1.INSTALL CAMSHAFT BEARING
Be sure to face the notches of the No. 1 and No. 2 bearings and oil holes of the No. 3 bearing in the correct direction.
| *1 | Notch |
| *2 | Oil Hole |
Using SST, install new camshaft bearings in the direction indicated by the arrow marks in the illustration.
| Journal No. | Inside Diameter | Outside Diameter |
|---|---|---|
| No. 1 | 57.0 mm (2.2441 in.) | 60.0 mm (2.3622 in.) |
| No. 2 | 56.8 mm (2.2362 in.) | 59.8 mm (2.3543 in.) |
| No. 3 | 56.6 mm (2.2283 in.) | 59.6 mm (2.3465 in.) |
|
Front |
Install the bearings No. 2, No. 1 and No. 3 in order.
13201A
2.INSTALL CONNECTING ROD SMALL END BUSH
Uniformly chamfer one edge of the bush hole at the small end of the connecting rod.
Irregular chamfering can cause out-of-round of the bush, which may result in jamming during the insertion.
Remove dust from the inner surface of the connecting rod hole.
Mount a new bush on the spindle.
6.0 N*m (61 kgf*cm, 53 in.*lbf)
| *1 | Groove |
| *2 | Oil Hole |
| *3 | Bush |
Align the oil holes in the bush with both grooves of the spindle and guide, and make sure that oil holes will meet with the oil path in the connecting rod leading from the big end bore in the rod.
Set SST on a level workbench.
Assemble the guide and press sub-assembly by inserting its pin into the guide, then secure them with the wing nut.
Orient the letter W, stamped on the guide, above the pin.
Align both supporting surfaces of the guide and press sub-assembly on a level workbench.
| *1 | Connecting Rod |
| *a | Guide |
| *b | Press Sub-assembly |
| *c | Groove |
| *d | Center of the Connecting Rod |
Place the connecting rod so that the groove of SST (press sub-assembly) is aligned with the center of the connecting rod.
Place the connecting rod so that the chamfering side faces up.
Install the bush into the connecting rod. Position the spindle and bush so that the oil holes align with the oil path through the connecting rod.
| *1 | Groove |
| *2 | Oil Hole |
Inspect the bush position after installation.
Make sure that the oil hole of the bush and the oil path of the connecting rod are suitably aligned allowing a 6 mm (0.236 in.) diameter rod to penetrate.
Misalignment can lead to insufficient lubrication, which may result in seizure.
13101A
3.INSTALL PISTON PIN HOLE SNAP RING
Using snap ring pliers, install a new snap ring into one side of the piston hole.
4.INSTALL PISTON
Before assembling the piston with the connecting rod, check whether the piston is specified for this engine. The check should be performed using the engine compatible identification code on the top of the piston.
95
Assemble the piston and connecting rod.
Gradually heat the piston to approximately 50°C (122°F).
Do not touch the piston while it is hot.
Coat the piston pin with engine oil.
Install the piston onto the connecting rod with the notch on the piston facing in the same direction as the alignment mark on the rod.
| *1 | Notch |
| *a | Alignment Mark |
| *b | Matchmark |
Match the matchmarks on the piston and piston pin, and then insert the piston pin.
Check that the piston and piston pin fit securely.
Try to move the piston back and forth.
Using snap ring pliers, install a new snap ring into the other side of the piston pin hole.
13011
5.INSTALL PISTON RING SET
Using a piston ring expander, install them in the following order of the oil ring, 2nd ring and 1st ring.
Attach the second ring so that the stamp mark is on the upper side.
Never change the combination of the coil and oil ring.
Connect the joint of the coil expander for the oil ring and install it inside the oil ring. Align the expander joint 180° opposite to the gap of the ring.
15708
6.INSTALL NO. 1 OIL NOZZLE SUB-ASSEMBLY
Install the No. 1 oil nozzle sub-assembly with the bolt.
29 N*m (291 kgf*cm, 21 ft.*lbf)
If the oil nozzle has been dropped or any impact has occurred to the nozzle, replace the nozzle with a new one.
Replace a deformed nozzle with a new one.
15605
7.INSTALL OIL CHECK VALVE SUB-ASSEMBLY
Install a new gasket and the oil check valve sub-assembly.
69 N*m (699 kgf*cm, 51 ft.*lbf)
11702
8.INSTALL CRANKSHAFT BEARING SET
Match the upper bearing with an oil groove to the oil hole and concave section, attach it to the cylinder block, and then apply engine oil.
| *a | Oil Hole |
| *b | Oil Groove |
Keep the back side of the bearing and the bearing surface free of foreign matter.
