine / Hybrid System>N04C-VQ (ENGINE CONTROL)>ECD SYSTEM>CHECK FOR INTERMITTENT PROBLEMS
B
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Check if any DTCs have been stored. Note any DTCs.
Clear the DTCs (Click hereEngine / Hybrid System>N04C-VQ (ENGINE CONTROL)>ECD SYSTEM>DTC CHECK / CLEAR).
Check if the MIL goes off.
| Result | Proceed to |
|---|---|
| MIL goes off | A |
| MIL does not go off | B |
A
B
Disconnect the ECM connector.
Turn the ignition switch to ON.
Check if the MIL is illuminated.
| Result | Proceed to |
|---|---|
| MIL is not illuminated | A |
| MIL is illuminated | B |
| *a | Rear view of wire harness connector
(to ECM) |
A
B
Disconnect the combination meter assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| J1-24 (CHK) or A57-19 (W) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Start the engine.
| Result | Proceed to |
|---|---|
| Engine starts | A |
| Engine does not start* | B |
*: The GTS cannot communicate with the ECM.
B
A
Disconnect the ECM connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| A57-19 (W) - Body ground | Ignition switch ON | 11 to 14 V |
| *a | Rear view of wire harness connector
(to ECM) |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the combination meter assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| J1-24 (CHK) - A57-19 (W) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG