Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM
RM2850E _54 Brake _073264 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0356689 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1434  Steering Angle Sensor Output Malfunction  


DESCRIPTION

Steering angle sensor signals are input to the skid control ECU (brake actuator assembly) via the CAN communication system.

HINT:

When a malfunction occurs in the communication line to the steering angle sensor, U0126 is output. If a DTC related to the CAN communication line is output, first troubleshoot the CAN communication line.


DTCs may be stored if one of the following occurs:

·

Steering angle sensor zero point malfunction

·

Steering angle sensor signal malfunction


DTC No. DTC Detection Condition Trouble Area
C1434 Normal communication between the skid control ECU and the steering angle sensor and abnormal steering angle sensor zero point.
·

ECU-B NO. 3 fuse

·

ECU-IG1 NO. 3 fuse

·

Sensor installation

·

Steering angle sensor (Spiral with sensor cable sub-assembly)

·

Skid control ECU (Brake actuator assembly)

·

Wire harness or connector



CAUTION / NOTICE / HINT

NOTICE:
·

Do not remove the steering angle sensor from the spiral with sensor cable sub-assembly.

·

When replacing the steering angle sensor (spiral with sensor cable sub-assembly), confirm that the replacement part is of the correct specification.

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



HINT:
·

When U0073, U0124 and/or U0126 is output together with C1434, inspect and repair the trouble areas indicated by U0073, U0124 and/or U0126 first (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>U0073).

·

When any of the speed sensors or the yaw rate and acceleration sensor (airbag ECU assembly) has trouble, DTCs for the steering angle sensor (spiral with sensor cable sub-assembly) may be output even when the steering angle sensor (spiral with sensor cable sub-assembly) is normal. When DTCs for the speed sensors or yaw rate and acceleration sensor (airbag ECU assembly) are output together with DTCs for the steering angle sensor (spiral with sensor cable sub-assembly), inspect and repair the speed sensor and yaw rate and acceleration sensor (airbag ECU assembly) first, and then inspect and repair the steering angle sensor (spiral with sensor cable sub-assembly).



PROCEDURE

1.CHECK DTC

b.

Turn the ignition switch off.


c.

Turn the ignition switch to ON again and check that no CAN communication system DTC is output (Click herePower Source / Network>CAN COMMUNICATION>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM).


d.

Start the engine.


e.

Drive the vehicle at a speed of 35 km/h (22 mph) and turn the steering wheel to the right and left to check that no speed sensor or yaw rate and acceleration sensor DTCs are output (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
No CAN communication system, speed sensor, or yaw rate and acceleration sensor DTCs are output A
CAN communication system DTC is output B
Speed sensor or yaw rate and acceleration sensor DTC is output C


HINT:
·

If there is a malfunction in any of the speed sensors or the yaw rate and acceleration sensor (airbag ECU assembly), an abnormal value may be output although the steering angle sensor (spiral with sensor cable sub-assembly) sensor is normal.

·

If speed sensor and yaw rate and acceleration sensor (airbag ECU assembly) DTCs are output simultaneously, repair these two sensors first and inspect the steering angle sensor (spiral with sensor cable sub-assembly).





A

2.CHECK SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY INSTALLATION

B

C

2.CHECK SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY INSTALLATION
a.

Turn the ignition switch off.


b.

Check that the spiral with sensor cable sub-assembly has been installed properly (Click HereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>STEERING ANGLE SENSOR (w/ Brake pedal Load Sensing Switch)>INSTALLATION).

OK:

The steering angle sensor installation is normal.



Result:
Proceed to
OK
NG



OK

3.CHECK TERMINAL VOLTAGE (POWER SOURCE TERMINAL)

NG

3.CHECK TERMINAL VOLTAGE (POWER SOURCE TERMINAL)
a.

Turn the ignition switch off.


b.
C371519E01
0.292,0.969 0.667,1.177 0.375,0.208 1.708,1.719 2.135,1.302 true 2.906,1.542 2.417,1.271 true 0.177,0.115 0.49,0.313 0.313,0.198 10 false *a 0.375,0.99 0.688,1.188 0.313,0.198 10 false J71 1.594,1.75 2.021,1.948 0.427,0.198 10 false IG1 2.833,1.573 3.156,1.781 0.323,0.208 10 false BAT

Remove the steering wheel and the column cover.


c.

Make sure that there is no looseness at the locking part and the connecting part of the connector.


d.

Disconnect the J71 steering angle sensor (spiral with sensor cable sub-assembly) connector.


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
J71-6 (BAT) - Body ground Always 11 to 14 V
J71-5 (IG1) - Body ground Ignition switch ON 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Steering Angle Sensor (Spiral with Sensor Cable Sub-assembly))


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (ESS TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

4.CHECK HARNESS AND CONNECTOR (ESS TERMINAL)
a.
C371519E02
0.292,0.969 0.667,1.177 0.375,0.208 1.146,1.688 1.344,1.313 true 0.177,0.115 0.49,0.313 0.313,0.198 10 false *a 0.375,0.99 0.688,1.188 0.313,0.198 10 false J71 0.99,1.75 1.417,1.948 0.427,0.198 10 false ESS

Turn the ignition switch off.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J71-2 (ESS) - Body ground Always Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Steering Angle Sensor (Spiral with Sensor Cable Sub-assembly))


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (ESS CIRCUIT)