Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM
RM2850E _54 Brake _073264 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0356689 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1405  Open or Short in Front Speed Sensor RH Circuit  C1406  Open or Short in Front Speed Sensor LH Circuit  


DESCRIPTION

Refer to DTCs C1401 and C1402 (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>C1401).

DTC No. DTC Detection Condition Trouble Area
C1405
C1406
Either of the following is detected:
1.

An open in the speed sensor signal circuit continues for 0.5 seconds or more.

2.

With the +BS terminal voltage at 9.5 V or higher, the sensor power supply voltage decreases for 0.5 seconds or more.


·

Front speed sensor RH/LH

·

Skid control ECU (Brake actuator assembly)

·

Wire harness or connector



HINT:
·

DTC C1405 is for the front speed sensor RH.

·

DTC C1406 is for the front speed sensor LH.



WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake actuator assembly), perform zero point calibration and store system information (Click HereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).


PROCEDURE

1.READ VALUE USING GTS (FRONT SPEED SENSOR)
a.

Using the GTS, check for any momentary interruption in the wire harness and connector corresponding to the DTC (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CHECK FOR INTERMITTENT PROBLEMS).

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
FR Speed Sensor Voltage Open Front speed sensor RH voltage open detection / Error or Normal Normal Error: Momentary interruption
FL Speed Sensor Voltage Open Front speed sensor LH voltage open detection / Error or Normal Normal Error: Momentary interruption
FR Speed Open Momentary interruption of front speed sensor RH pulse input to ECU / Error or Normal Normal Error: Momentary interruption
FL Speed Open Momentary interruption of front speed sensor LH pulse input to ECU / Error or Normal Normal Error: Momentary interruption

HINT:

Perform the above inspection before removing the sensor and connector.


OK:

Normal (There are no momentary interruptions.)



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - FRONT SPEED SENSOR)
2.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - FRONT SPEED SENSOR)
a.

Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.


c.

Disconnect the A71 skid control ECU (brake actuator assembly) connector.


d.

Disconnect the B3 or B1 front speed sensor connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RH:
Tester Connection Condition Specified Condition
A71-31 (FR+) - B3-3 (FR+) Always Below 1 Ω
A71-31 (FR+) or B3-3 (FR+) - Body ground Always 10 kΩ or higher
A71-30 (FR-) - B3-1 (FR-) Always Below 1 Ω
A71-30 (FR-) or B3-1 (FR-) - Body ground Always 10 kΩ or higher

for LH:
Tester Connection Condition Specified Condition
A71-18 (FL+) - B1-3 (FL+) Always Below 1 Ω
A71-18 (FL+) or B1-3 (FL+) - Body ground Always 10 kΩ or higher
A71-17 (FL-) - B1-1 (FL-) Always Below 1 Ω
A71-17 (FL-) or B1-1 (FL-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT BRAKE ACTUATOR ASSEMBLY (SENSOR INPUT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT BRAKE ACTUATOR ASSEMBLY (SENSOR INPUT)
a.
C269767E01
1.552,0.417 1.896,0.635 0.344,0.219 1.552,0.094 1.896,0.313 0.344,0.219 1.948,1.313 2.74,1.458 2.74,1.458 2.74,1.635 true 0.125,0.063 0.438,0.26 0.313,0.198 10 false *a 1.625,0.115 1.938,0.313 0.313,0.198 10 false B3 1.635,0.448 1.948,0.646 0.313,0.198 10 false B1 2,0.104 2.313,0.302 0.313,0.198 10 false *A 2.01,0.438 2.323,0.635 0.313,0.198 10 false *B 2.531,1.708 3.073,1.938 0.542,0.229 10 false FR+*A 2.552,1.896 3.052,2.115 0.5,0.219 10 false FL+*B

Reconnect the A71 skid control ECU (brake actuator assembly) connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for RH:
Tester Connection Condition Specified Condition
B3-3 (FR+) - Body ground Ignition switch ON 8 to 14 V

for LH:
Tester Connection Condition Specified Condition
B1-3 (FL+) - Body ground Ignition switch ON 8 to 14 V


Text in Illustration
*A for RH
*B for LH
*a Front view of wire harness connector
(to Front Speed Sensor)

NOTICE:

Check the speed sensor signal after replacement (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE).



Result:
Proceed to
OK
NG



OK

NG