Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM(for N04C Series Engine)
RM2850E _55 Steering _073197 POWER ASSIST SYSTEMS _0356229 POWER STEERING SYSTEM(for N04C Series Engine) G

POWER ASSIST SYSTEMS  POWER STEERING SYSTEM(for N04C Series Engine)  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 1.BLEED POWER STEERING SYSTEM

a.

Check the fluid level.


b.

Jack up the front of the vehicle and support it with stands.


c.

Turn the steering wheel.

i.

With the engine stopped, turn the steering wheel slowly from lock to lock several times.



d.

Lower the vehicle.


e.

Start the engine.

i.

Run the engine at idle for a few minutes.



f.

Turn the steering wheel.

i.

With the engine idling, turn the steering wheel to the left or right full lock position and keep it there for 2 to 3 seconds. Then turn the steering wheel to the opposite full lock position and keep it there for 2 to 3 seconds (step A).


ii.

Repeat step A several times.



g.

Stop the engine.


h.
F040897E19
0.323,0.24 1.135,0.427 0.813,0.188 10 false *a 2.135,0.24 3.094,0.427 0.958,0.188 10 false *b

Check for foaming or emulsification.

Text in Illustration
*a Normal
*b Abnormal

If the system has to be bled twice because of foaming or emulsification, check for fluid leakage in the system.


i.

Check the fluid level.


Hide 2.INSPECT FLUID LEVEL

a.
C145204

Keep the vehicle level.


b.

With the engine stopped, check the fluid level in the oil reservoir.

If necessary, add fluid.

Fluid:

ATF "DEXRON" II or III, or equivalent.


HINT:

Check that the fluid level is within the "HOT" level range in the reservoir tank. If the fluid is cold, check that it is within the "COLD" level range.



c.

Start the engine and let it idle.


d.

Turn the steering wheel from lock to lock several times to raise the fluid temperature.

Fluid temperature:

75 to 80°C (167 to 176°F)



e.
F040897E19
0.323,0.24 1.135,0.427 0.813,0.188 10 false *a 2.135,0.24 3.094,0.427 0.958,0.188 10 false *b

Check for foaming or emulsification.

Text in Illustration
*a Normal
*b Abnormal

If any foaming or emulsification is identified, bleed the power steering system.


f.
R011786E12
0.708,1.792 0.948,1.979 0.24,0.188 10 false *a 2.469,1.792 2.719,1.979 0.25,0.188 10 false *b 1.427,0.448 1.688,0.625 0.26,0.177 10 false *c

With the engine idling, measure the fluid level in the oil reservoir.

Text in Illustration
*a Engine Idling
*b Engine Stopped
*c 5 mm (0.20 in.) or less


g.

Stop the engine.


h.

Wait a few minutes and measure the fluid level in the oil reservoir again.

Maximum fluid level rise:

5 mm (0.20 in.)


If any problems are found, bleed the power steering system again.


i.

Check the fluid level.


Hide 3.INSPECT STEERING FLUID PRESSURE

a.

Disconnect the pressure feed hose from the vane pump (Click here Steering>POWER ASSIST SYSTEMS>VANE PUMP(for N04C Series Engine)>REMOVAL).


b.

Connect SST as shown in the illustration.

SST
09640-10011  (09641-01010, 09641-01020, 09641-01030)

C101994E02
3.083,0.438 3.292,0.219 false 3.948,2.323 4.188,1.99 true 6.427,1.99 6.125,2.323 true 0.604,0.677 0.854,0.854 0.25,0.177 10 false *1 3.771,2.323 4.01,2.5 0.24,0.177 10 false *1 5.948,2.333 6.167,2.521 0.219,0.188 10 false *1 5.313,0.552 5.583,0.74 0.271,0.188 10 false *3 6.427,0.552 6.667,0.74 0.24,0.188 10 false *4 4.125,0.542 4.385,0.729 0.26,0.188 10 false *2 3.333,0.104 3.677,0.292 0.344,0.188 10 false SST 2.563,1.281 2.802,1.458 0.24,0.177 10 false *a 3.677,1.26 3.927,1.438 0.25,0.177 10 false *b 1.917,0.677 2.167,0.854 0.25,0.177 10 false *1

Text in Illustration
*1 Attachment *2 PS Gear
*3 Oil Reservoir *4 Vane Pump
*a IN *b OUT

NOTICE:

Check that the valve of SST is in the open position.



c.

