Wear protective gloves. Sharp areas on the parts may injure your hands.
Use the same procedure for RHD and LHD vehicles.
The procedures listed below are for RHD vehicles.
The procedure listed below is for 1st row to 7th row for long body, and 2nd row to 6th row for standard body.
2nd row seats are not installed to vehicles with cooling boxes
The procedure listed below is a representative example.
Use the same procedure for all rows, unless otherwise specified.
73370B
1.INSTALL REAR SEAT OUTER BELT ASSEMBLY (except 2nd Row Seat)
Attach the 2 guides.
Install the rear seat outer belt assembly with the bolt.
42 N*m (428 kgf*cm, 21 ft.*lbf)
Check that the rear seat outer belt assembly is not twisted.
Pass the rear seat outer belt assembly through the No. 1 seatback spring assembly LH as shown in the illustration.
Check that the rear seat outer belt assembly is not twisted.
Pass the rear seat outer belt assembly through the hole in the No. 1 seatback cover sub-assembly LH as shown in the illustration.
73302
2.INSTALL REAR SEAT OUTER BELT SUB-ASSEMBLY (for 2nd Row Seat)
Attach the 2 guides.
Install the rear seat outer belt sub-assembly with the bolt.
42 N*m (428 kgf*cm, 21 ft.*lbf)
Check that the rear seat outer belt sub-assembly is not twisted.
Pass the rear seat outer belt sub-assembly through the No. 1 seatback cover sub-assembly LH and No. 1 seatback spring assembly LH as shown in the illustration.
Check that the rear seat outer belt sub-assembly is not twisted.
Pass the rear seat outer belt sub-assembly through the hole in the No. 1 seatback cover sub-assembly LH as shown in the illustration.
73375B
3.INSTALL REAR SEAT SHOULDER BELT HOLE COVER LH
73136A
4.INSTALL SHOULDER BELT ANCHOR COVER LH
73373F
5.INSTALL REAR SEAT SHOULDER BELT HOLE COVER (w/o Seatback Board)
6.CONNECT REAR SEAT OUTER BELT ASSEMBLY FLOOR ANCHOR (except 2nd Row Seat)
Check that the rear seat outer belt assembly is not twisted.
Connect the floor anchor of the rear seat outer belt assembly with the bolt.
42 N*m (428 kgf*cm, 21 ft.*lbf)
| *a | Location |
The rear seat outer belt assembly must not overlap the location.
7.CONNECT REAR SEAT OUTER BELT SUB-ASSEMBLY FLOOR ANCHOR (for 2nd Row Seat)
Use the same procedure as for the rear seat outer belt assembly floor anchor.
73344
8.INSTALL REAR SEAT SHOULDER BELT GUIDE LH
73179A
9.INSTALL SEAT BELT ANCHOR COVER CAP LH
79209
10.INSTALL NO. 2 SEAT BACK BOARD SUB-ASSEMBLY (w/ Seatback Board)
74610A
11.INSTALL ASSIST GRIP SUB-ASSEMBLY (w/ Assist Grip)
74617C
12.INSTALL ASSIST GRIP PLUG (w/ Assist Grip)
71812K
13.INSTALL RECLINING ADJUSTER COVER LH (except 2nd Row Seat)
71876E
14.INSTALL RECLINING ADJUSTER INSIDE COVER LH (for 2nd Row Seat)
73220
15.INSTALL FRONT SEAT OUTER BELT ASSEMBLY LH (for 1st Row Seat)
Attach the 2 guides and temporarily install the front seat outer belt assembly LH.
Install the 2 bolts.
5.0 N*m (51 kgf*cm, 44 in.*lbf)
42 N*m (428 kgf*cm, 31 ft.*lbf)
| *a | Bolt A |
| *b | Bolt B |
w/ Pretensioner and Force Limiter:
Connect the pretensioner connector and lock the locking button as shown in the illustration.
Securely lock the locking button.
| *a | Locking Button |
Check that the front seat outer belt assembly is not twisted.
Connect the shoulder anchor of the front seat outer belt assembly LH with the bolt.
42 N*m (428 kgf*cm, 21 ft.*lbf)
Attach the 2 claws to close the shoulder anchor cover.
Check that the front seat outer belt assembly is not twisted.
Attach the guide to connect the floor anchor of the front seat outer belt assembly LH with the bolt.
42 N*m (428 kgf*cm, 21 ft.*lbf)
73224
16.INSTALL FRONT SEAT BELT RETRACTOR COVER LH (for 1st Row Seat)
Install the front seat outer belt assembly LH through the gap in the front seat belt retractor cover LH.
Attach the 2 clips to install the front seat belt retractor cover LH.
17.INSTALL REAR NO. 1 SEAT ASSEMBLY LH
for 1st Row Seat:
except 1st Row Seat:
18.INSTALL COOLING BOX (w/ Cool Box)
19.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL (for 1st Row Seat, w/ Pretensioner and Force Limiter)
20.CHECK SRS WARNING LIGHT (for 1st Row Seat, w/ Pretensioner and Force Limiter)
for 2 connectors Type:
for 3 connectors Type: