Home › Engine / Hybrid System › 14B (ENGINE MECHANICAL) › TIMING GEAR › 2017.01–2019.08
RM2850E _51 Engine / Hybrid System _073170 14B ENGINE MECHANICAL _0356052 TIMING GEAR A

14B ENGINE MECHANICAL  TIMING GEAR  TIMING GEARS AND CAMSHAFT REMOVAL  


PROCEDURE

Hide 1.REMOVE DRIVE BELT(S), FAN, FLUID COUPLING ASSEMBLY (FAN AND FAN SPACER) AND WATER PUMP PULLEY

Hide 23600 3.REMOVE INJECTION NOZZLES (14B, 15B-F, 15B-FT)

Hide 4.REMOVE EXHAUST MANIFOLD HEAT INSULATOR (3B, 14B)

Hide 5.REMOVE TURBOCHARGER AND EXHAUST MANIFOLD ASSEMBLY (15B-FT)

Hide 13901 6.REMOVE VALVE ROCKER SHAFT ASSEMBLY

Hide 7.DISPLACE VALVE LIFTERS

a.
A430592

Remove bolts A, B and gaskets.


b.
A430593

Using a wire, lift up the valve lifter until long hole C of the valve lifter moves up to the position of the installation hole for bolt A.

HINT:

If the lifter is lifted up too high it may get out of position.



c.

Install bolt A.


d.

Check that bolt A prevents the valve lifter from falling.

NOTICE:

Be careful not to scratch the valve lifter.



Hide 8.REMOVE CRANKSHAFT PULLEY

a.
A430594

Using SST, remove the mount bolt.

BU:

SST
09213-58012  (90201-08131, 91111-50845)
09330-00021  

BB:

SST
09213-58012  (90105-08076)
09330-00021  


b.
A430595

Using SST, remove the pulley.

SST
09950-50013  (09951-05010, 09952-05010, 09953-05010, 09953-05020, 09954-05031)


Hide 9.REMOVE RADIATOR PIPE

a.

Remove the 2 bolts holding the radiator pipe to the timing belt cover.


b.

Disconnect the radiator hose from the water pump, and remove the radiator pipe.


Hide 10.REMOVE OIL DIPSTICK AND GUIDE (BB)

Hide 12.REMOVE TIMING GEAR COVER

a.
A430596

Remove the 16 (BU) or 15 (BB) mount bolts and bracket.


b.
A430597

Using a plastic-faced hammer, lightly tap out the gear cover.


c.

Remove the cover gasket.


Hide 13.REMOVE INJECTION PUMP DRIVE GEAR FROM TIMING GEAR COVER

a.

Using a plastic-faced hammer, lightly tap out the gear and remove the drive gear.


Hide 14.CHECK TIMING GEAR BACKLASH

a.
A430598

Align the spline toothless portions of the injection pump drive gear and injection pump, and install the drive gear.


b.
A430599

Using a dial indicator, measure the backlash between each gear.

Standard backlash:

0.058 - 0.162 mm (0.0023 - 0.0064 in.)


Maximum backlash:

0.30 mm (0.0118 in.)


If the backlash is greater than maximum, replace the gears as a set.


c.

Remove the injection pump drive gear.


Hide 15.REMOVE VACUUM PUMP

a.

Remove the 2 bolts and vacuum pump.


b.

Remove the 2 O-rings.


Hide 16.CHECK IDLE GEAR THRUST CLEARANCE

a.
A430600

Using a feeler gauge, measure the idle gear thrust clearance.

Standard thrust clearance:

0.060 - 0.170 mm (0.0024 - 0.0067 in.)


Maximum thrust clearance:

0.30 mm (0.0118 in.)


If the thrust clearance is greater than maximum, replace the thrust plate.


Hide 17.REMOVE IDLE GEAR

a.
A430601

Remove the 2 bolts, thrust plate and idle gear.


Hide 18.REMOVE IDLE GEAR SHAFT

a.
A430602

Remove the union bolt and idle gear shaft.


Hide 19.REMOVE CAMSHAFT TIMING GEAR AND CAMSHAFT ASSEMBLY

a.
A430603

Remove the 2 bolts holding the thrust plate to the cylinder block.


b.
A430604

Carefully pull out the camshaft and timing gear assembly.

NOTICE:

Be careful not to damage the camshaft bearings.



Hide 20.REMOVE CRANKSHAFT TIMING GEAR

a.
A430605

Using SST, remove the timing gear.

SST
09950-50013  (09951-05010, 09952-05010, 09953-05010, 09953-05020, 09954-05031)