Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM
RM2850E _54 Brake _073264 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0356689 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1415  Rear Speed Sensor RH Output Malfunction  C1416  Rear Speed Sensor LH Output Malfunction  


DESCRIPTION

Refer to DTCs C1403 and C1404 (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>C1403).

DTC No. DTC Detection Condition Trouble Area
C1415
C1416
Either of the following is detected:
1.

An open in the sensor signal circuit of a malfunctioning area occurs 255 times or more.

2.

At a vehicle speed of 20 km/h (12 mph) or more, noise occurs in the sensor signals of a malfunctioning wheel 75 times or more within 5 seconds.

3.

At a vehicle speed of 10 km/h (6 mph) or more, noise occurs once per rotor rotation for 15 seconds or more.


·

Rear speed sensor RH/LH

·

Rear skid control rotor RH/LH

·

Sensor installation



HINT:
·

DTC C1415 is for the rear speed sensor RH.

·

DTC C1416 is for the rear speed sensor LH.



PROCEDURE

1.READ VALUE USING GTS (REAR SPEED SENSOR)
a.

According to the display on the GTS, display the Data List, perform a driving test based on the conditions when the problem occurred (determined from the freeze frame data or customer problem analysis results) and check the Data List when the vehicle is running and stopped (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DATA LIST / ACTIVE TEST).

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
RR Wheel Speed Rear wheel speed sensor RH reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
RL Wheel Speed Rear wheel speed sensor LH reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
RR Speed Open Momentary interruption of rear speed sensor RH pulse input to ECU Normal Error: Momentary interruption
RL Speed Open Momentary interruption of rear speed sensor LH pulse input to ECU Normal Error: Momentary interruption

OK:

Output value does not change and no interruptions occur according to vehicle speed


NOTICE:

Perform the above inspection before removing the sensor and connector.



Result:
Proceed to
OK
NG



OK

NG

2.CHECK REAR SPEED SENSOR INSTALLATION
2.CHECK REAR SPEED SENSOR INSTALLATION
a.

Turn the ignition switch off.


b.
C168336E26
0.698,0.385 1.01,0.583 0.313,0.198 10 false *a 2.292,0.385 2.604,0.583 0.313,0.198 10 false *b 2.01,1.656 2.323,1.854 0.313,0.198 10 false *c

Check the rear speed sensor installation.

OK:

There is no clearance between the sensor and the rear axle housing.

The installation bolt is tightened properly.


Text in Illustration
*a Normal
*b Abnormal
*c Clearance


Result:
Proceed to
OK
NG



OK

3.INSPECT REAR SPEED SENSOR (Foreign Matter Adhesion)

NG

3.INSPECT REAR SPEED SENSOR (Foreign Matter Adhesion)
a.

Remove the wheel speed sensor corresponding to the DTC and check that the tip is free from oil and foreign matter.

OK:

There is no oil or foreign matter


NOTICE:

This DTC may be detected if foreign matter 1 mm (0.03937 in.) x 1 mm (0.03937 in.) or larger is attached.



Result:
Proceed to
OK
NG



OK

4.INSPECT REAR SKID CONTROL ROTOR (Foreign Matter Adhesion)

NG

7.CLEAN REAR SPEED SENSOR
4.INSPECT REAR SKID CONTROL ROTOR (Foreign Matter Adhesion)
a.

Check that there are no foreign objects or oil on the skid control rotor that was indicated by the DTC.

OK:

There is no oil or foreign matter


HINT:

This DTC may be detected if foreign matter 1 mm (0.03937 in.) x 1 mm (0.03937 in.) or larger is attached.



Result:
Proceed to
OK
NG



OK

NG

5.CLEAN REAR SKID CONTROL ROTOR
5.CLEAN REAR SKID CONTROL ROTOR
a.

Clean the rear skid control rotor.

NOTICE:

Do not use a cleaner to clean the rear skid control rotor.



Result:
Proceed to
NEXT



NEXT

6.READ VALUE USING GTS (REAR SPEED SENSOR)
6.READ VALUE USING GTS (REAR SPEED SENSOR)
a.

According to the display on the GTS, display the Data List, perform a driving test based on the conditions when the problem occurred (determined from the freeze frame data or customer problem analysis results) and check the Data List when the vehicle is running and stopped (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DATA LIST / ACTIVE TEST).

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
RR Wheel Speed Rear wheel speed sensor RH reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
RL Wheel Speed Rear wheel speed sensor LH reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
RR Speed Open Momentary interruption of rear speed sensor RH pulse input to ECU Normal Error: Momentary interruption
RL Speed Open Momentary interruption of rear speed sensor LH pulse input to ECU Normal Error: Momentary interruption

OK:

Output value does not change and no interruptions occur according to vehicle speed


NOTICE:

Perform the above inspection before removing the sensor and connector.



Result:
Proceed to
OK
NG



OK

END

NG

7.CLEAN REAR SPEED SENSOR
a.

Clean the rear speed sensor.

NOTICE:

When cleaning the rear speed sensor, clean the sensor mounting hole before installing the sensor.



Result:
Proceed to
NEXT



NEXT

8.READ VALUE USING GTS (REAR SPEED SENSOR)
8.READ VALUE USING GTS (REAR SPEED SENSOR)
a.

According to the display on the GTS, display the Data List, perform a driving test based on the conditions when the problem occurred (determined from the freeze frame data or customer problem analysis results) and check the Data List when the vehicle is running and stopped (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DATA LIST / ACTIVE TEST).

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
RR Wheel Speed Rear wheel speed sensor RH reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
RL Wheel Speed Rear wheel speed sensor LH reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
RR Speed Open Momentary interruption of rear speed sensor RH pulse input to ECU Normal Error: Momentary interruption
RL Speed Open Momentary interruption of rear speed sensor LH pulse input to ECU Normal Error: Momentary interruption

OK:

Output value does not change and no interruptions occur according to vehicle speed


NOTICE:

Perform the above inspection before removing the sensor and connector.



Result:
Proceed to
OK
NG



OK

END

NG

4.INSPECT REAR SKID CONTROL ROTOR (Foreign Matter Adhesion)