Home › Engine / Hybrid System › N04C-VQ (ENGINE CONTROL) › ECD SYSTEM
RM2850E _51 Engine / Hybrid System _073138 N04C-VQ ENGINE CONTROL _0355854 ECD SYSTEM C

N04C-VQ ENGINE CONTROL  ECD SYSTEM  P0122  Throttle / Pedal Position Sensor / Switch "A" Circuit Low Input  P0123  Throttle / Pedal Position Sensor / Switch "A" Circuit High Input  


DESCRIPTION

The throttle position sensor is mounted in the diesel throttle body assembly and detects the throttle valve (intake shutter) opening angle.

When the throttle valve is fully closed, a voltage of approximately 0.7 V is applied to terminal VLU of the ECM. The voltage applied to terminal VLU of the ECM increases in proportion to the opening angle of the throttle valve and becomes approximately 3.5 to 4.0 V when the throttle valve is fully opened. The ECM judges the vehicle driving conditions from these signals input from terminal VLU, and uses them as one of the conditions for deciding the EGR control, etc.

A429929E01
2.646,1.865 2.813,0.542 2.813,0.542 2.979,0.542 true 2.5,1.333 2.26,0.542 2.26,0.542 2.115,0.542 true 2.51,2.552 1.74,3.021 1.74,3.021 1.573,3.021 true 1.583,0.448 2.5,0.646 0.917,0.198 10 false Magnet 3.042,0.458 3.771,0.646 0.729,0.188 10 false Hall IC 3.323,1.104 3.708,1.271 0.385,0.167 10 false VC 3.781,1.104 4.167,1.271 0.385,0.167 10 false VC 4.573,0.99 4.958,1.156 0.385,0.167 10 false 5 V 3.344,1.76 3.792,1.927 0.448,0.167 10 false VTA 3.719,1.76 4.167,1.927 0.448,0.167 10 false VLU 3.344,2.406 3.656,2.573 0.313,0.167 10 false E2 3.771,2.406 4.083,2.573 0.313,0.167 10 false E2 4.573,3.115 5.188,3.313 0.615,0.198 10 false ECM 1.063,2.917 1.979,3.115 0.917,0.198 10 false Magnet 1.917,3.125 3.677,3.354 1.76,0.229 10 false Throttle Position Sensor

DTC No. DTC Detection Condition Trouble Area
P0122 Open or short in throttle position sensor circuit for 3 second
·

Open or short in throttle position sensor circuit

·

Throttle position sensor (built into diesel throttle body assembly)

·

ECM


P0123 Open or short in throttle position sensor circuit for 3 second
·

Open or short in throttle position sensor circuit

·

Throttle position sensor (built into diesel throttle body assembly)

·

ECM



WIRING DIAGRAM

A398534E05
1.833,0.583 2.146,0.781 0.313,0.198 10 false VC 5.469,0.604 5.781,0.802 0.313,0.198 10 false VC 1.771,1.073 2.167,1.271 0.396,0.198 10 false VTA 5.458,1.083 5.854,1.281 0.396,0.198 10 false VLU 1.875,1.542 2.271,1.74 0.396,0.198 10 false E2 5.458,1.542 5.854,1.74 0.396,0.198 10 false E2 2.219,0.958 2.521,1.156 0.302,0.198 10 false 3 2.208,0.479 2.51,0.677 0.302,0.198 10 false 1 2.208,1.406 2.51,1.604 0.302,0.198 10 false 2 5.125,0.479 5.427,0.677 0.302,0.198 10 false 13 5.146,1.417 5.448,1.615 0.302,0.198 10 false 14 5.188,0.948 5.49,1.146 0.302,0.198 10 false 3 0.729,2.083 1.188,2.271 0.458,0.188 10 false B27 0.729,2.292 2.542,2.531 1.813,0.24 10 false Thorottle Position Sensor 5.896,2.073 6.417,2.292 0.521,0.219 10 false B104 5.896,2.302 6.417,2.521 0.521,0.219 10 false ECM

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>N04C-VQ (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click hereEngine / Hybrid System>N04C-VQ (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).


HINT:
·

If DTCs that are related to different systems are output simultaneously while terminal E2 is used as a ground terminal, terminal E2 may have an open circuit.

·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was moving or stationary, whether the engine was warmed up or not, as well as other data recorded at the time of a malfunction.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (ECM - THROTTLE POSITION SENSOR)
a.

Disconnect the throttle position sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B27-1 (VC) - B104-13 (VC) Always Below 1 Ω
B27-3 (VTA) - B104-3 (VLU) Always Below 1 Ω
B27-2 (E2) - B104-14 (E2) Always Below 1 Ω
B27-1 (VC) or B104-13 (VC) - Body ground Always 10 kΩ or higher
B27-3 (VTA) or B104-3 (VLU) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.INSPECT ECM (VC VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - THROTTLE POSITION SENSOR)

2.INSPECT ECM (VC VOLTAGE)
a.
A260250E34
1.844,0.188 2.333,0.448 0.49,0.26 1.948,1.615 2.177,0.875 true 2.552,1.615 2.229,0.875 true 0.156,0.094 0.469,0.292 0.313,0.198 10 false *a 1.906,0.24 2.417,0.448 0.51,0.208 10 false B104 1.604,1.667 2.188,1.875 0.583,0.208 10 false 14 (E2) 2.365,1.667 2.948,1.875 0.583,0.208 10 false 13 (VC)

Turn the ignition switch to ON.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
B104-13 (VC) - B104-14 (E2) Ignition switch ON 4.5 to 5.5 V


Text in Illustration
*a Component with harness connected
(ECM)


Result:
Proceed to
OK
NG



OK

3.REPLACE DIESEL THROTTLE BODY ASSEMBLY (THROTTLE POSITION SENSOR)

NG

3.REPLACE DIESEL THROTTLE BODY ASSEMBLY (THROTTLE POSITION SENSOR)
a.

Replace the diesel throttle body assembly (Click hereEngine / Hybrid System>N04C-VQ (ENGINE CONTROL)>DIESEL THROTTLE BODY>REMOVAL).


Result:
Proceed to
NEXT



NEXT

4.CHECK WHETHER DTC OUTPUT RECURS
4.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Read the DTCs.


Result:
Result Proceed to
DTC P0122 or P0123 is output A
DTC is not output B



A

B

END