Home › Engine / Hybrid System › N04C-VQ (ENGINE CONTROL) › ECD SYSTEM
RM2850E _51 Engine / Hybrid System _073138 N04C-VQ ENGINE CONTROL _0355854 ECD SYSTEM C

N04C-VQ ENGINE CONTROL  ECD SYSTEM  P0102  Mass Air Flow Circuit Low  P0103  Mass Air Flow Circuit High  


DESCRIPTION

The intake mass air flow meter assembly consists of a platinum hot wire, temperature sensor and control circuit installed in a plastic housing. The temperature sensor (located in the intake air by-pass of the housing) detects the intake air temperature.

There is little variation in the output from the intake mass air flow meter assembly, as it is hardly affected by the resistance of the wire harness.

The internal circuit of the intake mass air flow meter assembly contains a hot wire and cold wire. A voltage is output through a bridge circuit (refer to the illumination) indicating the cooling of the hot wire according to the intake air amount. This voltage is then converted into a periodic signal by the periodic signal conversion circuit and output to the ECM. The frequency varies between approximately 1945 and 8500 Hz depending on the air flow rate. The ECM calculates the mass air flow rate based on this frequency.

A221589E01
1.667,0.506 1.900,0.704 0.232,0.198 10 +B 1.632,0.836 2.754,1.019 1.121,0.184 10 Power Transistor 2.767,1.536 3.743,1.709 0.975,0.173 10 Output Voltage 2.113,2.307 3.404,2.650 1.290,0.343 10 Periodic Signal Conversion Circuit 2.2,3.301 3.418,3.478 1.218,0.177 10 Output Frequency 0.047,2.714 1.332,3.060 1.286,0.345 10 Temperature Sensor (Thermistor) 2.106,1.158 3.818,1.362 1.711,0.205 10 Platinum Hot Wire (Heater) 3.559,2.926 5.275,3.121 1.716,0.195 10 Platinum Hot Wire (Heater) 4.983,3.269 7.121,3.452 2.137,0.184 10 Temperature Sensor (Thermistor) 2.048,1.221 1.871,1.221 1.871,1.221 1.683,1.686 false 0.526,2.687 0.526,2.071 0.526,2.071 1.298,1.783 false 2.721,1.604 2.609,1.604 2.609,1.604 2.412,1.921 false 4.084,2.874 4.084,2.454 4.084,2.454 4.54,1.865 false 6.036,3.238 6.036,2.902 6.036,2.902 4.817,2.099 false

DTC No. DTC Detection Condition Trouble Area
P0102 Mass air flow meter signal frequency is less than 850 Hz with the engine speed at less than 5000 rpm or less for 3 seconds (1 trip detection logic).
·

Open or short in mass air flow meter sub-assembly circuit

·

Mass air flow meter sub-assembly

·

ECM


P0103 Mass air flow meter signal frequency is more than 9800 Hz with the engine speed at less than 5000 rpm or less for 3 seconds (1 trip detection logic).
·

