Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM (w/o Brake pedal Load Sensing Switch) › 2017.01–2021.01
RM2850E _54 Brake _073264 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0356879 ANTI-LOCK BRAKE SYSTEM(w/o Brake pedal Load Sensing Switch) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM(w/o Brake pedal Load Sensing Switch)  C1251/51  Open in Pump Motor Circuit  


DESCRIPTION

DTC Code DTC Detection Condition Trouble Area
C1251/51 Actuator pump motor does not operate properly.
·

Brake actuator assembly (Ground circuit)

·

Brake actuator assembly (Motor circuit)

·

Skid control ECU



CAUTION / NOTICE / HINT

HINT:

When C0273/13 and/or C0274/14 is output together with C1251/51, inspect and repair the trouble areas indicated by C0273/13 and/or C0274/14 first (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM (w/o Brake pedal Load Sensing Switch)>C0273/13).


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (ABS MOTOR RELAY)
a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Select the Active Test mode on the GTS (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM (w/o Brake pedal Load Sensing Switch)>DATA LIST / ACTIVE TEST).

ABS / VSC / TRC:
Tester Display Test Part Control Range Diagnostic Note
ABS Motor Relay ABS motor relay Relay ON / OFF Operating sound of motor can be heard



d.

Check the operating sound of the ABS motor when operating it with the GTS.

OK:

The operating sound of the ABS motor can be heard.



Result:
Result Proceed to
The operating sound is not heard A
The operating sound is heard B



A

2.INSPECT BRAKE ACTUATOR ASSEMBLY (GND TERMINAL)

B

3.RECONFIRM DTC
2.INSPECT BRAKE ACTUATOR ASSEMBLY (GND TERMINAL)
a.

Turn the ignition switch off.


b.

Disconnect the brake actuator connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R2-1 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GND CIRCUIT)

3.RECONFIRM DTC
a.

Turn the ignition switch off.


b.

Reconnect the brake actuator connector.



d.

Start the engine.


e.

Drive the vehicle at a speed of 20 km/h (12 mph) or more for 30 seconds or more.


f.

Check if the same DTC is recorded (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM (w/o Brake pedal Load Sensing Switch)>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC (C1251/51) is not output A
DTC (C1251/51) is output B


HINT:
·

If a speed signal of 6 km/h (4 mph) or more is input to the skid control ECU, with the ignition switch ON and the stop light switch off, the ECU performs self diagnosis of the motor and solenoid circuits.

·

If the normal system code is output (the trouble code is not output), slightly jiggle the connectors, wire harness, and fuses of the skid control ECU and brake actuator assembly. Make sure that no DTCs are output.

·

If any DTCs are output while jiggling a connector or wire harness of the skid control ECU and brake actuator assembly, inspect and repair the connector or wire harness.

·

It is suspected that the DTCs were output due to a bad connection of the connector terminal.





A

B

REPLACE SKID CONTROL ECU