Home › Drivetrain › M15# (MANUAL TRANSMISSION / TRANSAXLE) › MANUAL TRANSMISSION ASSEMBLY (for M156)
RM2850E _52 Drivetrain _073186 M15# MANUAL TRANSMISSION / TRANSAXLE _0356147 MANUAL TRANSMISSION ASSEMBLY(for M156) A

M15# MANUAL TRANSMISSION / TRANSAXLE  MANUAL TRANSMISSION ASSEMBLY(for M156)  REMOVAL  


CAUTION / NOTICE / HINT

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


PROCEDURE

Hide 1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Hide 2.DRAIN MANUAL TRANSMISSION OIL

a.

Remove the drain plug and gasket, and then drain the manual transmission oil.


b.

Install a new gasket and the drain plug.

Torque:

37 N*m (379 kgf*cm, 27 ft.*lbf)



Hide 37110F 3.REMOVE PROPELLER SHAFT WITH CENTER BEARING ASSEMBLY

Hide 17410 4.REMOVE FRONT EXHAUST PIPE ASSEMBLY

a.

for Rear Exhaust Type:

i.

Disconnect the oxygen sensor connector.


ii.
C249238

Remove the 2 nuts, 2 bolts and gasket.


iii.
A156777

Remove the 2 bolts, 2 compression springs and the front exhaust pipe assembly from the exhaust manifold.


iv.

Remove the gasket.



b.

for Side Exhaust Type:

i.
C249238

Remove the 2 nuts, 2 bolts and gasket.


ii.
A156777

Remove the 2 bolts, 2 compression springs and the front exhaust pipe assembly from the exhaust manifold.


iii.

Remove the gasket.



Hide 46501 5.REMOVE PARKING BRAKE DRUM SUB-ASSEMBLY (for Short Wheelbase)

Hide 46501 6.REMOVE PARKING BRAKE DRUM SUB-ASSEMBLY (for Long Wheelbase)

Hide 46503C 7.SEPARATE PARKING BRAKE PLATE SUB-ASSEMBLY

a.
C249239E03
0.188,0.156 0.396,0.333 0.208,0.177 10 false *A 0.188,2.323 0.396,2.51 0.208,0.188 10 false *B

Remove the 4 bolts and separate the parking brake plate sub-assembly from the manual transmission assembly.

Text in Illustration
*A for Short Wheelbase
*B for Long Wheelbase

HINT:

Using a piece of rope, hang the parking brake plate sub-assembly to the vehicle.



Hide 33820B 8.DISCONNECT SHIFT AND SELECT TRANSMISSION CONTROL CABLE

a.
C249218

Remove the 2 nuts and 2 clips, and disconnect the shift and select transmission control cables from the manual transmission assembly.


Hide 31470 9.SEPARATE CLUTCH RELEASE CYLINDER ASSEMBLY

a.
C249223

Remove the 2 bolts and separate the clutch release cylinder assembly.

HINT:

Using a piece of rope, hang the clutch release cylinder assembly to the vehicle.



Hide 28100 10.REMOVE STARTER ASSEMBLY

Hide 11.DISCONNECT CONNECTOR

a.

Disconnect the connectors and wire harness clamps from the manual transmission assembly.


Hide 33110 12.SUPPORT MANUAL TRANSMISSION ASSEMBLY

a.

Support the manual transmission assembly with a transmission jack.


Hide 51204 13.REMOVE NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY

a.
A102004

Remove the 12 bolts and separate the No. 3 frame crossmember sub-assembly from the frame.


b.
A102003

Remove the 4 nuts, 4 washers and the No. 3 frame crossmember sub-assembly from the engine mounting brackets.


Hide 11000 14.SUPPORT PARTIAL ENGINE ASSEMBLY

a.

Support the engine assembly with a transmission jack.

NOTICE:
·

Make sure to support the engine assembly securely to prevent it from tilting when the manual transmission assembly has been removed.

·

Do not tilt the engine assembly and the manual transmission assembly more than necessary.




Hide 33110 15.REMOVE MANUAL TRANSMISSION ASSEMBLY

a.
C249249

Remove the 9 bolts, 2 washers and the No. 1 transmission control cable bracket.


b.

Remove the manual transmission assembly.

NOTICE:
·

To avoid damage to the knock pins, do not pry between the manual transmission assembly and the engine assembly.

·

To avoid damage to the input shaft, do not forcefully shake the manual transmission assembly.




Hide 12325 16.REMOVE NO. 3 ENGINE MOUNTING BRACKET

a.
C249250

Remove the 4 bolts and the No. 3 engine mounting bracket from the manual transmission assembly.


Hide 12321 17.REMOVE NO. 1 ENGINE MOUNTING BRACKET

a.
C249251

Remove the 4 bolts and the No. 1 engine mounting bracket from the manual transmission assembly.


Hide 31230 18.REMOVE CLUTCH RELEASE BEARING ASSEMBLY

a.
C249230

Separate the clutch release fork sub-assembly from the release fork support.


b.

Remove the clutch release bearing assembly with the clutch release fork sub-assembly from the manual transmission assembly.


Hide 31204 19.REMOVE CLUTCH RELEASE FORK SUB-ASSEMBLY

a.

Disengage the release bearing hub clip and remove the clutch release fork sub-assembly from the clutch release bearing assembly.


Hide 31126 20.REMOVE CLUTCH RELEASE FORK BOOT

a.

Remove the clutch release fork boot from the manual transmission assembly.


Hide 31236B 21.REMOVE RELEASE FORK SUPPORT

a.
C249231

Remove the release fork support from the manual transmission assembly.


Hide 31111 22.REMOVE CLUTCH HOUSING

C249232

a.

Remove the 9 bolts and the clutch housing from the manual transmission assembly.