Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM
RM2850E _54 Brake _073264 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0356689 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1407  Open or Short in Rear Speed Sensor RH Circuit  C1408  Open or Short in Rear Speed Sensor LH Circuit  


DESCRIPTION

Refer to DTCs C1403 and C1404 (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>C1403).

DTC No. DTC Detection Condition Trouble Area
C1407
C1408
Either of the following is detected:
1.

An open in the speed sensor signal circuit continues for 0.5 seconds or more.

2.

With the +BS terminal voltage at 9.5 V or higher, the sensor power supply voltage decreases for 0.5 seconds or more.


·

Rear speed sensor RH/LH

·

Wire harness or connector

·

Rear skid control sensor wire

·

Skid control ECU (Brake actuator assembly)



HINT:
·

DTC C1407 is for the rear speed sensor RH.

·

DTC C1408 is for the rear speed sensor LH.



WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake actuator assembly), perform zero point calibration and store system information (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).


PROCEDURE

1.READ VALUE USING GTS (REAR SPEED SENSOR)
a.

Using the GTS, check for any momentary interruption in the wire harness and connector corresponding to the DTC (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CHECK FOR INTERMITTENT PROBLEMS).

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
RR Speed Sensor Voltage Open Rear speed sensor RH voltage open detection / Error or Normal Normal Error: Momentary interruption
RL Speed Sensor Voltage Open Rear speed sensor LH voltage open detection / Error or Normal Normal Error: Momentary interruption
RR Speed Open Momentary interruption of rear speed sensor RH pulse input to ECU / Error or Normal Normal Error: Momentary interruption
RL Speed Open Momentary interruption of rear speed sensor LH pulse input to ECU / Error or Normal Normal Error: Momentary interruption

HINT:

Perform the above inspection before removing the sensor and connector.


OK:

Normal (There are no momentary interruptions.)



Result:
Proceed to
OK
NG



OK

NG

2.INSPECT REAR SKID CONTROL SENSOR WIRE
2.INSPECT REAR SKID CONTROL SENSOR WIRE
a.

Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.



d.

Measure the resistance according to the value(s) in the table below.

C371275E01
1.104,0.708 1.406,0.906 0.302,0.198 3.448,0.708 3.771,0.906 0.323,0.198 5.813,0.708 6.115,0.906 0.302,0.198 0.573,0.927 1.063,1.479 true 1.51,1.479 1.969,0.99 true 5.25,0.885 5.729,1.469 true 6.167,1.5 6.698,0.885 true 0.177,0.135 0.49,0.333 0.313,0.198 10 false *1 0.385,0.76 0.698,0.958 0.313,0.198 10 false RL- 1.188,0.708 1.5,0.906 0.313,0.198 10 false p3 1.469,0.708 1.781,0.906 0.313,0.198 10 false *B 1.99,0.76 2.302,0.958 0.313,0.198 10 false RL+ 1.177,2.292 1.49,2.49 0.313,0.198 10 false *a 3.542,2.292 3.854,2.49 0.313,0.198 10 false *b 5.875,2.281 6.188,2.479 0.313,0.198 10 false *a 6.708,0.688 7.021,0.885 0.313,0.198 10 false RR+ 5.021,0.74 5.365,0.958 0.344,0.219 10 false RR- 5.896,0.708 6.208,0.906 0.313,0.198 10 false p4 6.188,0.708 6.5,0.906 0.313,0.198 10 false *A 3.49,0.729 3.865,0.958 0.375,0.229 10 false Pp1

Text in Illustration
*A for RH *B for LH
*1 Rear Skid Control Sensor Wire - -
*a Front view of wire harness connector
(to Sensor Side Connector)
*b Front view of wire harness connector
(to Vehicle Side Connector)

Standard Resistance:
for RH:
Tester Connection Condition Specified Condition
Pp1-5 - p4-1 (RR+) Always Below 1 Ω
Pp1-1 - p4-3 (RR-) Always Below 1 Ω
Pp1-5 - Pp1-8 Always 10 kΩ or higher
Pp1-5 - Pp1-4 Always 10 kΩ or higher
Pp1-5 - Pp1-1 Always 10 kΩ or higher

for LH:
Tester Connection Condition Specified Condition
Pp1-8 - p3-1 (RL+) Always Below 1 Ω
Pp1-4 - p3-3 (RL-) Always Below 1 Ω
Pp1-8 - Pp1-4 Always 10 kΩ or higher
Pp1-8 - Pp1-5 Always 10 kΩ or higher
Pp1-8 - Pp1-1 Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - REAR SPEED SENSOR)

NG

3.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - REAR SPEED SENSOR)

b.

Disconnect the A71 skid control ECU (brake actuator assembly) connector.


c.

Disconnect the p4 and p3 rear speed sensor connectors.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RH:
Tester Connection Condition Specified Condition
A71-16 (RR+) - p4-1 (RR+) Always Below 1 Ω
A71-16 (RR+) or p4-1 (RR+) - Body ground Always 10 kΩ or higher
A71-15 (RR-) - p4-3 (RR-) Always Below 1 Ω
A71-15 (RR-) or p4-3 (RR-) - Body ground Always 10 kΩ or higher

for LH:
Tester Connection Condition Specified Condition
A71-29 (RL+) - p3-1 (RL+) Always Below 1 Ω
A71-29 (RL+) or p3-1 (RL+) - Body ground Always 10 kΩ or higher
A71-28 (RL-) - p3-3 (RL-) Always Below 1 Ω
A71-28 (RL-) or p3-3 (RL-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT BRAKE ACTUATOR ASSEMBLY (SENSOR INPUT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT BRAKE ACTUATOR ASSEMBLY (SENSOR INPUT)
a.
C369076E01
1.563,0.417 1.885,0.635 0.323,0.219 1.563,0.115 1.885,0.333 0.323,0.219 2,1.208 2.688,0.74 true 0.146,0.115 0.458,0.313 0.313,0.198 10 false *a 1.646,0.135 1.958,0.333 0.313,0.198 10 false p4 1.656,0.438 1.969,0.635 0.313,0.198 10 false p3 1.979,0.135 2.292,0.333 0.313,0.198 10 false *A 1.979,0.438 2.292,0.635 0.313,0.198 10 false *B 2.75,0.625 3.281,0.833 0.531,0.208 10 false RR+ *A 2.75,0.896 3.292,1.135 0.542,0.24 10 false RL- *B

Reconnect the A71 skid control ECU (brake actuator assembly) connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for RH:
Tester Connection Condition Specified Condition
p4-1 (RR+) - Body ground Ignition switch ON 8 to 14 V

for LH:
Tester Connection Condition Specified Condition
p3-1 (RL+) - Body ground Ignition switch ON 8 to 14 V


Text in Illustration
*A for RH
*B for LH
*a Front view of wire harness connector
(to Rear Speed Sensor)


Result:
Proceed to
OK
NG



OK

NG