Bleed the power steering system.


d.

Start the engine and let it idle.


e.

Turn the steering wheel from lock to lock several times to raise the fluid temperature.

Fluid temperature:

75 to 80 °C (167 to 176 °F)



f.
C114329E05
0.438,0.792 0.646,0.969 0.208,0.177 10 false *1 2.719,1.469 2.969,1.646 0.25,0.177 10 false *3 2.719,0.188 2.938,0.354 0.219,0.167 10 false *2 1.354,1.073 1.667,1.26 0.313,0.188 10 false *a 1.51,1.875 1.844,2.083 0.333,0.208 10 false SST

With the engine idling, close the valve of SST and check the reading on SST.

Text in Illustration
*1 PS Gear
*2 Oil Reservoir
*3 Vane Pump
*a Closed

Fluid pressure:

10900 to 11700 kPa (111 to 119 kgf/cm2, 1581 to 1697 psi)


NOTICE:
·

Do not keep the valve closed for more than 10 seconds.

·

Do not let the fluid temperature become too high.




g.
C321700E01
0.458,0.802 0.719,1 0.26,0.198 10 false *1 2.719,0.208 2.979,0.406 0.26,0.198 10 false *2 2.74,1.479 3,1.677 0.26,0.198 10 false *3 1.354,1.063 1.615,1.26 0.26,0.198 10 false *a 1.51,1.885 1.875,2.073 0.365,0.188 10 false SST

With the engine idling, fully open the valve.

Text in Illustration
*1 PS Gear
*2 Oil Reservoir
*3 Vane Pump
*a Open


h.

Measure the fluid pressure at the engine speeds of 1000 rpm and 3000 rpm.

Fluid pressure difference:

490 kPa (5 kgf/cm2, 71 psi) or less


NOTICE:

Do not turn the steering wheel.



i.
C321701E01
0.438,0.823 0.75,1.021 0.313,0.198 10 false *1 1.542,0.417 1.792,0.615 0.25,0.198 10 false *b 1.354,1.063 1.604,1.26 0.25,0.198 10 false *a 1.49,1.875 1.833,2.073 0.344,0.198 10 false SST 2.729,0.219 3.042,0.417 0.313,0.198 10 false *2 2.74,1.51 3.052,1.708 0.313,0.198 10 false *3

With the engine idling and valve fully open, turn the steering wheel to the full lock position.

Text in Illustration
*1 PS Gear
*2 Oil Reservoir
*3 Vane Pump
*a Open
*b Lock Position

Fluid pressure:

10900 to 11700 kPa (111 to 119 kgf/cm2, 1581 to 1697 psi)


NOTICE:
·

Do not keep the steering wheel in the full lock position for more than 10 seconds.

·

Do not let the fluid temperature become too high.




j.

Disconnect SST.


k.

Connect the pressure feed hose to the vane pump (Click here Steering>POWER ASSIST SYSTEMS>VANE PUMP(for N04C Series Engine)>INSTALLATION).


l.

Bleed the power steering system.


Hide 4.INSPECT STEERING EFFORT

a.
C153792

Center the steering wheel assembly.



c.

Start the engine and let it idle.


d.

Measure the steering effort in both directions.

Torque:
Steering effort (Reference):

6.0 N*m (61 kgf*cm, 53 in.*lbf) or less


HINT:

Check the tire type, pressure and contact surfaces before making a diagnosis.