Do not apply engine oil to the attachment surface and the back surface of the bearing.
Check that the oil holes are aligned.
Misaligned oil holes can lead to a lack of oil, causing seizure.
Attach the lower bearing to the convex section on the crankshaft bearing cap and apply engine oil.
| *a | Convex Section |
Keep the back side of the bearing and the bearing surface free of foreign matter.
Do not apply engine oil to the attachment surface and the back surface of the bearing.
Face the oil groove surface of the thrust washer outwards and attach it to the crankshaft bearing cap. And then, apply engine oil.
Install the crankshaft.
Insert the thrust washer into the clearance between the cylinder block and crankshaft with the oil groove facing outward.
| *1 | Groove |
Install the main bearing cap onto the cylinder block.
The bearing caps must be installed so that the pentagonal marks on the bearing caps face the front of the engine, and that they are arranged in sequential order (1-2-3-4-5) from the front side.
Apply a light coat of engine oil to the threads and under the cap bolt.
Be sure to install the removed thrust washer to its original position.
Temporarily tighten the 10 cap bolts in 2 to 3 steps, in the sequence shown in the illustration.
Tighten the cap bolts to the specified torque, in the sequence shown in the illustration.
60 N*m (612 kgf*cm, 44 ft.*lbf)
Loosen the bearing cap in the position of the thrust washer and use a plastic hammer to lightly tap the front and back ends of the crankshaft.
Loosen the 10 cap bolts.
Tighten the 10 cap bolts in 2 to 3 steps, in the sequence shown in the illustration.
60 N*m (612 kgf*cm, 44 ft.*lbf)
Mark the front of the bearing cap bolts with paint.
| *a | Paint Mark |
|
Front |
Retighten the bolts by 60° and then an additional 60° as shown in the sequence shown in the illustration.
Do not loosen to return the bolts in position if they have been tightened too much.
Check that all the paint marks face the same direction.
After tightening, use a plastic hammer to lightly tap both the front and rear ends of the crankshaft.
Check that the crankshaft rotates smoothly.
11462
9.INSTALL CYLINDER LINER
When assembling the cylinder liner into the cylinder block, the clearance can be set to 3 levels.
The upper surface and side surface of the cylinder block are stamped A, B or C. When using a new cylinder liner, insert a matching cylinder liner with the same symbol.
| *a | Position of Mark A, B or C |
Apply engine oil to the cylinder block inside bore.
Align the marks of the cylinder liner and cylinder block.
| *a | Mark |
When reusing the cylinder liner, install it according to the marks made during the removal. When reusing the cylinder liner, misalignment with the cylinder block may concentrate stress on the thin part of the cylinder liner and it may break.
Install the cylinder liner.
Make sure to install the cylinder liner to its original location.
10.INSTALL PROTRUSION OF CYLINDER LINER
Mount SST onto the cylinder block.
Tighten the center bolt to the specified torque below to set the SST in the proper installation position.
9.8 N*m (100 kgf*cm, 87 in.*lbf)
Using a dial indicator, measure the protrusion of the cylinder liner.
0.01 to 0.08 mm (0.000394 to 0.00315 in.)
0.08 mm (0.00315 in.)
|
If the protrusion is greater than the maximum, replace the cylinder liner. |
|
| *a | Protrusion |
13202
11.INSTALL CONNECTING ROD BEARING
When reusing the bearing, reassemble the removed bearing as it was originally installed.
Install the bearing with the oil hole onto the connecting rod side and install the bearing without the oil hole onto the cap side.
Match the bearing protrusion with the notch of the connecting rod or cap.
Keep the back side of the bearing and bearing surface of the bearing cap free of foreign matter.
Do not apply engine oil to the attachment surface and the back surface of the bearing.
| *a | Protrusion |
12.INSTALL PISTON WITH CONNECTING ROD
Position the gaps of the piston rings at an even distance. Be careful not to position the gaps at the same position as the piston mark.
| *1 | Mark |
| *2 | 1st Ring |
| *3 | 2nd Ring |
| *4 | Oil Ring |
Place the crankshaft for the cylinder where the piston with connecting rod is to be attached in the TDC.
If the crankshaft is in a position other than the TDC, the connecting rod may interfere with the No. 1 oil nozzle.
Using a piston ring compressor and a hammer handle, insert the piston with connecting rod assembly into the cylinder block.
Insert the piston and connecting rod to the matching cylinder using the cylinder identification numbers.
Check that there are no deformations or damage to the piston ring compressor.
Before the installation, apply engine oil to the piston pin, piston ring, cylinder liner and connecting rod bearing.
