Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM(w/ Brake pedal Load Sensing Switch)
RM2850E _54 Brake _073264 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0356878 ANTI-LOCK BRAKE SYSTEM(w/ Brake pedal Load Sensing Switch) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM(w/ Brake pedal Load Sensing Switch)  C142B  Motor Power Supply Voltage Circuit  C146C  Open in ABS Motor Relay Circuit  C146D  Short in ABS Motor Relay Circuit  


DESCRIPTION

The motor relay and motor fail-safe relay are built into the brake actuator assembly.

During ABS or brake pressure increase function operation, the skid control ECU (brake actuator assembly) turns on the motor relay to run the pump motor in the brake actuator assembly.

When a motor system DTC is stored, the motor fail-safe relay cuts the power source supply to the motor relay for fail-safe operation.

These DTCs may be stored when the voltage to the motor relay power source (BM terminal) is lower than the DTC detection condition due to low output from the battery or alternator.

DTC No. DTC Detection Condition Trouble Area
C142B When voltage at +BS terminal is 9.5 V or higher, open in BM terminal continues for 1 second or more.
·

ABS NO. 1 fuse

·

Skid Control ECU (Brake actuator assembly)

·

Wire harness or connector


C146C When voltage at +BS terminal is 9.5 V or higher and motor relay ON while control operates, relay contact OFF condition continues for 0.12 seconds or more.
·

ABS NO. 1 fuse

·

Motor relay (Brake actuator assembly)Wire harness or connector


C146D Either of the following is detected:
1.

Overcurrent in motor relay and motor fail-safe relay continues for 0.05 seconds or more.

2.

Motor relay gate voltage malfunction continues for 0.12 seconds or more.


·

Motor relay (Brake actuator assembly)

·

Wire harness or connector



WIRING DIAGRAM

C283801E39
0.354,1.344 1.354,1.531 1,0.188 10 false from Battery 1.76,1.531 2.76,1.719 1,0.188 10 false ABS NO.1 3.375,1.24 3.646,1.427 0.271,0.188 10 false 13 3.458,2.865 3.698,3.052 0.24,0.188 10 false 1 4.719,0.74 5.979,0.938 1.26,0.198 10 false Skid Control ECU 3.677,2.865 4.177,3.042 0.5,0.177 10 false GND2 3.698,1.25 4.01,1.438 0.313,0.188 10 false BM 4.927,3.292 5.906,3.49 0.979,0.198 10 false Motor Relay 4.615,1.292 6.073,1.49 1.458,0.198 10 false Motor Fail Safe Relay 5.135,4.438 6.115,4.635 0.979,0.198 10 false Pump Motor 4.031,4.896 4.396,5.083 0.365,0.188 10 false A71 4.021,5.094 5.792,5.313 1.771,0.219 10 false Brake Actuator Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the skid control ECU (brake actuator assembly), perform calibration and store system information (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM(w/ Brake pedal Load Sensing Switch)>CALIBRATION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



HINT:

When DTC C1241 and/or C1417 is output together with DTC C142B, C146C and/or C146D, inspect and repair the trouble areas indicated by DTC C1241 and/or C1417 first (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM(w/ Brake pedal Load Sensing Switch)>C1241, or Click here Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM(w/ Brake pedal Load Sensing Switch)>C1417).


PROCEDURE

1.CHECK TERMINAL VOLTAGE (BM TERMINAL)
a.

Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.


c.
C306843E28
1.479,0.146 1.906,0.365 0.427,0.219 3.01,1.823 2.719,0.958 true 0.125,0.094 0.438,0.292 0.313,0.198 10 false *a 1.563,0.167 1.917,0.365 0.354,0.198 10 false A71 2.938,1.844 3.292,2.042 0.354,0.198 10 false BM

Disconnect the A71 skid control ECU (brake actuator assembly) connector.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A71-13 (BM) - Body ground Always 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (GND2 TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BM CIRCUIT)

2.CHECK HARNESS AND CONNECTOR (GND2 TERMINAL)
a.
C306843E27
1.479,0.135 1.896,0.375 0.417,0.24 0.844,1.813 0.802,0.938 true 0.146,0.083 0.458,0.281 0.313,0.198 10 false *a 1.563,0.177 1.938,0.375 0.375,0.198 10 false A71 0.698,1.833 1.292,2.031 0.594,0.198 10 false GND2

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A71-1 (GND2) - Body ground Always Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Result:
Proceed to
OK
NG



OK

3.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GND2 CIRCUIT)

3.RECONFIRM DTC
HINT:

These codes are stored when a problem is identified in the skid control ECU (brake actuator assembly). The motor relay is in the skid control ECU (brake actuator assembly). Therefore, motor relay inspections and motor relay unit inspections cannot be performed. Be sure to check if any DTCs are output before replacing the brake actuator assembly.


a.

Reconnect the A71 skid control ECU (brake actuator assembly) connector.



c.

Turn the ignition switch off.


d.

Start the engine.


e.

Drive the vehicle at a speed of 20 km/h (12 mph) or more for 30 seconds or more.


f.

Check if the same DTC is recorded (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM(w/ Brake pedal Load Sensing Switch)>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTCs C142B, C146C and C146D are not output A
DTCs C142B, C146C and/or C146D are output B


HINT:
·

If a speed signal of 6 km/h (4 mph) or more is input to the skid control ECU (brake actuator assembly), with the ignition switch ON and the stop light switch off, the ECU performs self-diagnosis of the motor and solenoid circuits.

·

If the normal system code is output (the trouble code is not output), slightly jiggle the connectors, wire harness, and fuses of the skid control ECU (brake actuator assembly). Make sure that no DTCs are output.

·

If any DTCs are output while jiggling a connector or wire harness from the skid control ECU (brake actuator assembly), inspect and repair the connector or wire harness.

·

The DTCs were probably output due to a bad connection of the connector terminal.





A

B