Home › Engine / Hybrid System › N04C-VQ (ENGINE CONTROL) › ECD SYSTEM
RM2850E _51 Engine / Hybrid System _073138 N04C-VQ ENGINE CONTROL _0355854 ECD SYSTEM C

N04C-VQ ENGINE CONTROL  ECD SYSTEM  P1458  EGR Actuator Minor Malfunction  P1459  EGR Actuator Major Malfunction  


DESCRIPTION

DTC No. DTC Detection Condition Trouble Area
P1458 The EGR valve assembly outputs an abnormal signal a certain amount of times while the engine is running.
(1 trip detection logic)
·

Open or short in EGR valve assembly circuit

·

EGR valve assembly

·

ECM


P1459 The EGR valve assembly outputs an abnormal signal a certain amount of times while the engine is running.
(1 trip detection logic)
·

Open or short in EGR valve assembly circuit

·

EGR valve assembly

·

ECM



WIRING DIAGRAM

A398540E05
1.333,2.323 3.021,2.51 1.688,0.188 10 false EGR Valve Assembly 2.094,0.417 2.604,0.625 0.51,0.208 10 false CANH 2.115,0.865 2.583,1.073 0.469,0.208 10 false CANL 2.333,1.302 2.594,1.469 0.26,0.167 10 false E 2.281,1.729 2.542,1.938 0.26,0.208 10 false B+ 1.344,2.125 1.813,2.333 0.469,0.208 10 false B48 5.573,0.865 6.042,1.073 0.469,0.208 10 false B104 5.573,0.427 6.042,0.635 0.469,0.208 10 false B104 6.031,0.427 6.5,0.635 0.469,0.208 10 false CAN+ 6.021,0.875 6.49,1.083 0.469,0.208 10 false CAN- 4.479,2.427 5.229,2.625 0.75,0.198 10 false EFI NO. 3 6.021,3.948 6.49,4.156 0.469,0.208 10 false MREL 2.99,4.74 4.531,5.021 1.542,0.281 10 false No. 2 Integration Relay 1.25,4.833 1.948,5.042 0.698,0.208 10 false Battery 0.667,3.979 1.365,4.188 0.698,0.208 10 false FL MAIN 0.667,3.583 1.573,3.76 0.906,0.177 10 false R/B NO. 2-B 1.688,3.583 2.156,3.792 0.469,0.208 10 false P/I 2.51,3.438 2.865,3.646 0.354,0.208 10 false 2E 2.5,3.927 2.844,4.135 0.344,0.208 10 false 2D 4.677,3.938 5.083,4.146 0.406,0.208 10 false 2D 4.677,3.438 5.146,3.646 0.469,0.208 10 false 2D 5.615,3.938 6.083,4.146 0.469,0.208 10 false A56 3.896,4.24 4.365,4.448 0.469,0.208 10 false EFI 6.188,4.979 6.656,5.188 0.469,0.208 10 false ECM 2.542,3.219 2.823,3.427 0.281,0.208 10 false 1 2.542,3.729 2.802,3.906 0.26,0.177 10 false 3 4.719,3.74 5.125,3.979 0.406,0.24 10 false 2 4.719,3.24 4.927,3.427 0.208,0.188 10 false 4 2.594,1.188 2.854,1.417 0.26,0.229 10 false 1 2.594,0.281 2.854,0.479 0.26,0.198 10 false 5 2.604,0.719 2.875,0.906 0.271,0.188 10 false 2 2.594,1.625 2.885,1.854 0.292,0.229 10 false 4 5.667,0.229 6.073,0.469 0.406,0.24 10 false 12 5.708,0.677 6.115,0.917 0.406,0.24 10 false 6 5.656,3.729 6.063,3.969 0.406,0.24 10 false 25 2.927,3.583 3.625,3.792 0.698,0.208 10 false EFI-MAIN

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>N04C-VQ (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click hereEngine / Hybrid System>N04C-VQ (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was moving or stationary, whether the engine was warmed up or not, as well as other data recorded at the time of a malfunction.


PROCEDURE

1.CHECK EGR VALVE ASSEMBLY (POWER SOURCE)
a.
A430807E02
1.521,0.302 1.938,0.563 0.417,0.26 0.823,0.708 1.479,1.083 true 0.917,1.667 1.5,1.354 true 0.146,0.146 0.458,0.344 0.313,0.198 10 false *a 0.635,0.583 0.948,0.781 0.313,0.198 10 false E 0.656,1.604 0.969,1.802 0.313,0.198 10 false +B 1.594,0.344 2.063,0.542 0.469,0.198 10 false B48

Disconnect the EGR valve assembly connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
B48-4 (+B) - B48-1 (E) Ignition switch ON 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to EGR Valve Assembly)


Result:
Proceed to
OK
NG



OK

2.INSPECT EGR VALVE ASSEMBLY

NG

5.CHECK HARNESS OR CONNECTOR (EGR VALVE ASSEMBLY - BODY GROUND)
2.INSPECT EGR VALVE ASSEMBLY

Result:
Proceed to
OK
NG



OK

3.REPLACE ECM

NG

3.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

4.CHECK WHETHER DTC OUTPUT RECURS
4.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Read the DTCs.


Result:
Result Proceed to
DTC is not output A
DTC P1458 or P1459 is output B



A

END

B

5.CHECK HARNESS OR CONNECTOR (EGR VALVE ASSEMBLY - BODY GROUND)
a.

Disconnect the EGR valve assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B48-1 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (EGR VALVE ASSEMBLY - NO. 2 INTEGRATION RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (EGR VALVE ASSEMBLY - BODY GROUND)

6.CHECK HARNESS AND CONNECTOR (EGR VALVE ASSEMBLY - NO. 2 INTEGRATION RELAY)
a.

Disconnect the EGR valve assembly connector.


b.

Remove the No. 2 integration relay from the No. 2 relay block and junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B48-4 (+B) - 2D-4 Always Below 1 Ω
B48-4 (+B) or 2D-4 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (EGR VALVE ASSEMBLY - NO. 2 INTEGRATION RELAY)