Home › Engine / Hybrid System › N04C-UH (ENGINE MECHANICAL) › CAMSHAFT
RM2850E _51 Engine / Hybrid System _073174 N04C-UH ENGINE MECHANICAL _0356073 CAMSHAFT A

N04C-UH ENGINE MECHANICAL  CAMSHAFT  REMOVAL  


PROCEDURE

Hide 16400 1.REMOVE RADIATOR ASSEMBLY

Hide 17201 2.REMOVE TURBOCHARGER SUB-ASSEMBLY

Hide 23670 3.REMOVE INJECTOR ASSEMBLY

Hide 22100 4.REMOVE INJECTION OR SUPPLY PUMP ASSEMBLY

Hide 87208L 6.REMOVE WATER PIPE SUB-ASSEMBLY

Hide 7.REMOVE NO. 2 WATER BY-PASS PIPE SUB-ASSEMBLY

Hide 16206C 8.REMOVE WATER BY-PASS PIPE SUB-ASSEMBLY

Hide 88320 9.SEPARATE COOLER COMPRESSOR ASSEMBLY (w/ Air Conditioning System)

Hide 88431 10.REMOVE NO. 1 COMPRESSOR MOUNTING BRACKET (w/ Air Conditioning System)

Hide 16630G 11.REMOVE IDLER PULLEY ASSEMBLY

Hide 88440B 12.REMOVE IDLE PULLEY ASSEMBLY WITH BRACKET (w/ Air Conditioning System)

Hide 16100 13.REMOVE ENGINE WATER PUMP ASSEMBLY

Hide 27020 14.REMOVE GENERATOR ASSEMBLY

Hide 11301M 15.REMOVE CAMSHAFT POSITION SENSOR

Hide 29601B 16.REMOVE VACUUM PUMP OIL PIPE SUB-ASSEMBLY

Hide 19971E 17.REMOVE VACUUM PIPE

Hide 29300 18.REMOVE VACUUM PUMP ASSEMBLY

Hide 13901 19.REMOVE NO. 1 VALVE ROCKER SHAFT SUB-ASSEMBLY

Hide 11101 22.REMOVE CYLINDER HEAD SUB-ASSEMBLY

Hide 11115 23.REMOVE CYLINDER HEAD GASKET

Hide 13470 25.REMOVE CRANKSHAFT PULLEY ASSEMBLY

a.
A151470

Using a 46 mm socket wrench, remove the nut, spacer and crankshaft pulley.

HINT:

Insert a screwdriver through the inspection hole of the flywheel housing into the ring gear of the flywheel to keep it from turning together with the crankshaft.



Hide 11351H 26.REMOVE FLYWHEEL HOUSING RH STAY

a.

Remove the 4 bolts and the flywheel housing RH stay.


Hide 11351G 27.REMOVE FLYWHEEL HOUSING LH STAY

a.

Remove the 4 bolts and the flywheel housing LH stay.


Hide 12101 28.REMOVE OIL PAN SUB-ASSEMBLY

a.
A000019

Remove the 26 bolts from the oil pan sub-assembly.


b.

Insert the blade of oil pan seal cutter between the cylinder block and oil pan sub-assembly. Cut through the applied sealer and remove the oil pan sub-assembly.

NOTICE:

Do not damage the contact surface of the cylinder block and oil pan sub-assembly.



Hide 12270 29.REMOVE OIL SEPARATOR ASSEMBLY

a.
A258339

Remove the 5 bolts and the oil separator assembly.


b.

Remove the 3 O-rings.


Hide 11321C 30.REMOVE TIMING GEAR CASE

a.
A254645

Remove the 15 bolts.


b.

Using a screwdriver with its tip wrapped in protective tape, pry out the timing gear case.

NOTICE:

Do not damage the contact surfaces of the timing gear case, cylinder block and cylinder head sub-assembly.



Hide 11301C 31.REMOVE TIMING CHAIN OR BELT COVER OIL SEAL

a.
A157078E02
1.016,2.637 1.19,2.802 0.174,0.165 10 *2 1.411,0.438 1.749,0.61 0.338,0.172 10 *1 2.659,1.825 2.798,2.394 2.798,2.394 2.334,2.252 false 1.09,1.367 1.388,0.551 false 0.851,1.539 1.089,2.608 false 2.758,2.431 2.931,2.596 0.174,0.165 10 *3

Using a screwdriver with its tip wrapped in protective tape, pry out the timing chain cover or belt cover oil seal.

Text in Illustration
*1 Protective Tape
*2 Piece of Cloth
*3 Wooden Block

HINT:

Use wooden blocks and a piece of cloth to prevent the contact surfaces and the timing gear case from being damaged.



Hide 13501 32.REMOVE CAMSHAFT

a.
A146589

Remove the 2 bolts and camshaft.