Home › Vehicle Interior › SEAT › REAR SEAT ASSEMBLY (for Single-Passenger Seat with 3 Point Type Seat Belt)
RM2850E _58 Vehicle Interior _073189 SEAT _0356166 REAR SEAT ASSEMBLY(for Single-Passenger Seat with 3 Point Type Seat Belt) A

SEAT  REAR SEAT ASSEMBLY(for Single-Passenger Seat with 3 Point Type Seat Belt)  REASSEMBLY  


CAUTION / NOTICE / HINT

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.


HINT:
·

The procedure listed below is for 2nd row to 7th row for long body, and 2nd row to 6th row for standard body.

·

The procedure listed below is a representative example.

·

Use the same procedure for all rows, unless otherwise specified.



PROCEDURE

Hide 79290A 1.INSTALL NO. 2 SEATBACK SPRING ASSEMBLY LH

a.
B466240E01
0.167,1.948 0.458,1.344 true 0.49,2.063 0.781,1.458 true 3.24,2.031 2.958,1.396 true 2.917,2.135 2.635,1.5 true 0.042,1.958 0.354,2.156 0.313,0.198 10 false *a 3.229,2.073 3.417,2.26 0.188,0.188 10 false *a 2.906,2.188 3.094,2.375 0.188,0.188 10 false *b 0.396,2.094 0.583,2.281 0.188,0.188 10 false *b

Attach the 2 guides and temporarily install the No. 2 seatback spring assembly LH using the 4 bolts.

Text in Illustration
*a Bolt A
*b Bolt B

HINT:

Use bolt B as the installation bolt for the floor anchors of the rear No. 2 seat inner belt assembly and rear seat outer belt assembly.



b.

While pushing the No. 2 seatback spring assembly LH forward, tighten the 2 bolts labeled A.

Torque:

42 N*m (428 kgf*cm, 31 ft.*lbf)



c.

Remove the 2 bolts labeled B.


Hide 71875G 2.INSTALL SEAT RECLINING ADJUSTER INSIDE COVER LH (w/ Reclining Function)

a.
B466384

Attach the 4 guides to install the reclining adjuster inside cover LH.


b.

Install the clip.


Hide 72345A 3.INSTALL RECLINING CONNECTING PIPE

a.
B398774

Install the reclining connecting pipe.


Hide 79968 4.INSTALL REAR NO. 5 SEAT LEG SIDE COVER (for 2nd Row Seat)

a.
B466238

Slide the rear No. 5 seat leg side cover in the direction indicated by the arrow shown in the illustration and attach the 2 hooks to install it.


Hide 79967B 5.INSTALL REAR NO. 2 SEAT LEG SIDE COVER (for 2nd Row Seat)

a.
B466236

Slide the rear No. 2 seat leg side cover in the direction indicated by the arrow shown in the illustration and install it.


Hide 79967K 6.INSTALL REAR NO. 4 SEAT LEG SIDE COVER (for 2nd Row Seat)

a.
B466234

Attach the 3 claws to install the rear No. 4 seat leg side cover.


Hide 71867M 7.INSTALL REAR NO. 1 SEAT INNER CUSHION SHIELD RH

a.
B466383

Install the rear No. 1 seat inner cushion shield RH with the screw.


Hide 71868C 8.INSTALL REAR NO. 1 SEAT INNER CUSHION SHIELD LH

a.
B457752

Install the rear No. 1 seat inner cushion shield LH with the screw.


Hide 79012 9.INSTALL NO. 1 SEAT CUSHION COVER SUB-ASSEMBLY LH

HINT:
·

When installing the seat cover, refer to the precautions in order to prevent wrinkles from forming.

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY>PRECAUTION

·

Align the seam allowance in a single direction as shown in the illustration.

B466427E01
0.677,0.5 0.823,0.667 0.146,0.167 10 true A 0.885,0.552 1.031,0.719 0.146,0.167 10 true A 1.938,0.781 2.083,0.948 0.146,0.167 10 true B 2.104,0.833 2.25,1 0.146,0.167 10 true B 3.771,0.188 4.229,0.385 0.458,0.198 10 false A-A 5.573,0.208 6.031,0.406 0.458,0.198 10 false B-B



a.

