Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM
RM2850E _54 Brake _073264 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0356689 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1401  Front Speed Sensor RH Malfunction  C1402  Front Speed Sensor LH Malfunction  


DESCRIPTION

The speed sensor detects the wheel speed and sends the appropriate signals to the skid control ECU (brake actuator assembly). These signals are used for brake control.

The speed sensor generates vehicle speed pulses based on the rotation of the skid control rotor. The skid control ECU (brake actuator assembly) detects the speed of each wheel using this vehicle speed pulse.

HINT:

When the connectors between the speed sensor and skid control ECU (brake actuator assembly) are connected, the following waveform is output.


C371023E01
0.844,1.167 0.479,0.635 true 2.542,2.156 2.042,1.792 true 0.323,0.469 0.635,0.667 0.313,0.198 10 false *1 2.604,2.156 2.917,2.354 0.313,0.198 10 false *2 4.823,0.438 5.135,0.635 0.313,0.198 10 false *a 4.302,1.531 4.615,1.729 0.313,0.198 10 false *b 5.323,1.531 5.635,1.729 0.313,0.198 10 false *c 6.24,0.708 6.771,0.948 0.531,0.24 10 false 1.4 V 6.26,1.115 6.75,1.333 0.49,0.219 10 false 0.7 V

Text in Illustration
*1 Front Speed Sensor *2 Front Skid Control Rotor
*a Waveform (Reference):
Between Speed Sensor (-) and Body Ground
*b Low speed
*c High speed - -

DTC No. DTC Detection Condition Trouble Area
C1401
C1402
Either of the following is detected:
1.

At a vehicle speed of 10 km/h (6 mph) or more, output voltage from one of the speed sensors is less than that from the other sensors for 15 seconds or more.

2.

At a vehicle speed less than 10 km/h (6 mph), output from one of the speed sensors is 0 km/h (0 mph) for 1 second or more.

3.

At a vehicle speed of 10 km/h (6 mph) or more, outputs from both front speed sensors are 0 km/h (0 mph) for 15 seconds or more. (except both rear speed sensors are 0 km/h (0 mph))


·

Front speed sensor RH/LH

·

Sensor installation

·

Front skid control rotor RH/LH



HINT:
·

DTC C1401 is for the front speed sensor RH.

·

DTC C1402 is for the front speed sensor LH.



WIRING DIAGRAM

C321037E01
1.292,0.573 1.542,0.792 0.25,0.219 10 false 1 1.552,0.688 1.938,0.906 0.385,0.219 10 false FR- 2.24,0.677 2.615,0.896 0.375,0.219 10 false FR+ 2.635,0.573 2.885,0.792 0.25,0.219 10 false 3 1.156,0.99 1.479,1.208 0.323,0.219 10 false B3 1.156,1.177 2.823,1.448 1.667,0.271 10 false Front Speed Sensor RH 1.292,2.281 1.542,2.5 0.25,0.219 10 false 1 1.552,2.417 1.844,2.635 0.292,0.219 10 false FL- 2.25,2.417 2.594,2.625 0.344,0.208 10 false FL+ 2.635,2.292 2.885,2.51 0.25,0.219 10 false 3 1.052,2.688 1.375,2.896 0.323,0.208 10 false B1 1.052,2.885 2.771,3.146 1.719,0.26 10 false Front Speed Sensor LH 5.563,0.573 5.813,0.792 0.25,0.219 10 false 31 5.563,1.458 5.813,1.677 0.25,0.219 10 false 30 5.563,2.281 5.813,2.5 0.25,0.219 10 false 18 5.563,3.198 5.813,3.417 0.25,0.219 10 false 17 5.917,0.677 6.281,0.896 0.365,0.219 10 false FR+ 5.917,1.583 6.25,1.802 0.333,0.219 10 false FR- 5.906,2.417 6.26,2.635 0.354,0.219 10 false FL+ 5.917,3.313 6.229,3.531 0.313,0.219 10 false FL- 5.583,3.833 5.927,4.052 0.344,0.219 10 false A71 5.583,4.021 7.135,4.406 1.552,0.385 10 false Skid Control ECU (Brake Actuator Assembly)

PROCEDURE

1.CHECK FRONT SPEED SENSOR INSTALLATION
a.

