Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM(w/ Brake pedal Load Sensing Switch)
RM2850E _54 Brake _073264 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0356878 ANTI-LOCK BRAKE SYSTEM(w/ Brake pedal Load Sensing Switch) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM(w/ Brake pedal Load Sensing Switch)  C1427  Motor Malfunction  


DESCRIPTION

DTC No. DTC Detection Condition Trouble Area
C1427 Actuator pump motor does not operate properly.
·

Brake actuator assembly (Ground circuit)

·

Brake actuator assembly (Motor circuit)

·

Wire harness or connector



CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the skid control ECU (brake actuator assembly), perform zero point calibration and store system information (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM(w/ Brake pedal Load Sensing Switch)>CALIBRATION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (MOTOR RELAY)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Chassis / ABS/VSC/TRC / Active Test.


e.

According to the display on the GTS, perform the Active Test.

ABS/VSC/TRC
Tester Display Test Part Control Range Diagnostic Note
Motor Relay Motor relay Relay ON/OFF Operating sound of motor can be heard
Vehicle condition: Vehicle stopped


f.

Check the operating sound of the motor relay when operating it with the GTS.


Result:
Result Proceed to
The operating sound is heard A
The operating sound is not heard B



A

2.RECONFIRM DTC

B

3.CHECK HARNESS AND CONNECTOR (GND2 TERMINAL)
2.RECONFIRM DTC
HINT:

This code is detected when a problem is identified in the brake actuator assembly.

The motor relay is in the brake actuator assembly.

Therefore, motor relay unit inspection cannot be performed.

Be sure to check if the DTC is output before replacing the brake actuator assembly.


a.

Turn the ignition switch off.



c.

Turn the ignition switch off.


d.

Start the engine.


e.

Drive the vehicle at a speed of 20 km/h (12 mph) or more for 30 seconds or more.


f.

Check if the same DTC is recorded (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM(w/ Brake pedal Load Sensing Switch)>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC C1427 is not output A
DTC C1427 is output B


HINT:
·

If a speed signal of 6 km/h (4 mph) or more is input to the skid control ECU (brake actuator assembly) with the ignition switch ON and the stop light switch off, the ECU performs self-diagnosis of the motor and solenoid circuits.

·

If the normal system code is output (no trouble codes are output), slightly jiggle the connectors, wire harness, and fuses of the brake actuator assembly. Make sure that no DTCs are output.

·

If any DTCs are output while jiggling a connector or wire harness of the skid control ECU (brake actuator assembly), inspect and repair the connector or wire harness.

·

The DTCs were probably output due to a bad connection of the connector terminal.





A

B

3.CHECK HARNESS AND CONNECTOR (GND2 TERMINAL)
a.
C306843E27
1.479,0.135 1.896,0.375 0.417,0.24 0.844,1.813 0.802,0.938 true 0.146,0.083 0.458,0.281 0.313,0.198 10 false *a 1.563,0.177 1.938,0.375 0.375,0.198 10 false A71 0.698,1.833 1.292,2.031 0.594,0.198 10 false GND2

Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.


c.

Disconnect the A71 skid control ECU (brake actuator assembly) connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A71-1 (GND2) - Body ground Always Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GND2 CIRCUIT)