Check the gap of each piston ring.
Be careful not to damage the cylinder liner, crankshaft, and No. 1 oil nozzle during the operation.
Make sure that the mark on the piston is on the tappet chamber side.
| *1 | Mark |
| *2 | Tappet Chamber |
Align the matchmarks and install the bearing cap onto the connecting rod with the front mark facing in the correct direction.
| *a | Matchmark |
Uniformly install and tighten the 2 bolts to the specified torque in 2 to 3 steps.
30 N*m (306 kgf*cm, 22 ft.*lbf)
Mark the front side of the bolt head with paint.
| *a | Paint Mark |
|
Front |
Retighten the bolts by 60° as shown in the illustration.
Perform step (e) again.
Check that each painted mark is now at a 120° angle to the front.
11381A
13.INSTALL REAR ENGINE OIL SEAL
Using SST and a hammer, tap in a new engine rear oil seal until it is 4 mm (0.157 in.) below the upper edge of the flywheel housing.
| *a | 4 mm (0.157 in.) |
Be careful not to tap the oil seal at an angle.
Keep the gap between the rear oil seal retainer edge and the oil seal free of foreign matter.
Apply MP grease to the oil seal lip.
11351
14.INSTALL FLYWHEEL HOUSING
Remove any old seal packing material from the contact surface.
Apply a continuous bead of seal packing (diameter: 1.5 to 2.5 mm (0.0591 to 0.0984 in)) as shown in the illustration.
Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent
| *1 | Seal Packing |
Remove any oil from the contact surface.
Install the flywheel housing within 3 minutes of applying the seal packing.
Do not expose the seal packing to engine oil for at least 2 hours after installing.
Install the flywheel housing with the 14 bolts.
132 N*m (1346 kgf*cm, 97 ft.*lbf)
29 N*m (291 kgf*cm, 21 ft.*lbf)
13453
15.INSTALL FLYWHEEL RING GEAR
Using a torch, heat the ring gear evenly to approximately 200°C (392°F).
| *1 | Chamfer |
| *2 | Ring Gear |
| *3 | Flywheel |
Be careful not to overheat the ring gear.
Using a brass bar, strike the ring gear onto the flywheel with its chamfered gear teeth facing the block.
0.25 mm (0.00984 in.)
After installing, allow the ring gear to cool before handling.
13450A
16.INSTALL FLYWHEEL SUB-ASSEMBLY
Insert the flywheel slowly until it contacts the collar knock in order to prevent impact with the guide bar. Adjust the position, then insert it completely.
The flywheel is heavy. When installing, be careful not to drop it.
Apply clean engine oil to the threads of the flywheel bolts and the flywheel bolt seats.
Insert a screwdriver through the inspection hole of the flywheel housing into the ring gear of the flywheel to keep it from turning together with the crankshaft.
Tighten the flywheel bolts in several steps in the order shown in the illustration.
86 N*m (877 kgf*cm, 63 ft.*lbf)
Mark the front of the flywheel bolts with paint.
| *a | Paint Mark |
| *b | 45° |
Tighten the flywheel bolts 45°in several steps in the order shown in the illustration.
Check that the paint marks are now at a 45°angle to the front.
Using a dial indicator, measure the runout of the flywheel sub-assembly.
0.15 mm (0.00591 in.)
If the runout is greater than the maximum, resurface the sliding surface.
Temporarily install 4 bolts in the positions of the cylinder block shown in the illustration to prevent the wires from sliding toward the center of the block.
Attach 2 wires to the cylinder block.
The wires must be attached outside the installed bolts.
Using a chain block and an engine sling device, install the cylinder block onto the engine stand.
Remove the 4 bolts from the cylinder block.
11311H
17.INSTALL FRONT END PLATE
Install the front end plate with a new front end plate gasket and 4 bolts.
29 N*m (291 kgf*cm, 21 ft.*lbf)
Using a cutter, cut the gasket so that it is flush with the lower surface of the cylinder block.
15100
18.INSTALL OIL PUMP ASSEMBLY
19.INSTALL CRANKSHAFT TIMING GEAR OR SPROCKET
Turn the crankshaft clockwise, and align the matchmarks of the flywheel sub-assembly and flywheel housing to set the No. 1 cylinder to TDC.
| *a | TDC of No. 1 and No. 4 Cylinders |
| *b | Matchmark |
Align the set key on the crankshaft with the key groove of the crankshaft timing gear.
Using a hammer, tap in the crankshaft timing gear.