Set the No. 1 seat cushion cover sub-assembly LH in place.


b.
B398790E01
0.594,3.167 0.375,3.76 true 1.792,3.76 2.271,2.729 2.271,2.729 2.531,2.729 true 1.51,0.844 1.708,0.979 0.198,0.135 10 true (1) 2.01,0.917 2.208,1.063 0.198,0.146 10 true (2) 0.979,0.813 1.177,0.948 0.198,0.135 10 true (3) 0.698,1.146 0.875,1.281 0.177,0.135 10 true (4) 2.458,1.177 2.635,1.323 0.177,0.146 10 true (5) 2.271,1.396 2.448,1.542 0.177,0.146 10 true (6) 0.292,3.813 0.458,3.979 0.167,0.167 10 false *a 2.583,2.625 2.75,2.792 0.167,0.167 10 false *b

Using hog ring pliers, install the No. 1 seat cushion cover sub-assembly LH to the No. 1 seat cushion pad sub-assembly LH with 6 new hog rings in the order shown in the illustration.

Text in Illustration
*a Cutout
*b Hog Ring Pliers

NOTICE:
·

Do not dirty or damage the No. 1 seat cushion cover sub-assembly LH.

·

Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the No. 1 seat cushion cover sub-assembly LH.



HINT:

Install the hog rings at the cutouts if they are there.



c.
B466231E01
2.615,1.292 2.615,1.677 true 1.135,2.188 0.885,2.333 true 2.219,2.188 2.531,2.323 true 2.542,1.719 2.76,1.896 0.219,0.177 10 false *a 2.042,2.094 2.26,2.271 0.219,0.177 10 false *a 1.167,2.083 1.385,2.26 0.219,0.177 10 false *a

for Type A:

i.

Attach the 3 pieces of fastening tape to install the strap of the No. 1 seat cushion cover sub-assembly LH as shown in the illustration.

Text in Illustration
*a Alignment Hole
V100145

Fastening Tape



d.
B466485E01
2.333,1.823 2.333,1.396 true 2.271,1.854 2.583,2.052 0.313,0.198 10 false *a

for Type B:

i.

Attach the pieces of fastening tape to install the strap of the No. 1 seat cushion cover sub-assembly LH as shown in the illustration.

Text in Illustration
*a Alignment Hole
V100145

Fastening Tape



e.

Set the No. 1 seat cushion cover sub-assembly LH with pad on the No. 1 seat leg sub-assembly LH.


f.
B466228

for Long Body 5th Row Seat:

for Standard Body 4th Row Seat:

i.

Pass the strap of the No. 1 seat cushion cover sub-assembly LH through the No. 1 seat leg sub-assembly LH.



g.
B466227E01
1.385,0.552 1.563,0.635 true 1.698,0.708 1.844,0.969 true 1.708,3.802 1.708,4.094 true 2.646,3.875 2.646,4.063 true 0.781,3.875 0.781,4.063 true 1.229,0.458 1.448,0.667 0.219,0.208 10 false *a 1.813,1 2.031,1.177 0.219,0.177 10 false *b 0.677,4.094 0.896,4.271 0.219,0.177 10 false *c 2.552,4.094 2.771,4.271 0.219,0.177 10 false *c 1.604,4.125 1.823,4.302 0.219,0.177 10 false *1

for Type A:

i.

Attach the 5 hooks to install the No. 1 seat cushion cover LH with pad to the No. 1 seat leg sub-assembly LH as shown in the illustration.

Text in Illustration
*1 No. 1 Seat Leg Sub-assembly LH
*a Frame Hole
*b Pad Hole
*c Hook



h.

for Type B:

i.

Attach the 6 hooks to install the No. 1 seat cushion cover LH with pad to the No. 1 seat leg sub-assembly LH as shown in the illustration.

B472792E01
2.094,0.177 2.833,0.333 true 2.854,0.417 3.229,0.5 true 2.26,2.448 2.365,2.125 2.365,2.125 2.49,2.125 true 2.979,2.479 3.083,2.156 3.083,2.156 3.208,2.156 true 3.656,2.448 3.76,2.125 3.76,2.125 3.885,2.125 true 1.906,0.073 2.219,0.271 0.313,0.198 10 false *a 3.281,0.448 3.594,0.646 0.313,0.198 10 false *b 2.542,2.031 2.854,2.229 0.313,0.198 10 false *c 3.229,2.073 3.542,2.271 0.313,0.198 10 false *1 3.917,2.042 4.229,2.24 0.313,0.198 10 false *c

Text in Illustration
*1 No. 1 Seat Leg Sub-assembly LH - -
*a Frame Hole *b Pad Hole
*c Hook - -



i.
B466225

Attach the fastening tape and close the No. 1 seat cushion cover sub-assembly LH.

