Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM(w/ Brake pedal Load Sensing Switch) › 2017.01–2019.08
RM2850E _54 Brake _073264 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0356878 ANTI-LOCK BRAKE SYSTEM(w/ Brake pedal Load Sensing Switch) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM(w/ Brake pedal Load Sensing Switch)  C1436  Yaw Rate Sensor Malfunction  


DESCRIPTION

These DTCs are stored when the skid control ECU (brake actuator assembly) receives an internal malfunction signal from the yaw rate and acceleration sensor (yaw rate sensor)*1 or yaw rate and acceleration sensor (airbag ECU assembly)*2.

These DTCs are also output when calibration has not been completed.

*1: w/o Airbag System

*2: w/ Airbag System


DTC No. DTC Detection Condition Trouble Area
C1436 Either of the following is detected:
1.

With the vehicle stationary, the yaw rate and acceleration sensor output value is not 0 deg/s.

2.

Abnormal comparison value.


·

Sensor installation

·

Yaw rate sensor*1

·

Yaw rate sensor (Airbag ECU assembly)*2



*1: w/o Airbag System

*2: w/ Airbag System


CAUTION / NOTICE / HINT

NOTICE:

When replacing the yaw rate and acceleration sensor (yaw rate sensor)*1 or yaw rate and acceleration sensor (airbag ECU assembly)*2, perform zero point calibration and store system information (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM(w/ Brake pedal Load Sensing Switch)>CALIBRATION).

*1: w/o Airbag System

*2: w/ Airbag System



HINT:

When U0124 and/or U0126 is output together with C1436, inspect and repair the trouble areas indicated by U0124 and/or U0126 first (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM(w/ Brake pedal Load Sensing Switch)>U0073).


PROCEDURE

1.READ VALUE USING USING GTS (YAW RATE SENSOR)
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.


f.

According to the display on the GTS, read the Data List.

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Yaw Rate Sensor Yaw rate sensor / Min.: -128°/s, Max.: 127°/s Vehicle stopped: 0°/s
Turning right: -128 to 0°/s
Turning left: 0 to 127°/s
-


g.

Check that the yaw rate sensor output value displayed on the GTS.

Result:
Result Proceed to
NG (The yaw rate sensor output value is 0°/s when the vehicle is stationary, but the value fluctuates when turning.) A
NG (The yaw rate sensor output value is not 0°/s when the vehicle is stationary.) (w/o Airbag System) B
NG (The yaw rate sensor output value is not 0°/s when the vehicle is stationary.) (w/ Airbag System) C
OK D


NOTICE:

Check the yaw rate sensor signal after replacement (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM(w/ Brake pedal Load Sensing Switch)>TEST MODE PROCEDURE).




A

2.CHECK YAW RATE SENSOR OR AIRBAG ECU ASSEMBLY INSTALLATION

B

C

D

2.CHECK YAW RATE SENSOR OR AIRBAG ECU ASSEMBLY INSTALLATION
a.

Turn the ignition switch off.


b.

Check that the yaw rate and acceleration sensor (yaw rate sensor)*1 or yaw rate and acceleration sensor (airbag ECU assembly)*2 has been installed properly (*1: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>YAW RATE AND ACCELERATION SENSOR (w/ Brake pedal Load Sensing Switch)>INSTALLATION, *2: Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG ECU>INSTALLATION).

*1: w/o Airbag System

*2: w/ Airbag System


OK:

The sensor should be tightened to the specified torque.

The sensor should not be installed in a tilted position.


NOTICE:

Check the yaw rate and acceleration sensor signal after replacement (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM(w/ Brake pedal Load Sensing Switch)>TEST MODE PROCEDURE).



Result:
Result Proceed to
OK (w/o Airbag System) A
OK (w/ Airbag System) B
NG (w/o Airbag System) C
NG (w/ Airbag System) D



A

B

C

D

INSTALL AIRBAG ECU ASSEMBLY CORRECTLY