13508M
20.INSTALL NO. 1 IDLE GEAR SUB-ASSEMBLY
Install the idle gear and idle gear thrust plate onto the idle gear shaft.
| *1 | Oil Hole |
With the idle gear shaft oil hole facing down, match the alignment marks for each gear, and insert the shaft into the cylinder block.
| *a | Alignment Mark |
If the oil hole is not facing down, it will cause burning or abnormal wear.
Tighten the bolt.
137 N*m (1397 kgf*cm, 101 ft.*lbf)
13501
21.INSTALL CAMSHAFT
13581C
22.INSTALL NO. 2 IDLE GEAR SHAFT
Install the lock plate onto the front end plate with the bolt.
29 N*m (291 kgf*cm, 21 ft.*lbf)
| *1 | Oil Hole |
Install a new O-ring onto the No. 2 idle gear shaft.
With the idle gear shaft oil hole facing down, install the No. 2 idle gear shaft onto the lock plate with the 3 bolts.
55 N*m (561 kgf*cm, 41 ft.*lbf)
If the oil hole is not facing down, it will cause burning or abnormal wear.
13508N
23.INSTALL NO. 2 IDLE GEAR SUB-ASSEMBLY
Match the alignment marks of the No. 1 and No. 2 idle gear sub-assemblies and install the No. 2 idle gear shaft.
| *a | Alignment Mark |
13572C
24.INSTALL NO. 2 IDLE GEAR THRUST PLATE
Install the No. 2 idle gear thrust plate with the 2 bolts.
55 N*m (561 kgf*cm, 41 ft.*lbf)
11301C
25.INSTALL TIMING CHAIN OR BELT COVER OIL SEAL
26.INSTALL TIMING GEAR CASE
13470
27.INSTALL CRANKSHAFT PULLEY ASSEMBLY
12270
28.INSTALL OIL SEPARATOR ASSEMBLY
Install 3 new O-rings onto the timing gear case and cylinder block.
Install the oil separator assembly with the 5 bolts.
55 N*m (561 kgf*cm, 41 ft.*lbf)
15104
29.INSTALL OIL STRAINER SUB-ASSEMBLY
Install a new O-ring onto the cylinder block.
Install the oil strainer sub-assembly with the 2 bolts.
29 N*m (291 kgf*cm, 21 ft.*lbf)
12101
30.INSTALL OIL PAN SUB-ASSEMBLY
11351H
31.INSTALL FLYWHEEL HOUSING STAY RH
11351G
32.INSTALL FLYWHEEL HOUSING STAY LH
13751
33.INSTALL VALVE LIFTER
Be sure to install the removed valve lifter in its original position.
11115
34.INSTALL CYLINDER HEAD GASKET
11101
35.INSTALL CYLINDER HEAD SUB-ASSEMBLY
13819
36.INSTALL VALVE BRIDGE
Be sure to install the removed valve bridge to its original location.
13781
37.INSTALL VALVE PUSH ROD
Be sure to install the removed valve push rod to its original location.
13901
38.INSTALL NO. 1 VALVE ROCKER SHAFT SUB-ASSEMBLY
39.ADJUST VALVE CLEARANCE
Turn the crankshaft clockwise to align the alignment marks on the flywheel sub-assembly with the line between the 2 numbers on the edge on the flywheel housing.
| *a | TDC of No. 1 and No. 4 Cylinders |
| *b | TDC of No. 2 and No. 3 Cylinders |
| *c | Alignment Marks |
With the No. 1 piston positioned at TDC on the compression stroke, using a feeler gauge, adjust each valve clearance.
| Item | Specified Condition |
|---|---|
| Intake | 0.30 mm (0.0118 in.) |
| Exhaust | 0.45 mm (0.0177 in.) |
| *1 | Adjusting Screw |
| *2 | Feeler Gauge |
| *3 | Lock Nut |
The feeler gauge should move with a very slight pull.
Loosen the lock nut on the valve rocker arm and loosen the adjusting screw.
Insert a 0.30 mm (0.0118 in.) feeler gauge for the intake or a 0.45 mm (0.0177 in.) feeler gauge for the exhaust between the adjusting screw on the valve rocker arm and the valve bridge.
Turn the adjusting screw on the valve rocker arm until the feeler gauge slides with a very slight drag, and lock the adjusting screw with the lock nut.
29 N*m (291 kgf*cm, 21 ft.*lbf)
Recheck the clearance.
Adjust the other valves.
Turn the crankshaft 1 revolution (360°) clockwise.
Adjust the valve clearance for each cylinder in the firing order.
1 - 3 - 4 - 2
(The number of a cylinder is counted from the timing gear side)