Home › Engine / Hybrid System › 1BZ-FPE (ENGINE MECHANICAL) › CYLINDER BLOCK › 2017.01–2021.01
RM2850E _51 Engine / Hybrid System _073200 1BZ-FPE ENGINE MECHANICAL _0356246 CYLINDER BLOCK A

1BZ-FPE ENGINE MECHANICAL  CYLINDER BLOCK  DISASSEMBLY  


PROCEDURE

Hide 13405 1.REMOVE FLYWHEEL

Hide 2.REMOVE FLYWHEEL HOUSING

Hide 11355 3.REMOVE REAR END PLATE

Hide 4.INSTALL ENGINE TO ENGINE STAND FOR DISASSEMBLY

Hide 27020 5.REMOVE ALTERNATOR AND BRACKET

Hide 13523 8.REMOVE TIMING GEARS AND CAMSHAFT

Hide 12101 9.REMOVE OIL PAN, OIL STRAINERANDTIMING GEAR CASE (OIL PUMP)

Hide 11452 10.REMOVE OIL DIPSTICK AND GUIDE

Hide 15710 11.REMOVE OIL FILTER AND OIL COOLER ASSEMBLIES

Hide 83530 12.REMOVE OIL PRESSURE SWITCH

Hide 13613C 13.REMOVE OIL NOZZLE FOR TIMING GEARS

Hide 14.REMOVE WATER DRAIN UNION

Hide 12311 15.REMOVE ENGINE MOUNTING BRACKET

Hide 11381 16.REMOVE REAR OIL SEAL RETAINER

a.
A423730

Remove the 6 bolts, oil seal retainer and gasket.


Hide 13201 17.CHECK CONNECTING ROD THRUST CLEARANCE

a.
A423732

Using a dial indicator, measure the thrust clearance while moving the connecting rod back and forth.

Standard thrust clearance:

0.200 - 0.320 mm (0.0079 - 0.0126 in.)


Maximum thrust clearance:

0.40 mm (0.0157 in.)


If the thrust clearance is greater than maximum, replace the connecting rod assembly, If necessary, replace the crankshaft.


Hide 18.REMOVE CONNECTING ROD CAPS AND CHECK OIL CLEARANCE

a.
A423733

Using a punch or numbering stamp, place matchmarks on the connecting rod and cap to ensure correct reassembly.


b.
A423734

Remove the 2 connecting rod cap nuts.


c.
A423735

Using a plastic-faced hammer, lightly tap the connecting rod bolts and lift off the connecting rod cap.

HINT:

Keep the lower bearing inserted with the connecting rod cap.



d.
A423736

Cover the connecting rod bolts with a short piece of hose to protect the crankshaft form damage.


e.

Clean the crank pin and bearing.


f.

Check the crank pin and bearing for pitting and scratches.

If the crank pin or bearing is damaged, replace the bearings.

If necessary, grind or replace the crankshaft.


g.
A423737

Lay a strip of Plastigage across the crank pin.


h.

Install the connecting rod cap with the 2 nuts.

(See step 8 in cylinder block assembly)

Torque:

1st: 68.6 N*m (700 kgf*cm, 51 ft*lbf)

2nd: Turn 90 °


NOTICE:

Do not turn the crankshaft.



i.

Remove the 2 nuts, connecting rod cap and lower bearing. (See procedure (b) and (c) above)


j.
A423738

Measure the Plastigage at its widest point.

Standard oil clearance:
STD:

0.030 - 0.070 mm (0.0012 - 0.0028 in.)

U/S 0.25, 0.50, 1.00:

0.030 - 0.072 mm (0.0012 - 0.0028 in.)


Maximum oil clearance:

0.10 mm (0.0039 in.)


If the oil clearance is greater than maximum, replace the bearings. If necessary, grind or replace the crankshaft.

HINT:
A423739

There are 2 sizes of standard bearings, colored yellow and green, if using a standard bearings, select one having the color corresponding to the number on the bearing cap:

1 with Yellow

2 with Green


Reference:
Standard sized bearing center wall thickness:
Yellow 1.480 - 1.485 mm (0.0583 - 0.0585 in.)
Green 1.486 - 1.490 mm (0.0585 - 0.0587 in.)



k.

Completely remove the Plastigage.


Hide 13101 19.REMOVE PISTON AND CONNECTING ROD ASSEMBLIES

a.
A423740

Using a ridge reamer, remove all the carbon from the top of the cylinder.


b.

Push the piston, connecting rod assembly and upper bearing through the top of the cylinder block.

·

Keep the bearings, connecting rod and cap together.

·

Arrange the piston and connecting rod assemblies in correct order.



