Home › Vehicle Exterior › WINDOW / GLASS › FRONT SIDE FIX WINDOW ASSEMBLY LH (for Lower Side)
RM2850E _59 Vehicle Exterior _073195 WINDOW / GLASS _0356212 FRONT SIDE FIX WINDOW ASSEMBLY LH(for Lower Side) A

WINDOW / GLASS  FRONT SIDE FIX WINDOW ASSEMBLY LH(for Lower Side)  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for RHD vehicles.



PROCEDURE

Hide 62109A 1.CLEAN LOWER SIDE WINDOW GLASS SUB-ASSEMBLY LH

a.
E268586

Clean the outer edge of the lower side window glass sub-assembly LH with non-residue solvent.

NOTICE:
·

Do not touch the lower side window glass sub-assembly LH surface after cleaning it.

·

Do not damage the glass.

·

Even if using a new lower side window glass sub-assembly LH, clean the lower side window glass sub-assembly with non-residue solvent.




Hide 68217A 2.INSTALL NO. 1 SIDE WINDOW PIN

a.

Using non-residue solvent, clean the No. 1 side window pin installation surface of the lower side window glass sub-assembly LH.


b.

Install the glass primer to the No. 1 side window pin installation surface of the lower side window glass sub-assembly LH.

NOTICE:
·

Do not apply too much primer.

·

Allow the primer to dry for 3 minutes or more.




c.

Remove the peeling paper from a new No. 1 side window pin.

HINT:

After removing the peeling paper, keep the exposed adhesive free from foreign matter.



d.

Install the 3 No. 1 side window pins to the lower side window glass sub-assembly LH as shown in the illustration.

B471166E01
1.302,0.979 1.625,0.594 1.625,0.594 1.396,1.042 true 5.396,0.417 5.958,0.26 5.958,0.26 5.552,0.604 true 1.177,1.198 1.042,1.635 1.042,1.635 1.292,1.25 true 5.354,2.177 5.052,2.542 5.052,2.542 5.594,2.26 true 5.438,2.01 5.938,1.74 5.938,1.74 5.646,2.115 true 5.302,0.802 5.104,1.167 5.104,1.167 5.5,0.844 true 0.146,0.104 0.458,0.302 0.313,0.198 10 false *a 1.552,0.427 1.771,0.625 0.219,0.198 10 false *b 0.844,1.625 1.073,1.823 0.229,0.198 10 false *b 6.031,0.188 6.25,0.375 0.219,0.188 10 false *b 5.021,1.208 5.25,1.396 0.229,0.188 10 false *b 5.99,1.646 6.229,1.833 0.24,0.188 10 false *b 4.854,2.479 5.083,2.667 0.229,0.188 10 false *b

Text in Illustration
*a Back Side *b Ceramic Notch


Hide 62179 3.INSTALL LOWER SIDE WINDOW DAM

a.

Using non-residue solvent, clean the lower side window dam installation surface of the lower side window glass sub-assembly LH.


b.

Install the glass primer to the lower side window dam installation surface of the lower side window glass sub-assembly LH.

NOTICE:
·

Do not apply too much primer.

·

Allow the primer to dry for 3 minutes or more.




c.

Remove the peeling paper from a new windshield glass retainer.

HINT:

After removing the peeling paper, keep the exposed adhesive free from foreign matter.



d.

Install the 6 windshield glass retainers to the lower side window glass sub-assembly LH as shown in the illustration.

B471158N01
1.625,0.635 1.719,0.792 1.719,0.792 1.552,0.708 true 2.583,0.458 2.583,0.333 2.583,0.333 2.479,0.438 true 4.365,0.469 4.281,0.594 4.281,0.594 4.25,0.479 true 5.448,2.313 5.563,2.281 5.563,2.281 5.458,2.208 true 3.177,2.323 3.188,2.469 3.188,2.469 3.281,2.354 true 2.313,1.844 2.302,1.958 2.302,1.958 2.406,1.885 true 1.615,0.813 1.823,0.99 0.208,0.177 10 false *b 2.531,0.167 2.74,0.344 0.208,0.177 10 true *b 4.229,0.604 4.438,0.781 0.208,0.177 10 true *b 5.604,2.208 5.813,2.385 0.208,0.177 10 true *b 3.104,2.469 3.313,2.625 0.208,0.156 10 true *b 2.146,1.958 2.354,2.135 0.208,0.177 10 true *b 0.125,0.125 0.344,0.302 0.219,0.177 10 false *a