Text in Illustration
V100145

Fastening Tape


Hide 73343 10.INSTALL REAR SEAT SHOULDER BELT GUIDE RH

a.
B466381

Attach the guide to install the rear seat shoulder belt guide RH.


b.

Install the 2 screws.


Hide 79018A 11.INSTALL NO. 1 SEATBACK PAD SUB-ASSEMBLY LH

a.
B466380

Install the No. 1 rear seatback pad sub-assembly LH.


Hide 79014 12.INSTALL NO. 1 SEATBACK COVER SUB-ASSEMBLY LH

HINT:
·

When installing the seat cover, refer to the precautions in order to prevent wrinkles from forming.

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY>PRECAUTION

·

Align the seam allowance in a single direction as shown in the illustration.

B466425E01
2.823,0.188 3.281,0.385 0.458,0.198 10 false A-A 4.313,0.177 4.771,0.375 0.458,0.198 10 false B-B 6.073,0.208 6.531,0.406 0.458,0.198 10 false C-C 0.656,0.427 0.802,0.594 0.146,0.167 10 true A 0.802,0.458 0.948,0.625 0.146,0.167 10 true A 1.01,0.021 1.156,0.188 0.146,0.167 10 true C 0.885,0.167 1.031,0.333 0.146,0.167 10 true C 1.417,0.583 1.563,0.75 0.146,0.167 10 true B 1.563,0.625 1.708,0.792 0.146,0.167 10 true B



a.

Set the No. 1 seatback cover sub-assembly LH.


b.
B466385E01
1.917,3.823 2.25,3 2.25,3 2.458,3 true 0.458,2.583 0.844,2.865 true 2.292,1.604 2.49,1.781 0.198,0.177 10 false (2) 1.635,1.698 1.833,1.875 0.198,0.177 10 false (1) 0.292,2.458 0.49,2.635 0.198,0.177 10 false *a 2.49,2.896 2.688,3.073 0.198,0.177 10 false *b

Using hog ring pliers, install the 2 new hog rings in the order shown in the illustration.

Text in Illustration
*a Cutout
*b Hog Ring Pliers

NOTICE:
·

Do not dirty or damage the No. 1 seatback cover sub-assembly LH.

·

Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the No. 1 seatback cover sub-assembly LH.



HINT:

Install the hog rings at the cutouts if they are there.



c.
B466386E01
1.854,3.823 2.219,2.833 2.219,2.833 2.51,2.833 true 0.844,2.865 0.5,2.417 true 1.635,2.135 1.802,2.292 0.167,0.156 10 false (1) 2.24,2.031 2.406,2.188 0.167,0.156 10 false (2) 0.375,2.26 0.542,2.417 0.167,0.156 10 false *a 2.594,2.74 2.76,2.896 0.167,0.156 10 false *b

Using hog ring pliers, install the 2 new hog rings in the order shown in the illustration.

Text in Illustration
*a Cutout
*b Hog Ring Pliers

NOTICE:
·

Do not dirty or damage the No. 1 seatback cover sub-assembly LH.

·

Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the No. 1 seatback cover sub-assembly LH.



HINT:

Install the hog rings at the cutouts if they are there.



d.
B466387E01
1.625,3.75 1.979,2.719 1.979,2.719 2.323,2.719 true 0.656,3.146 0.354,3.781 true 0.281,3.813 0.5,4.01 0.219,0.198 10 false *a 2.385,2.615 2.604,2.813 0.219,0.198 10 false *b

w/ Seatback Board:

i.

Using hog ring pliers, install the No. 1 seatback cover sub-assembly LH with 3 new hog rings.

Text in Illustration
*a Cutout
*b Hog Ring Pliers

NOTICE:
·

Do not dirty or damage the No. 1 seatback cover sub-assembly LH.

·

Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the No. 1 seatback cover sub-assembly LH.



HINT:

Install the hog rings at the cutouts if they are there.




Hide 13.INSTALL REAR SEAT SHOULDER BELT COVER LH

a.
B466430

Attach the guide and claw to install the rear seat shoulder belt cover LH.


b.

Install the clip.


Hide 73302 15.INSTALL REAR SEAT OUTER BELT SUB-ASSEMBLY (for 2nd Row Seat)

HINT:

Use the same procedure as for the rear seat outer belt assembly floor anchor.


Hide 73375 16.INSTALL REAR SEAT SHOULDER BELT COVER LH

a.
B466375E01
1.604,0.885 1.719,0.885 1.719,0.885 1.875,1.094 false 1.427,0.792 1.74,0.99 0.313,0.198 10 false *a

Install the rear seat outer belt assembly through the gap in the rear seat shoulder belt cover LH.

Text in Illustration
*a Gap


b.
B466388

Slide the part in the direction indicated by the arrow shown in the illustration to attach the 2 clamps.


c.
B466389

Slide the part as shown in the illustration, attach the claw and guide and install the rear seat shoulder belt cover LH.


Hide 73136A 17.INSTALL SHOULDER BELT ANCHOR COVER LH

a.
B466372E01
1.792,0.896 1.979,0.698 true 2.031,0.583 2.344,0.781 0.313,0.198 10 false *a

Install the rear seat outer belt assembly through the gap in the shoulder belt anchor cover LH.

Text in Illustration
*a Gap


b.
B466371

Install the shoulder belt anchor cover LH with the 2 screws.


Hide 73373F 18.INSTALL REAR SEAT SHOULDER BELT HOLE COVER (w/o Seatback Board)

a.
B457782

Attach the 10 claws and 8 guides to install the rear seat shoulder belt hole cover.


b.
B457780

Close the fastener.


c.

Insert the end of the fastener inside the seat cover material as shown in the illustration.

B457779


d.
B457777E01
0.385,2.76 0.552,2.906 true 2.219,2.833 1.979,2.833 1.979,2.833 1.604,3.771 true 0.24,2.646 0.438,2.813 0.198,0.167 10 false *a 2.281,2.729 2.521,2.927 0.24,0.198 10 false *b

Using hog ring pliers, install the No. 1 seatback cover sub-assembly LH with 3 new hog rings.

Text in Illustration
*a Cutout
*b Hog Ring Pliers

NOTICE:
·

Do not dirty or damage the No. 1 seatback cover sub-assembly LH.

·

Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the No. 1 seatback cover sub-assembly LH.



HINT:

Install the hog rings at the cutouts if they are there.



Hide 19.CONNECT REAR SEAT OUTER BELT ASSEMBLY FLOOR ANCHOR (except 2nd Row Seat)

a.

Check that the rear seat outer belt assembly is not twisted.


b.
B466390E01
1.802,1.333 1.99,1.188 true 0.573,1.625 1.313,1.677 true 1.979,1.063 2.177,1.25 0.198,0.188 10 false *a 0.406,1.531 0.604,1.719 0.198,0.188 10 false *a

Install the floor anchor of the rear seat outer belt assembly with the bolt.

Torque:

42 N*m (428 kgf*cm, 31 ft.*lbf)


NOTICE:

The rear seat outer belt assembly must not overlap the location.


Text in Illustration
*a Location


Hide 20.CONNECT REAR SEAT OUTER BELT SUB-ASSEMBLY FLOOR ANCHOR (for 2nd Row Seat)

HINT:

Use the same procedure as for the rear seat outer belt assembly floor anchor.


Hide 73344 21.INSTALL REAR SEAT SHOULDER BELT GUIDE LH

a.
B466405E01
1.719,1.771 1.719,1.188 true 1.635,1.823 1.833,2 0.198,0.177 10 true *a

Install the rear seat outer belt assembly through the gap in the rear seat shoulder belt guide LH.

Text in Illustration
*a Gap


b.
B466391

Slide the part in the direction indicated by the arrow shown in the illustration and attach the 2 guides.


c.

Attach the 2 claws to install the rear seat shoulder belt guide LH.


Hide 73179A 22.INSTALL SEAT BELT ANCHOR COVER CAP LH

a.
B466392

Attach the 3 guides and 2 claws to install the seat belt anchor cover cap LH.