Turn the ignition switch off.


b.
C168336E26
0.698,0.385 1.01,0.583 0.313,0.198 10 false *a 2.292,0.385 2.604,0.583 0.313,0.198 10 false *b 2.01,1.656 2.323,1.854 0.313,0.198 10 false *c

Check the speed sensor installation (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>FRONT SPEED SENSOR (w/ Brake pedal Load Sensing Switch)>INSTALLATION).

OK:

There is no clearance between the sensor and the front steering knuckle.

The installation bolt is tightened properly.


Text in Illustration
*a Normal
*b Abnormal
*c Clearance


Result:
Proceed to
OK
NG



OK

2.INSPECT FRONT SPEED SENSOR TIP

NG

2.INSPECT FRONT SPEED SENSOR TIP

b.

Check the speed sensor tip.

OK:

No scratches, oil, or foreign matter on the sensor tip.


NOTICE:
·

If no damage to the speed sensor tip is found during this inspection, do not replace the speed sensor.

·

If there is iron powder sticking to the rotor, this will result in a malfunction, so confirm that the rotor is not contaminated with foreign material before replacing the sensor.

·

Check the speed sensor signal after cleaning or replacement (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE).




Result:
Proceed to
OK
NG



OK

3.INSPECT FRONT SKID CONTROL ROTOR

NG

CLEAN OR REPLACE FRONT SPEED SENSOR

3.INSPECT FRONT SKID CONTROL ROTOR
a.

Remove the front axle hub and disc assembly (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>FRONT SKID CONTROL ROTOR>REMOVAL).


b.

Check the front skid control rotor.

OK:

No scratches, oil or foreign matter on the rotor.


NOTICE:

Check the speed sensor signal after cleaning or replacement (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE).



c.

Reinstall the front speed sensor and front axle hub and disc assembly (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>FRONT SPEED SENSOR (w/ Brake pedal Load Sensing Switch)>INSTALLATION for front speed sensor, Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>FRONT SKID CONTROL ROTOR>INSTALLATION for front axle hub and brake disc assembly).


Result:
Proceed to
OK
NG



OK

4.READ VALUE USING GTS (FRONT SPEED SENSOR)

NG

CLEAN OR REPLACE FRONT SKID CONTROL ROTOR

4.READ VALUE USING GTS (FRONT SPEED SENSOR)
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Start the engine.


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.


f.

According to the display on the GTS, read the Data List.

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
FR Wheel Speed Front wheel speed sensor RH reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
FL Wheel Speed Front wheel speed sensor LH reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations


g.

Check that there is no difference between the speed value output from the speed sensor displayed on the GTS and the speed value displayed on the speedometer when driving the vehicle.

HINT:

Factors that affect the indicated vehicle speed include tire size, tire inflation, and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, see the reference chart (Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>ON-VEHICLE INSPECTION).


OK:

The speed value output from the speed sensor displayed on the GTS is similar to the speed indicated on the speedometer.



HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE).


Result:
Proceed to
OK
NG



OK

NG

5.REPLACE FRONT SPEED SENSOR
5.REPLACE FRONT SPEED SENSOR
a.

Turn the ignition switch off.



Result:
Proceed to
NEXT



NEXT

6.RECONFIRM DTC
6.RECONFIRM DTC

b.

Turn the ignition switch off.


c.

Start the engine.


d.

Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.


e.

Check if the same DTC is recorded (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTCs C1401 and C1402 are not output A
DTCs C1401 and/or C1402 are output B


NOTICE:

Check the speed sensor signal after replacement (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE).




A

END

B