Home › Drivetrain › M15# (MANUAL TRANSMISSION / TRANSAXLE) › MANUAL TRANSMISSION ASSEMBLY (for M156)
RM2850E _52 Drivetrain _073186 M15# MANUAL TRANSMISSION / TRANSAXLE _0356147 MANUAL TRANSMISSION ASSEMBLY(for M156) A

M15# MANUAL TRANSMISSION / TRANSAXLE  MANUAL TRANSMISSION ASSEMBLY(for M156)  INSTALLATION  


PROCEDURE

Hide 31111 1.INSTALL CLUTCH HOUSING

a.

Install the clutch housing to the manual transmission assembly with the 9 bolts.

Torque:

37 N*m (379 kgf*cm, 27 ft.*lbf)



Hide 31236B 2.INSTALL RELEASE FORK SUPPORT

a.

Install the release fork support to the manual transmission assembly.

Torque:

39 N*m (400 kgf*cm, 29 ft.*lbf)



Hide 31126 3.INSTALL CLUTCH RELEASE FORK BOOT

a.

Install the clutch release fork boot to the manual transmission assembly.


Hide 31204 4.INSTALL CLUTCH RELEASE FORK SUB-ASSEMBLY

a.
C128464

Apply release hub grease to the clutch release fork sub-assembly.

Text in Illustration
V100135

Release hub grease

Grease:

Toyota Genuine Release Hub Grease or equivalent



b.

Engage the release bearing hub clip and install the clutch release fork sub-assembly to the clutch release bearing assembly.


Hide 31230 5.INSTALL CLUTCH RELEASE BEARING ASSEMBLY

a.

Install the clutch release bearing assembly with the clutch release fork sub-assembly to the manual transmission assembly.


b.

Install the clutch release fork sub-assembly to the release fork support.

NOTICE:

After installation, move the fork back and forth to check that the release bearing slides smoothly.



c.
C249234

Apply clutch spline grease to the input shaft spline.

Text in Illustration
V100135

Clutch spline grease

Grease:

Toyota Genuine Clutch Spline Grease or equivalent



Hide 12325 6.INSTALL NO. 3 ENGINE MOUNTING BRACKET

a.

Install the No. 3 engine mounting bracket to the manual transmission assembly with the 4 bolts.

Torque:

44 N*m (449 kgf*cm, 32 ft.*lbf)



Hide 12321 7.INSTALL NO. 1 ENGINE MOUNTING BRACKET

a.

Install the No. 1 engine mounting bracket to the manual transmission assembly with the 4 bolts.

Torque:

44 N*m (449 kgf*cm, 32 ft.*lbf)



Hide 33110 8.INSTALL MANUAL TRANSMISSION ASSEMBLY

a.

Support the manual transmission assembly with a transmission jack.


b.

Install the manual transmission assembly.

NOTICE:
·

Be careful not to pinch wire harnesses, etc.

·

Do not forcefully pry on the manual transmission assembly.

·

To avoid damage to the input shaft, do not forcefully shake the manual transmission assembly.

·

Insert knock pins into the knock pin holes securely so that the end face of the manual transmission assembly fits close against the engine assembly before tightening the bolts.




c.
C249249E02
0.625,1.438 0.75,1.594 0.125,0.156 10 false B 0.865,1.906 0.99,2.063 0.125,0.156 10 false B 2.271,1.979 2.396,2.135 0.125,0.156 10 false B 2.635,1.802 2.76,1.958 0.125,0.156 10 false B 1.49,0.031 1.615,0.188 0.125,0.156 10 false A 1.979,0.073 2.104,0.229 0.125,0.156 10 false A 2.75,0.844 2.875,1 0.125,0.156 10 false A 2.708,1.49 2.833,1.646 0.125,0.156 10 false A 0.552,0.99 0.677,1.146 0.125,0.156 10 false A

Install the No. 1 transmission control cable bracket, 2 washers and 9 bolts.

Torque:
Bolt A:

72 N*m (729 kgf*cm, 53 ft.*lbf)

Bolt B:

37 N*m (379 kgf*cm, 27 ft.*lbf)


HINT:

Install the 2 washers between the No. 1 transmission control cable bracket and the clutch housing.



Hide 51204 9.INSTALL NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY

a.

Install the No. 3 frame crossmember sub-assembly to the engine mounting brackets with the 4 nuts and 4 washers.

Torque:

56 N*m (571 kgf*cm, 41 ft.*lbf)



b.

Install the No. 3 frame crossmember sub-assembly to the frame with the 12 bolts.

Torque:

50 N*m (510 kgf*cm, 37 ft.*lbf)



Hide 10.CONNECT CONNECTOR

a.

Connect the connectors and wire harness clamps to the manual transmission assembly.


Hide 28100 11.INSTALL STARTER ASSEMBLY

Hide 31470 12.INSTALL CLUTCH RELEASE CYLINDER ASSEMBLY

a.

Install the clutch release cylinder assembly with the 2 bolts.

Torque:

12 N*m (120 kgf*cm, 9 ft.*lbf)



Hide 33820B 13.CONNECT SHIFT AND SELECT TRANSMISSION CONTROL CABLE

a.

Connect the shift and select transmission control cables to the manual transmission assembly with the 2 nuts and 2 new clips.

Torque:

15 N*m (153 kgf*cm, 11 ft.*lbf)



Hide 46503C 14.INSTALL PARKING BRAKE PLATE SUB-ASSEMBLY

a.

Clean the 4 bolts and their holes.


b.
A057108E73
2.188,0.229 1.948,1.094 false 2.271,0.094 2.521,0.302 0.25,0.208 12 false *1

Apply adhesive to 2 or 3 threads on the end of the 4 bolts.

Text in Illustration
*1 Adhesive

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



c.

Install the parking brake plate sub-assembly to the manual transmission assembly with the 4 bolts.

Torque:

47 N*m (474 kgf*cm, 34 ft.*lbf)



Hide 46501 15.INSTALL PARKING BRAKE DRUM SUB-ASSEMBLY (for Short Wheelbase)

Hide 46501 16.INSTALL PARKING BRAKE DRUM SUB-ASSEMBLY (for Long Wheelbase)

Hide 17410 17.INSTALL FRONT EXHAUST PIPE ASSEMBLY

a.

for Rear Exhaust Type:

i.

Install a new gasket.


ii.

Install the front exhaust pipe assembly to the exhaust manifold with the 2 bolts and 2 compression springs.

Torque:

43 N*m (438 kgf*cm, 32 ft.*lbf)



iii.

Install the 2 bolts, 2 new nuts and a new gasket.

Torque:

43 N*m (438 kgf*cm, 32 ft.*lbf)



iv.

Connect the oxygen sensor connector.



b.

for Side Exhaust Type:

i.

Install a new gasket.


ii.

Install the front exhaust pipe assembly to the exhaust manifold with the 2 bolts and 2 compression springs.

Torque:

43 N*m (438 kgf*cm, 32 ft.*lbf)



iii.

Install the 2 bolts, 2 new nuts and a new gasket.

Torque:

43 N*m (438 kgf*cm, 32 ft.*lbf)




Hide 37110F 18.INSTALL PROPELLER SHAFT WITH CENTER BEARING ASSEMBLY

Hide 19.ADD MANUAL TRANSMISSION OIL

a.

Park the vehicle in a level place.


b.

Remove the filler plug and gasket.


c.

Add manual transmission oil.

Oil grade:

API GL-4


Viscosity:

SAE 75W-90


Capacity (Reference):

3.2 liters (3.4 US qts, 2.8 Imp. qts)



d.
D025304E96
0.667,1.354 0.854,1.573 0.188,0.219 10 false *a

Check that the oil surface is within 5 mm (0.197 in.) below the lowest point of the filler plug opening.

Text in Illustration
*a 0 to 5 mm (0 to 0.197 in.)

NOTICE:
·

Problems may occur when the oil level is too high or too low.

·

After replacing the oil, drive the vehicle and check the oil level again.




e.

Install a new gasket and the filler plug.

Torque:

37 N*m (379 kgf*cm, 27 ft.*lbf)



Hide 20.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:

3.9 N*m (40 kgf*cm, 35 in.*lbf)


Hide 21.INSPECT FOR MANUAL TRANSMISSION OIL LEAK

Hide 22.INSPECT FOR EXHAUST GAS LEAK