Hide 79209 23.INSTALL NO. 2 SEATBACK BOARD SUB-ASSEMBLY (w/ Seatback Board)

a.
B466457

Slide the part in the direction indicated by the arrow shown in the illustration and attach the 3 guides to install the No. 2 seatback board sub-assembly.


Hide 74610A 24.INSTALL ASSIST GRIP SUB-ASSEMBLY (w/ Assist Grip)

a.
B398693

Install the assist grip sub-assembly with 2 new screws.


Hide 74617C 25.INSTALL ASSIST GRIP PLUG (w/ Assist Grip)

HINT:

Use the same procedure for the other assist grip plugs.


a.
B398728

Attach the 2 claws to install the assist grip plug.


Hide 71149K 26.INSTALL REAR SEAT INNER LEG COVER

a.

Attach the 2 claws and 2 guides to install the rear seat inner leg cover.

B466472E01
0.156,0.083 0.531,0.323 0.375,0.24 12 false *A 3.74,0.083 4.115,0.323 0.375,0.24 12 false *B

Text in Illustration
*A except 3rd Row Seat *B for Standard Body 5th Row Seat


b.
B466221

for 3rd Row Seat:

i.

Attach the claw and 2 guides to install the rear seat inner leg cover.



c.

Install the screw.

B466471E01
0.031,0.031 0.406,0.271 0.375,0.24 12 false *A 2.458,0.052 2.833,0.292 0.375,0.24 12 false *B 4.958,0.031 5.333,0.271 0.375,0.24 12 false *C

Text in Illustration
*A for 3rd Row Seat *B except 3rd Row Seat
*C for Standard Body 5th Row Seat - -


Hide 71148N 27.INSTALL REAR SEAT OUTER LEG COVER

a.

except 3rd Row Seat:

i.

Attach the 9 claws, 2 guides and 4 clips to install the rear seat outer leg cover.

B466215



b.

for 3rd Row Seat:

i.

Attach the 10 claws, guide and 2 clips to install the rear seat outer leg cover.

B466481



c.

Install the 3 screws in the order shown in the illustration.

B466479E02
0.354,0.063 0.729,0.302 0.375,0.24 12 false *A 3.906,0.063 4.281,0.302 0.375,0.24 12 false *B 1.333,1.448 1.792,1.646 0.458,0.198 10 false (1) 3.313,1.448 3.771,1.646 0.458,0.198 10 false (2) 6.021,1.583 6.479,1.781 0.458,0.198 10 false (3) 4.802,1.385 5.26,1.583 0.458,0.198 10 false (1) 6.542,1.5 7,1.698 0.458,0.198 10 false (2) 2.615,1.583 3.073,1.781 0.458,0.198 10 false (3)

Text in Illustration
*A except 3rd Row Seat *B for 3rd Row Seat


Hide 72379 28.INSTALL SEAT RECLINING HANDLE BELT (w/ Reclining Function)

a.

Install the seat reclining handle belt to the No. 2 seatback spring assembly LH.

B466396


Hide 73306 30.INSTALL SEAT INNER BELT SUB-ASSEMBLY (for 2nd Row Seat)

HINT:

Use the same procedure as for the rear seat inner belt assembly.


Hide 71812K 31.INSTALL RECLINING ADJUSTER COVER LH

a.
B466397

w/ Reclining Function:

i.

Pass the seat reclining handle belt through the hole in the reclining adjuster cover LH.



b.
B466468

for Type A:

i.

Attach the 7 claws and 3 guides to install the reclining adjuster cover LH.



c.
B466470

for Type B:

i.

Attach the 7 claws and 2 guides to install the reclining adjuster cover LH.



d.

for Type C:

i.

Attach the 6 claws and 2 guides to install the reclining adjuster cover LH.

B466212



e.
B466483

Install the 2 screws.


Hide 71876E 32.INSTALL RECLINING ADJUSTER INSIDE COVER LH

a.

for 2nd and 7th Row Seat:

i.

Attach the 7 claws and 2 guides to install the reclining adjuster inside cover LH.

B457825



b.
B466466

except 2nd and 7th Row Seat:

i.

w/ Reclining Function:

Attach the 6 claws and 2 guides to install the reclining adjuster inside cover LH.


ii.
B466489

w/o Reclining Function:

Attach the 7 claws and 2 guides to install the reclining adjuster inside cover LH.



c.
B466482

Install the 2 screws.