Open or short in mass air flow meter sub-assembly circuit

·

Mass air flow meter sub-assembly

·

ECM



WIRING DIAGRAM

A398541E01
1.625,1.49 1.938,1.688 0.313,0.198 10 false 2D 2.781,0.719 3.094,0.917 0.313,0.198 10 false 2D 2.771,1.063 3.083,1.26 0.313,0.198 10 false 2D 1.01,0.719 1.323,0.917 0.313,0.198 10 false 2E 1.323,0.865 2.052,1.063 0.729,0.198 10 false EFI-MAIN 2.177,1.427 2.906,1.625 0.729,0.198 10 false EFI 0.583,0.875 1.313,1.073 0.729,0.198 10 false P/I 0.385,1.719 1.427,1.927 1.042,0.208 10 false R/B NO. 2-B 0.375,2.302 1.417,2.51 1.042,0.208 10 false FL MAIN 1.052,3.042 2.094,3.25 1.042,0.208 10 false Battery 1.792,1.729 3.26,1.938 1.469,0.208 10 false No. 2 Integration Relay 3.156,0.844 3.885,1.042 0.729,0.198 10 false EFI NO. 3 3.823,1.938 4.135,2.135 0.313,0.198 10 false B51 3.813,2.094 5.177,2.729 1.365,0.635 10 false Mass Air Flow Meter Sub-assembly 5.854,2.583 6.583,2.781 0.729,0.198 10 false MREL 5.854,1.396 6.583,1.594 0.729,0.198 10 false E2G 5.875,0.917 6.604,1.115 0.729,0.198 10 false VG 4.656,1.396 5.385,1.594 0.729,0.198 10 false E2G 4.76,0.896 5.49,1.094 0.729,0.198 10 false FG 3.865,0.604 4.594,0.802 0.729,0.198 10 false +B 1.552,1.281 1.708,1.479 0.156,0.198 10 false 3 3.667,0.604 3.823,0.802 0.156,0.198 10 false 3 5.083,1.396 5.24,1.594 0.156,0.198 10 false 4 2.823,0.5 2.979,0.698 0.156,0.198 10 false 4 2.823,0.896 2.979,1.094 0.156,0.198 10 false 2 1.063,0.521 1.219,0.719 0.156,0.198 10 false 1 5.073,0.927 5.229,1.125 0.156,0.198 10 false 5 5.406,1.031 5.833,1.229 0.427,0.198 10 false B105 5.417,1.531 5.896,1.729 0.479,0.198 10 false B105 5.448,2.802 5.76,3 0.313,0.198 10 false A56 5.479,0.854 5.698,1.031 0.219,0.177 10 false 17 5.479,1.323 5.698,1.5 0.219,0.177 10 false 18 5.49,2.594 5.708,2.771 0.219,0.177 10 false 25 6.188,3.302 6.917,3.5 0.729,0.198 10 false ECM

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>N04C-VQ (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click hereEngine / Hybrid System>N04C-VQ (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).



HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was moving or stationary, whether the engine was warmed up or not, as well as other data recorded at the time of a malfunction.


PROCEDURE

1.CHECK MASS AIR FLOW METER SUB-ASSEMBLY (POWER SOURCE)
A148358E21
0.104,1.865 0.656,2.198 0.552,0.333 1.677,2.083 1.052,2.51 true 0.104,0.104 0.302,0.281 0.198,0.177 10 false *a 0.813,2.51 1.063,2.698 0.25,0.188 10 false +B 0.26,1.948 0.542,2.104 0.281,0.156 10 false B51

a.

Disconnect the mass air flow meter sub-assembly connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
B51-3 (+B) - Body ground Ignition switch ON 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Mass Air Flow Meter Sub-assembly)


Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)

NG

5.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - NO. 2 INTEGRATION RELAY)
2.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)
a.

Disconnect the mass air flow meter sub-assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B51-5 (FG) - B105-17 (VG) Always Below 1 Ω
B51-4 (E2G) - B105-18 (E2G) Always Below 1 Ω
B51-5 (FG) or B105-17 (VG) - Body ground Always 10 kΩ or higher
B51-4 (E2G) or B105-18 (EVG) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.REPLACE MASS AIR FLOW METER SUB-ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)

3.REPLACE MASS AIR FLOW METER SUB-ASSEMBLY
a.

Replace mass air flow meter sub-assembly (Click hereEngine / Hybrid System>N04C-VQ (ENGINE CONTROL)>MASS AIR FLOW METER>REMOVAL).


Result:
Proceed to
NEXT



NEXT

4.CHECK WHETHER DTC OUTPUT RECURS
4.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.



e.

Start the engine and wait for 3 seconds or more.


f.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


g.

Read the DTC.


Result:
Result Proceed to
DTC P0102 or P0103 is output A
DTC is not output B



A

B

END

5.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - NO. 2 INTEGRATION RELAY)
a.

Remove the No. 2 Integration relay from the No. 2 relay block and junction block assembly.


b.

Disconnect the mass air flow meter sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B51-3 (+B) - 2D-4 Always Below 1 Ω
B51-3 (+B) or 2D-4 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - NO. 2 INTEGRATION RELAY)