Hide 13411 20.CHECK CRANKSHAFT THRUST CLEARANCE

a.
A423741

Using a dial indicator, measure the thrust clearance while prying the crankshaft back and forth with a screwdriver.

Standard thrust clearance:

0.040 - 0.250 mm (0.0016 - 0.0098 in.)


Maximum thrust clearance:

0.30 mm (0.0118 in.)


If the thrust clearance is greater than maximum, replace the thrust washers as a set.

Thrust washer thickness:
STD:

2.430 - 2.480 mm (0.0957 - 0.0976 in.)

O/S 0.125:

2.493 - 2.543 mm (0.0981 - 0.1001 in.)

O/S 0.250:

2.555 - 2.605 mm (0.1006 - 0.1026 in.)



Hide 21.REMOVE MAIN BEARING CAPS AND CHECK OIL CLEARANCE

a.
A423742

Remove the 10 main bearing cap bolts.


b.
A423743

Using the removed main bearing cap bolts, pry the cap back and forth, and remove the main bearing caps, lower thrust washers (No.3 main bearing cap only).


c.

Lift out the crankshaft.

HINT:
·

Keep the upper bearings inserted with the cylinder block.

·

Arrange the thrust washers in correct order.




d.

Clean each main journal and bearing.


e.

Check each main journal and bearing for pitting and scratches.

If the journal or bearing is damaged, replace the bearings. If necessary, grind or replace the crankshaft.


f.

Place the crankshaft on the cylinder block.


g.
A423744

Lay a strip of Plastigage across each journal.


h.

Install the 5 main bearing caps with the 10 bolts. (See step 6 in cylinder block assembly)

Torque:

200 N*m (2,039 kgf*cm, 148 ft*lbf)


NOTICE:

Do not turn the crankshaft.



i.

Remove the 10 bolts and 5 main bearing caps. (See procedure (b) and (c) above)


j.
A423745

Measure the Plastigage at its widest point.

Standard oil clearance:
No.3 journal:

STD: 0.060 - 0.104 mm (0.0024 - 0.0041 in.)

U/S 0.25, 0.50, 1.00: 0.060 - 0.106 mm (0.0026 - 0.0042 in.)

Others:

STD: 0.030 - 0.074 mm (0.0012 - 0.0029 in.)

U/S 0.25, 0.50, 1.00: 0.030 - 0.076 mm (0.0012 - 0.0030 in.)


Maximum clearance:

No.3 journal: 0.15 mm (0.0059 in.)

Others: 0.10 mm (0.0039 in.)


If the oil clearance is greater than maximum, replace the bearings. If necessary, grind or replace the crankshaft.

HINT:
A423746

There are 2 sizes of standard bearings, colored yellow and green. If using a standard bearing, select one having the color corresponding to the number on the cylinder block:

1 with Yellow

2 with Green


Reference:
Standard sized bearing center wall thickness:
Yellow 1.480 - 1.485 mm (0.0583 - 0.0585 in.)
Green 1.486 - 1.490 mm (0.0585 - 0.0587 in.)



k.

Completely remove the Plastigage.


Hide 13411 22.REMOVE CRANKSHAFT

a.

Lift out the crankshaft.


b.

Remove the upper bearings and thrust washers form the cylinder block.

HINT:

Arrange the main bearing caps, bearings and thrust washers in correct order.



Hide 13613C 23.REMOVE CHECK VALVES AND OIL NOZZLES

Hide 13751 24.REMOVE VALVE LIFTERS

a.
A423747

Remove the 8 (B) bolts.

NOTICE:

With the engine in the upside down position, the lifters will drop in the engine if the (A) bolts are removed.



b.

Remove the 8 (A) bolts, if necessary.


c.
A423748

Pull out valve lifters.

HINT:

Arrange the valve lifters in correct order.



Hide 25.CHECK FIT BETWEEN PISTON AND PISTON PIN

a.
A423749

Try to move the piston back and forth on the piston pin.

If any movement is felt, replace the piston and pin a as set.


Hide 13011 26.REMOVE PISTON RINGS

a.
A423750

Using a piston ring expander, remove the No.1, No.2 and oil rings.


b.

Remove the coil by hand.

HINT:

Arrange the rings in correct order only.



Hide 13201 27.DISCONNECT CONNECTING ROD FROM PISTON

a.
A423751

Using needle-nose pliers, remove the snap rings.


b.
A423752

Gradually heat the piston to approx. 60 °C (140 °F).


c.

Using a plastic-faced hammer and brass bar, lightly tap out the piston pin and remove the connecting rod.

HINT:
·

The piston and pin are a matched set.

·

Arrange the pistons, pins, rings, connecting rods and bearings in correct order.