Text in Illustration
*a Back Side *b Ceramic Notch


Hide 62109A 4.INSTALL LOWER SIDE WINDOW GLASS SUB-ASSEMBLY LH

a.
B455055E02
0.583,1.177 0.583,1.448 false 0.5,1.479 0.813,1.677 0.313,0.198 10 false *a 3.302,0.625 3.417,0.885 0.115,0.26 10 false a

Clean and shape the contact surface of the vehicle body.

i.

On the contact surface of the vehicle body, use a knife to cut away excess adhesive as shown in the illustration.

Standard:
Area Specified Condition
a 1.0 mm (0.0394 in.) to 3.0 mm (0.118 in.)



ii.

Clean the contact surface of the vehicle body with non-residue solvent.

Text in Illustration
*a Vehicle Body
V100155

Adhesive



b.

Position the lower side window glass sub-assembly LH.

i.

Using suction cups, place the lower side window glass sub-assembly LH in the correct position.


ii.

Check that the entire contact surface of the glass rim is perfectly even.


iii.

Using suction cups, remove the lower side window glass sub-assembly LH.


iv.

Using a brush or sponge, apply body primer to the exposed part of the vehicle body.

NOTICE:
·

Do not apply too much primer.

·

Do not apply primer to the adhesive.

·

When applying the primer, take care of the seams of the panel and spot welds.




v.

Using a brush or sponge, apply glass primer to the contact surface of the glass.

NOTICE:
·

Do not apply too much primer.

·

Allow the primer to dry for 3 minutes or more.



B471163N01
1.25,1.302 1.406,1.5 0.156,0.198 10 false A 1.25,1.688 1.406,1.885 0.156,0.198 10 false A 1.427,1.865 1.583,2.063 0.156,0.198 10 false C 1.271,2.25 1.427,2.448 0.156,0.198 10 false C 2.708,1.469 2.865,1.625 0.156,0.156 10 true B 3.094,1.417 3.25,1.615 0.156,0.198 10 false B 0.156,0.125 0.458,0.333 0.302,0.208 10 false *a 3.896,0.281 4.198,0.49 0.302,0.208 10 false A-A 5.625,0.292 5.927,0.5 0.302,0.208 10 false B-B 3.885,2.083 4.188,2.292 0.302,0.208 10 false C-C 4.5,0.875 4.656,1.073 0.156,0.198 10 false a 4.76,0.521 4.917,0.719 0.156,0.198 10 false b 6.198,0.896 6.354,1.094 0.156,0.198 10 false a 6.479,0.51 6.635,0.708 0.156,0.198 10 false c 4.969,2.208 5.125,2.406 0.156,0.198 10 false c 4.396,2.573 4.552,2.771 0.156,0.198 10 false d

Text in Illustration
*a Back Side - -
V100155

Glass Glass Primer Application Area - -

Standard:
Area Specified Condition
a 14.0 mm (0.551 in.)
b 8.0 mm (0.315 in.)
c 6.0 mm (0.236 in.)
d 21.0 mm (0.827 in.)




c.

Apply adhesive to the lower side window glass sub-assembly LH.

Adhesive:

Toyota Genuine Windshield Glass Adhesive or Equivalent



d.
B214800E32
2.479,0.573 2.958,0.406 true 1.198,0.479 1.344,0.604 false 0.563,0.604 0.813,0.844 0.25,0.24 10 false a 1.302,1.406 1.552,1.646 0.25,0.24 10 false a 0.771,1.021 1.021,1.26 0.25,0.24 10 false b 1.115,0.906 1.365,1.146 0.25,0.24 10 false b 2.99,0.292 3.24,0.531 0.25,0.24 10 false *1

Cut off the tip of the cartridge nozzle as shown in the illustration.

Standard:
Area Specified Condition
a 12.0 mm (0.472 in.)
b 8.0 mm (0.315 in.)


Text in Illustration
*1 Sealer Gun

HINT:

After cutting off the tip, use all adhesive within the time written in the table below.



e.

