The fuel pressure sensor, mounted on the common rail assembly, converts the fuel pressure into an electric signal and outputs the signal to the ECM. Based on the signal from the fuel pressure sensor, the ECM controls the injection or supply pump assembly (suction control valve) and keeps the internal fuel pressure of the common rail assembly at the target fuel pressure.
| DTC No. | DTC Detection Condition | Trouble Area |
|---|---|---|
| P0087 | Conditions (a), (b) and (c) are met 10 times with engine speed 580 rpm or more (1 trip detection logic):
(a) Battery voltage: 8 V or more (b) Fuel quantify: 28 mm3/st or more (c) Amount of change in fuel pressure applied to common rail assembly: 100 kPa or less |
·
Open or short in fuel pressure sensor circuit ·
Fuel pressure sensor (built into common rail assembly) ·
ECM |
| P0190 | Conditions (a) and (b) continue for 1 seconds or more (1 trip detection logic):
(a) Ignition switch to ON (b) Open or short in fuel pressure sensor 1 circuit |
·
Open or short in fuel pressure sensor circuit ·
Fuel pressure sensor (built into common rail assembly) ·
ECM |
| Conditions (a) and (b) continue for 1 seconds or more (1 trip detection logic):
(a) Ignition switch to ON (b) Open or short in fuel pressure sensor 2 circuit |
||
| P0191 | Conditions (a) continues for 1 second (1 trip detection logic):
(a) The difference between the main and sub voltage outputs of fuel pressure sensor is below 0.04 V, or high than 1.06 V |
·
Open or short in fuel pressure sensor circuit ·
Fuel pressure sensor (built into common rail assembly) ·
ECM |
| P0192 | Condition (a) continues for 0.5 seconds or more (1 trip detection logic):
(a) Fuel pressure sensor 1 and 2 output voltage is below 0.55 V |
·
Open or short in fuel pressure sensor circuit ·
Fuel pressure sensor (built into common rail assembly) ·
ECM |
| P0193 | Condition (a) continues for 0.5 seconds or more (1 trip detection logic):
(a) Fuel pressure sensor 1 and 2 output voltage is 4.9 V or high |
·
Open or short in fuel pressure sensor circuit ·
Fuel pressure sensor (built into common rail assembly) ·
ECM |
If the vehicle runs out of fuel, and the ECM determines that the fuel pressure has decreased, DTC P0190 or P0192 may be output.
When DTC P0087, P0190, P0191, P0192 and/or P0193 are stored, check the internal fuel pressure of the common rail assembly by entering the following menus on the GTS: Powertrain / Engine and ECT / Data List / Fuel Press.
| Fuel Pressure | Malfunction |
|---|---|
| Approximately 0 kPa (0 kgf/cm2, 0 psi) | ·
Short in PCR1 and E2 termina ·
Short in PCR2 and E21 terminal ·
Open in VC circuit ·
Open in VC2 circuit |
| Approximately 190000 kPa (1937 kgf/cm2, 27557 psi) or more | ·
Short in PCR1 and VC circuit ·
Short in PCR2 and VC2 circuit ·
Open in PCR1 circuit ·
Open in PCR2 circuit ·
Open in E2 circuit ·
Open in E21 circuit |
After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>N04C-VQ (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click hereEngine / Hybrid System>N04C-VQ (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).
Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was moving or stationary, whether the engine was warmed up or not, as well as other data recorded at the time of a malfunction.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| B104-13 (VC) - B104-14 (E2) | Ignition switch ON | 4.5 to 5.5 V |
| B105-13 (VC2) - B105-14 (E21) | Ignition switch ON | 4.5 to 5.5 V |
| *a | Component with harness connected
(ECM) |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Start the engine.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B105-16 (PCR1) - B104-14 (E2) | Idling | 1.7 to 2.2 V |
| B105-2 (PCR2) - B105-14 (E21) | Idling | 1.2 to 1.6 V |
| *a | Component with harness connected
(ECM) |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the ECM connector.
Disconnect the fuel pressure sensor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B105-16 (PCR1) - m1-2 (PCR1) | Always | Below 1 Ω |
| B104-13 (VC) - m1-1 (VC1) | Always | Below 1 Ω |
| B104-14 (E2) - m1-3 (E1) | Always | Below 1 Ω |
| B105-2 (PCR2) - m1-5 (PCR2) | Always | Below 1 Ω |
| B105-13 (VC2) - m1-6 (VC2) | Always | Below 1 Ω |
| B105-14 (E21) - m1-4 (E2) | Always | Below 1 Ω |
| B105-16 (PCR1) or m1-2 (PCR1) - Body ground | Always | 10 kΩ or higher |
| B104-13 (VC) or m1-1 (VC1) - Body ground | Always | 10 kΩ or higher |
| B105-2 (PCR2) or m1-5 (PCR2) - Body ground | Always | 10 kΩ or higher |
| B105-13 (VC2) or m1-6 (VC2) - Body ground | Always | 10 kΩ or higher |
| B104-14 (E2) or m1-3 (E1) - Other terminals | Always | 10 kΩ or higher |
| B105-14 (E21) or m1-4 (E2) - Other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG