Home › Engine / Hybrid System › N04C-VQ (ENGINE CONTROL) › ECD SYSTEM
RM2850E _51 Engine / Hybrid System _073138 N04C-VQ ENGINE CONTROL _0355854 ECD SYSTEM C

N04C-VQ ENGINE CONTROL  ECD SYSTEM  P0168  Fuel Temperature Too High  P0180  Fuel Temperature Sensor "A" Circuit  P0182  Fuel Temperature Sensor "A" Circuit Low Input  P0183  Fuel Temperature Sensor "A" Circuit High Input  


DESCRIPTION

The fuel temperature sensor senses the fuel temperature. A thermistor built into the sensor changes its resistance value according to the fuel temperature. The lower the fuel temperature is, the greater the thermistor resistance becomes, and the higher the fuel temperature is, the lower the thermistor resistance becomes (see Fig. 1).

The fuel temperature sensor is connected to the ECM. The 5 V power source voltage in the ECM is applied to the fuel temperature sensor from terminal THF via resistor R. The resistor R and the fuel temperature sensor are connected in series. When the resistance value of the fuel temperature sensor changes in accordance with the fuel temperature, the voltage at terminal THF also changes. Based on this signal, the ECM corrects the pressure control compensation of the injection or supply pump assembly and an error.

A283580E22
3.354,2.271 3.74,1.99 false 2.26,0.406 2.833,0.667 0.573,0.26 10 Fig. 1: 3.292,4.271 4.167,4.5 0.875,0.229 10 Temperature 2.396,0.969 2.771,1.219 0.375,0.25 10 (kΩ) 2.281,1.146 2.521,1.365 0.24,0.219 10 30 2.281,1.583 2.521,1.802 0.24,0.219 10 10 2.354,1.875 2.594,2.094 0.24,0.219 10 5 2.354,2.094 2.594,2.313 0.24,0.219 10 3 2.354,2.26 2.51,2.479 0.156,0.219 10 2 2.344,2.531 2.594,2.75 0.25,0.219 10 1 2.24,2.833 2.479,3.052 0.24,0.219 10 0.5 2.24,3.198 2.479,3.417 0.24,0.219 10 0.2 2.24,3.469 2.479,3.688 0.24,0.219 10 0.1 2.281,1.323 2.531,1.542 0.25,0.219 10 20 2.542,3.823 2.781,4.042 0.24,0.219 10 -20 2.938,3.823 3.177,4.042 0.24,0.219 10 0 3.208,3.823 3.448,4.042 0.24,0.219 10 20 3.521,3.823 3.76,4.042 0.24,0.219 10 40 3.833,3.823 4.073,4.042 0.24,0.219 10 60 4.146,3.823 4.385,4.042 0.24,0.219 10 80 4.385,3.823 4.625,4.042 0.24,0.219 10 100 2.583,4 2.823,4.219 0.24,0.219 10 -4 2.896,4 3.135,4.219 0.24,0.219 10 32 3.208,4 3.448,4.219 0.24,0.219 10 68 3.479,4 3.729,4.25 0.25,0.25 10 104 3.792,4 4.125,4.25 0.333,0.25 10 140 4.094,4 4.417,4.25 0.323,0.25 10 176 4.385,4 4.708,4.25 0.323,0.25 10 212 4.677,3.823 5,4.073 0.323,0.25 10 (°C) 4.677,4 5,4.25 0.323,0.25 10 (°F) 3.802,1.896 4.583,2.167 0.781,0.271 10 Acceptable 2.26,0.719 3.083,0.917 0.823,0.198 10 Resistance 2.24,3.021 2.479,3.24 0.24,0.219 10 0.3

DTC No. DTC Detection Condition Trouble Area
P0168 After engine is warmed up, conditions (a), (b) and (c) continue for more than 1 second (1 trip detection logic):

(a) Engine speed: 1000 rpm or more

(b) Vehicle speed: 10 km/h (6 mph) or more

Fuel temperature: 88°C (190°F) or more


·

Open or short in fuel temperature sensor circuit

·

Fuel temperature sensor (built into injection or supply pump assembly)

·

ECM


P0180 Open or short in fuel temperature sensor circuit for 0.5 seconds (1 trip detection logic).
·

Open or short in fuel temperature sensor circuit

·

Fuel temperature sensor (built into injection or supply pump assembly)

·

ECM


P0182 Short in fuel temperature sensor circuit for 0.5 seconds (1 trip detection logic).
·

Short in fuel temperature sensor circuit

·

Fuel temperature sensor (built into injection or supply pump assembly)

·

ECM


P0183 Open in fuel temperature sensor circuit for 0.5 seconds (1 trip detection logic).
·

Open in fuel temperature sensor circuit

·

Fuel temperature sensor (built into injection or supply pump assembly)

·

ECM



HINT:

When DTC P0180, P0182 or P0183 is detected, check the fuel temperature by entering the following menus on the GTS: Powertrain / Engine and ECT / Data List / Fuel Temperature.

Temperature Displayed Malfunction
-40°C (-40°F) Open circuit
140°C (284°F) or more Short circuit


WIRING DIAGRAM

A398533E09
1.615,1.208 2.073,1.406 0.458,0.198 10 false THF 1.656,1.792 1.979,1.979 0.323,0.188 10 false E2 2.01,1.219 2.333,1.406 0.323,0.188 10 false 2 2,1.792 2.323,1.979 0.323,0.188 10 false 1 0.333,2.542 0.656,2.729 0.323,0.188 10 false B8 0.344,2.75 2.74,3.146 2.396,0.396 10 false Fuel Temperature Sensor (Built into Injection or Supply Pump Assembly) 5.073,1.115 5.396,1.302 0.323,0.188 10 false 4 4.969,1.333 5.469,1.521 0.5,0.188 10 false B105 4.958,1.896 5.448,2.083 0.49,0.188 10 false B104 5.031,1.677 5.354,1.865 0.323,0.188 10 false 14 5.438,1.219 5.896,1.417 0.458,0.198 10 false THF 5.469,1.802 5.792,1.99 0.323,0.188 10 false E2 6.156,0.844 6.615,1.042 0.458,0.198 10 false 5 V 6.104,1.125 6.406,1.302 0.302,0.177 10 false R 5.958,2.823 6.531,3.042 0.573,0.219 10 false ECM

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>N04C-VQ (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click hereEngine / Hybrid System>N04C-VQ (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).


HINT:
·

If DTCs that are related to different systems are output simultaneously while terminal E2 is used as a ground terminal, terminal E2 may have an open circuit.

·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was moving or stationary, whether the engine was warmed up or not, as well as other data recorded at the time of a malfunction.



PROCEDURE

1.READ VALUE USING GTS (FUEL TEMPERATURE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Fuel Temperature.


e.

Read the value.

Standard:

Same value as the actual fuel temperature.


Result:
Temperature Display Proceed to
-40°C (-40°F) A
140°C (284°F) or more B
OK (same as actual fuel temperature) C


HINT:
·

If there is an open circuit, the GTS indicates -40°C (-40°F).

·

If there is a short circuit, the GTS indicates 140°C (284°F) or more.





A

2.READ VALUE USING GTS (CHECK FOR OPEN IN WIRE HARNESS)

B

4.READ VALUE USING GTS (CHECK FOR SHORT IN WIRE HARNESS)

C

2.READ VALUE USING GTS (CHECK FOR OPEN IN WIRE HARNESS)
a.
A256062E04
0.5,0.552 0.906,0.802 0.406,0.25 0.833,1.333 1.458,1.094 true 1.958,1.083 2.563,1.406 true 0.125,0.083 0.438,0.281 0.313,0.198 10 false *a 0.625,0.594 1,0.813 0.375,0.219 10 false B8 0.573,1.26 0.948,1.458 0.375,0.198 10 false E2 2.635,1.354 3.104,1.552 0.469,0.198 10 false THF

Disconnect the fuel temperature sensor connector.


b.

Connect terminals 1 (E2) and 2 (THF) of the wire harness side connector.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Enter the following menus: Powertrain / Engine and ECT / Data List / Fuel Temperature.


g.

Read the value.

Standard:

140°C (284°F) or more


Text in Illustration
*a Front view of wire harness connector
(to Fuel Temperature Sensor)


Result:
Proceed to
OK
NG



OK

REPLACE INJECTION OR SUPPLY PUMP ASSEMBLY (FUEL TEMPERATURE SENSOR)

NG

3.READ VALUE USING GTS (CHECK FOR OPEN IN ECM)
3.READ VALUE USING GTS (CHECK FOR OPEN IN ECM)
a.
A260250E36
1.302,0.104 1.792,0.396 0.49,0.292 1.844,0.104 2.333,0.396 0.49,0.292 2.177,0.875 2.333,1.74 true 1.521,0.729 1,1.74 true 1.396,0.167 1.813,0.323 0.417,0.156 10 false B105 1.938,0.167 2.417,0.323 0.479,0.156 10 false B104 0.063,0.073 0.25,0.281 0.188,0.208 10 false *a 2.146,1.771 2.844,2.01 0.698,0.24 10 false 14 (E2) 0.771,1.771 1.406,2.042 0.635,0.271 10 false 4 (THF)

Disconnect the fuel temperature sensor connector.


b.

Connect terminals THF and E2 of the ECM connector.

HINT:

Before checking, do a visual and contact pressure check for the ECM connector.



c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Enter the following menus: Powertrain / Engine and ECT / Data List / Fuel Temperature.


g.

Read the value.

Standard:

140°C (284°F) or more


Text in Illustration
*a Component with harness connected
(ECM)


Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - FUEL TEMPERATURE SENSOR)

NG

4.READ VALUE USING GTS (CHECK FOR SHORT IN WIRE HARNESS)
a.

Disconnect the fuel temperature sensor connector.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Engine and ECT / Data List / Fuel Temperature.


f.

Read the value.

Standard:

-40°C (-40°F)



Result:
Proceed to
OK
NG



OK

REPLACE INJECTION OR SUPPLY PUMP ASSEMBLY (FUEL TEMPERATURE SENSOR)

NG

5.CHECK HARNESS AND CONNECTOR (ECM - FUEL TEMPERATURE SENSOR)
5.CHECK HARNESS AND CONNECTOR (ECM - FUEL TEMPERATURE SENSOR)
a.

Disconnect the fuel temperature sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the valve(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B105-4 (THF) or B8-2 (THF) - Body ground Always 10 kΩ or higher
B104-14 (E2) or B8-1 (E2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - FUEL TEMPERATURE SENSOR)