Apply adhesive to the glass as shown in the illustration.

NOTICE:

Allow the primer to dry for 3 minutes or more.


B471164E01
4.531,1.396 4.698,1.583 true 6.302,1.396 6.469,1.583 true 4.479,3.115 4.771,3.344 4.771,3.344 4.74,3.125 true 0.219,0.156 0.531,0.354 0.313,0.198 10 false *a 1.229,1.292 1.385,1.469 0.156,0.177 10 false A 1.25,1.677 1.406,1.854 0.156,0.177 10 false A 1.396,1.865 1.552,2.042 0.156,0.177 10 false C 1.281,2.25 1.438,2.427 0.156,0.177 10 false C 3.083,1.396 3.24,1.573 0.156,0.177 10 false B 2.719,1.458 2.875,1.635 0.156,0.177 10 true B 3.896,0.302 4.354,0.5 0.458,0.198 10 false A-A 5.615,0.292 6.073,0.49 0.458,0.198 10 false B-B 3.885,2.073 4.344,2.271 0.458,0.198 10 false C-C 4.667,0.51 4.823,0.708 0.156,0.198 10 false a 4.854,2.406 5.01,2.604 0.156,0.198 10 false b 6.438,0.49 6.594,0.688 0.156,0.198 10 false b 4.573,2.208 4.729,2.406 0.156,0.198 10 false c 4.75,1.552 4.99,1.719 0.24,0.167 10 false *b 6.51,1.563 6.75,1.729 0.24,0.167 10 false *b 4.75,3.396 4.99,3.563 0.24,0.167 10 false *b

Text in Illustration
*a Back Side *b Adhesive Center
V100155

Adhesive - -

Standard:
Area Specified Condition
a 15.0 mm (0.591 in.)
b 13.0 mm (0.512 in.)
c 8.0 mm (0.315 in.)



f.

Install the lower side window glass sub-assembly LH to the vehicle body.


g.

Press it in gently along the rim.

NOTICE:
·

Check that the pins are attached to the vehicle body correctly.

·

Check that the vehicle body and glass have a small gap between them.



HINT:

Press the glass with force of 98 N (10 kgf, 22.0 lbf) or more.



h.

Using a scraper, remove any excess or protruding adhesive.

NOTICE:

Apply adhesive to the glass rim.



Hide 5.INSPECT FOR LEAKS AND REPAIR

a.

After the adhesive has hardened, apply water from the outside of the vehicle. Check that no water leaks into the cabin.


b.

If water leaks into the cabin, allow the water to dry and add adhesive.


c.

Remove the protective tape.


Hide 62520G 6.INSTALL NO. 1 SIDE TRIM ASSEMBLY LH

Hide 62540A 7.INSTALL NO. 2 SIDE TRIM ASSEMBLY LH

Hide 67676 8.INSTALL FRONT SIDE TRIM BOARD COVER LH

Hide 73224 9.INSTALL FRONT SEAT BELT RETRACTOR COVER LH (w/ Rear No. 1 Seat)

Hide 62638A 10.INSTALL QUARTER PILLAR GARNISH RH

Hide 62989 11.INSTALL CENTER DOOR LOCK COVER (for Folding Type)

Hide 62547B 12.INSTALL NO. 3 PILLAR GARNISH LH

Hide 73220 13.CONNECT FRONT SEAT OUTER BELT ASSEMBLY LH (w/ Rear No. 1 Seat)

Hide 74730 14.INSTALL HAND GRIP FRAME ASSEMBLY (w/ Hand Grip Frame)

Hide 62425 15.INSTALL CENTER PILLAR GARNISH COVER (w/ Hand Grip Frame)

Hide 62212 16.INSTALL FRONT PILLAR GARNISH LH

HINT:

Use the same procedure described for the RH side.


Click hereVehicle Interior>INTERIOR>ROOF HEADLINING>INSTALLATION

Hide 17.INSTALL FRONT PILLAR END COVER LH

Hide 53182A 18.INSTALL HEADLIGHT COVER LH

Hide 87940 19.INSTALL OUTER REAR VIEW MIRROR ASSEMBLY LH


b.

w/o Power Retract Mirror:


Hide 87945 20.INSTALL OUTER MIRROR COVER LH


b.

w/o Power Retract Mirror: